Articles

1. Temperature control by simulated adaptive layer times in powder bed fusion processes

   • Christoph Behrens
   • Niklas Ostermann
   • Vasily Ploshikhin

   Full Research Article Open access 25 May 2024

   

2. Novel titanium-based sulfur-containing BMG for PBF-LB/M

   • Hanna Schönrath
   • Jan Wegner
   • Stefan Kleszczynski

   Full Research Article Open access 25 May 2024

   

3. Critical review on short fiber-reinforced composite materials manufactured by material extrusion: from thermal perspective

   • Orkhan Huseynov
   • Albert E. Patterson
   • Ismail Fidan

   Review Article 25 May 2024

   

4. PBF-LB of large-area magnesium WE43 structures surface-enhanced by plasma electrolytic oxidation

   • Arvid Abel
   • Anutsek Sharma
   • Stefan Kaierle

   Full Research Article Open access 24 May 2024

   

5. β-Modification in heterogeneous polypropylene for laser-based powder bed fusion of polymers

   • Simon Cholewa
   • Thomas Forstner
   • Dietmar Drummer

   Full Research Article Open access 23 May 2024

   

6. Knowing the spectral directional emissivity of 316L and AlSi10Mg PBF-LB/M surfaces: gamechanger for quantitative in situ monitoring

   • Tina Becker
   • Thomas Stark
   • Simon J. Altenburg

   Full Research Article Open access 23 May 2024

   

7. Enhancing mechanical and morphological properties of glass fiber reinforced epoxy polymer composites through rutile nanoparticle incorporation

   • K. P. Srinivasa Perumal
   • L. Selvarajan
   • Shailesh Shriguppikar

   Full Research Article 23 May 2024

   

8. Investigation of additively manufactured lattice structures for refractive optical systems based on auxetic properties

   • Johannes Frasch
   • Henrik von Lukowicz
   • Stefan Risse

   Full Research Article Open access 21 May 2024

   

9. Fatigue behavior of 4D printed materials: a review

   • Md Jarir Hossain

   Review Article Open access 21 May 2024

   

10. Influence of wax addition on feedstock processing behavior in additive manufacturing of metals by material extrusion

    • Thomas Forstner
    • Simon Cholewa
    • Dietmar Drummer

    Full Research Article Open access 21 May 2024

    

11. Camera-based measurement and control of the contact tip to work distance in wire arc additive manufacturing

    • Moritz Baldauf
    • Philipp Lohrer
    • Johannes H. Schleifenbaum

    Full Research Article 21 May 2024

    

12. Design and implementation of a machine log for PBF-LB/M on basis of IoT communication architectures and an ETL pipeline

    • Konstantin Poka
    • Sozol Ali
    • Kai Hilgenberg

    Full Research Article Open access 21 May 2024

    

13. Zr-based bulk metallic glasses in PBF-LB/M: near-polished surface quality in the as-built state

    • Jan Wegner
    • Lars Bruckhaus
    • Stefan Kleszczynski

    Full Research Article Open access 18 May 2024

    

14. Empirical calibration method for the thermal simulation of Cu₄₇Ti₃₄Zr₁₁Ni₈ single tracks in laser powder bed fusion

    • Lars Bruckhaus
    • Jan Wegner
    • Stefan Kleszczynski

    Full Research Article Open access 18 May 2024

    

15. Cradle-to-gate life cycle assessment: a comparison of polymer and metal-based powder bed fusion for the production of a robot end-effector with internal conformal channels

    • Talha Anwar
    • A. C. Lopes
    • A. J. Pontes

    Full Research Article 18 May 2024

    

16. Efficient utilization of remelt strategy for improving relative density and surface integrity to eliminate necessity of performing post-processing of additively manufactured 316L stainless steel

    • Sajjad Rajabi
    • Alireza Khodabandeh
    • Mohammad Reza Razfar

    Full Research Article 18 May 2024

    

17. Geometry-induced process and part characteristics in support-free powder bed fusion of polypropylene at room temperature

    • Samuel Schlicht
    • Dietmar Drummer

    Full Research Article Open access 17 May 2024

    

18. Sintering of 3D-printed aluminum specimens from the slurry-based binder jetting process

    • Jan Angenoorth
    • Patricia Erhard
    • Daniel Günther

    Full Research Article Open access 17 May 2024

    

19. Exploring the environmental benefits of 3D printing technology in concrete construction; a review

    • Rania Abdelrahim Mohamed
    • Abdelaziz Farouk A. Mohamed

    Review Article 17 May 2024

    

20. Optimizing energy modeling in PBF-LB/M metal additive manufacturing: a detailed analysis of resource and energy demand based on standard tensile test specimen

    • Joachim Brinkmann
    • Jan C. Aurich
    • Henrik te Heesen

    Full Research Article Open access 16 May 2024

    

21. Degradation characteristics of 3D printed continuous fibre-reinforced PA6/chopped fibre composites in simulated saltwater

    • Pouyan Ghabezi
    • Tomas Flanagan
    • Noel M. Harrison

    Full Research Article Open access 16 May 2024

    

22. Numerical study of powder flow characteristics of coaxial nozzle direct energy deposition at different operating and design conditions

    • Yogesh Nogdhe
    • Anant Kumar Rai
    • M. Manjaiah

    Full Research Article 16 May 2024

    

23. A comparative analysis of printing parameter effects of tensile and flexural specimens produced with two different printers by the TAGUCHI method

    • Sermet Demir
    • Caner Yüksel

    Full Research Article 16 May 2024

    

24. Correction: In-process closed-loop control for stabilising the melt pool temperature in selective laser melting

    • Volker Renken
    • Axel von Freyberg
    • Andreas Fischer

    Correction Open access 15 May 2024

25. 3D concrete printing success: an exhaustive diagnosis and failure modes analysis

    • Fatima Zahra Oulkhir
    • Iatimad Akhrif
    • Mostapha El Jai

    Review Article 15 May 2024

    

26. Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering

    • A. Röttger
    • L. Wieczorek
    • M. Löwer

    Full Research Article Open access 14 May 2024

    

27. Experimental study on the effect of filament-extrusion rate on the structural, mechanical and thermal properties of material extrusion 3D-printed polylactic acid (PLA) products

    • László Lendvai
    • Imre Fekete
    • Alessandro Pegoretti

    Full Research Article Open access 12 May 2024

    

28. Surface finish enhancement in fused deposition modeling of PLA using chloroform: a comprehensive characterization study

    • Ali Akhavan Farid
    • Tshai Kim Yeow
    • Kamesh Krishnamurariu

    Full Research Article 12 May 2024

    

29. Analysis of phase, microstructure, and mechanical characteristics of selective laser melted AlSi10Mg alloy after post-heat treatment

    • B. Sai Charan
    • M. Srikanth
    • Deepak K. Pattanayak

    Full Research Article 10 May 2024

    

30. Numerical simulation and experimental investigation of temperature distribution during the wire arc additive manufacturing (WAAM) process

    • Deepak Kumar Gupta
    • Rahul S. Mulik

    Full Research Article 09 May 2024

    

31. Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing

    • Björn Ringel
    • David Schwarz
    • Matthias Oechsner

    Correction Open access 08 May 2024

32. The effect of hot isostatic pressing pressure level and solution annealing cooling rate on CM247 LC nickel-based superalloy processed by laser-based powder bed fusion

    • P. A. Martelli
    • E. Bassini
    • D. Ugues

    Full Research Article Open access 08 May 2024

    

33. The effect of interface enhancement on the mechanical properties of fibre-reinforced PA6 matrix composites in material extrusion-based additive manufacturing

    • Alperen Doğru
    • Mehmet Özgür Seydibeyoğlu
    • Cagri Ayranci

    Full Research Article 07 May 2024

    

34. In situ build surface topography determination in electron beam powder bed fusion

    • Jakob Renner
    • Matthias Markl
    • Carolin Körner

    Full Research Article Open access 07 May 2024

    

35. Improving a tool-path optimisation method in material extrusion additive manufacturing by data clustering and collapsing

    • N. Volpato
    • T. R. Weller
    • F. C. Becheli

    Full Research Article 06 May 2024

    

36. Effect of a process interruption on the mechanical properties of AlSi10Mg components produced by laser powder bed fusion (PBF-LB/M)

    • M. Moser
    • S. Brenner
    • V. Nedeljkovic-Groha

    Full Research Article Open access 06 May 2024

    

37. Prediction of the penetration depth of particle-loaded inks in binder jetting

    • Maja Lehmann
    • Cara G. Kolb
    • Michael F. Zaeh

    Full Research Article Open access 06 May 2024

    

38. Investigating the reversible performance of shape memory composites in 4D printing using magnetic field stimulation: case study of polylactic acid/SrFe₁₂O₁₉ composite filament

    • Seyed Mohammad Reza Sotoudeh
    • Milad Sadegh Yazdi
    • Mohammad Hassanpour

    Full Research Article 05 May 2024

    

39. Influence of process parameters on the occurrence of defects and dimensional properties of green part produced by material extrusion of highly filled polymer

    • Raphaël Côté
    • Dorian Delbergue
    • Jérémie Soulestin

    Full Research Article 03 May 2024

    

40. Energy absorption of multi-scale hierarchically graded auxetic structures: experimental and simulation methods

    • A. R. Mortezapour
    • A. Hosseini Monazzah
    • M. Sameezadeh

    Full Research Article 02 May 2024

    

41. Laser powder bed fusion processing of UNS C63020 nickel aluminum bronze powder

    • A. J. Rayner
    • J. Hierlihy
    • D. P. Bishop

    Full Research Article 02 May 2024

    

42. Fused granulate fabrication of injection molding inserts from high-performance ULTEM 9085™ thermoplastic for cosmetic packaging industry

    • Albert Curmi
    • Arif Rochman

    Full Research Article Open access 01 May 2024

    

43. Strain sensing characteristics of 3D-printed carbon nanotubes/polypyrrole/UV-curable composites: experimental validation and machine learning predictions

    • Nutthapong Poompiew
    • Wiwittawin Sukmas
    • Pranut Potiyaraj

    Full Research Article 01 May 2024

    

44. Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing

    • Björn Ringel
    • David Schwarz
    • Matthias Oechsner

    Correction Open access 29 April 2024

45. Investigation of the effects of volume fraction, aspect ratio and type of fibres on the mechanical properties of short fibre reinforced 3D printed composite materials

    • Hassan Gonabadi
    • Yao Chen
    • Steve Bull

    Full Research Article Open access 29 April 2024

    

46. Benchmark study of melt pool and keyhole dynamics, laser absorptance, and porosity in additive manufacturing of Ti-6Al-4V

    • Arash Samaei
    • Joseph P. Leonor
    • Gregory J. Wagner

    Full Research Article 29 April 2024

    

47. Strength evaluation of polymer ceramic composites: a comparative study between injection molding and fused filament fabrication techniques

    • Lovin K. John
    • M. Ramu
    • Nandhu Binudas

    Full Research Article 27 April 2024

    

48. Integrating resistance-based sensing into fused filament fabricated mechanical metamaterial structure

    • Imran Khan
    • Muhammad Yaseen
    • Fatima Hira

    Full Research Article 26 April 2024

    

49. Process parameter optimization of pulsed laser deposition of hydroxyapatite coated polymer implant for better surface roughness and cell viability

    • K. Hariharan
    • N. Sathishkumar
    • G. Arumaikkannu

    Full Research Article 26 April 2024

    

50. Microstructure and tribological properties of solid lubricant-doped CMT-WAAMed Stellite deposits

    • Jari Tuominen
    • Ali Sabr
    • Pasi Peura

    Full Research Article Open access 22 April 2024