1. Foreword “Best of Gears 2022”

   • Karsten Stahl

   Mitteilung der Herausgeber/Editorial Open access 10 August 2022 Pages: 249 - 249

2. Gear root bending strength: statistical treatment of Single Tooth Bending Fatigue tests results

   • Luca Bonaiti
   • Francesco Rosa
   • Carlo Gorla

   Originalarbeiten/Originals 15 November 2021 Pages: 251 - 258

   

3. A comparison of gear tooth bending fatigue lives from single tooth bending and rotating gear tests

   • Isaac Hong
   • Zach Teaford
   • Ahmet Kahraman

   Originalarbeiten/Originals 13 September 2021 Pages: 259 - 271

   

4. Innovative tooth contact analysis with non-uniform rational b-spline surfaces

   • Felix Müller
   • Stefan Schumann
   • Berthold Schlecht

   Originalarbeiten/Originals Open access 13 September 2021 Pages: 273 - 281

   

5. Dynamic load distribution of planetary gear sets subject to both internal and external excitations

   • Lokaditya Ryali
   • David Talbot

   Originalarbeiten/Originals 08 July 2021 Pages: 283 - 294

   

6. Experimental investigation of the dynamic load sharing of planetary gearboxes

   • J. Götz
   • F. Siglmüller
   • K. Stahl

   Originalarbeiten/Originals Open access 08 July 2021 Pages: 295 - 302

   

7. Influences on the excitation behavior of lightweight planetary gearboxes

   • Julian Theling
   • Jens Brimmers
   • Christian Brecher

   Originalarbeiten/Originals Open access 13 September 2021 Pages: 303 - 313

   

8. Influence of thin–rimmed/-webbed gears on transmission dynamic behaviour—Approximate dynamic factor formula

   • B. Guilbert
   • P. Velex

   Originalarbeiten/Originals 06 October 2021 Pages: 315 - 320

   

9. Minimum friction losses in wind turbine gearboxes

   • José I. Pedrero
   • Débora Martínez-López
   • Alfredo Fernández-Sisón

   Originalarbeiten/Originals Open access 15 September 2021 Pages: 321 - 330

   

10. Gear mesh excitation and non-uniform Rational B-Splines

    • A. Beinstingel
    • M. Heider
    • S. Marburg

    Originalarbeiten/Originals 15 September 2021 Pages: 331 - 336

    

11. Contact characteristics of cycloid planetary gear drives considering backlashes and clearances

    • Ling-Chiao Chang
    • Shyi-Jeng Tsai
    • Ching-Hao Huang

    Originalarbeiten/Originals 13 September 2021 Pages: 337 - 356

    

12. Analyse der Wirkmechanismen im fluidfreien Wälzkontakt mit beschichteten Oberflächen

    • Sebastian Sklenak
    • Jens Brimmers
    • Christian Brecher

    Originalarbeiten/Originals Open access 13 September 2021 Pages: 357 - 366

    

13. Wear simulation of worm gears based on an energetic approach

    • K. Daubach
    • M. Oehler
    • B. Sauer

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 367 - 377

    

14. Prediction of churning losses in an industrial gear box with spiral bevel gears using the smoothed particle hydrodynamic method

    • B. Legrady
    • M. Taesch
    • C. F. Mieth

    Originalarbeiten/Originals 13 September 2021 Pages: 379 - 388

    

15. On windage power loss reduction achieved by flanges

    • Y. Marchesse
    • M. Ruzek
    • P. Velex

    Originalarbeiten/Originals 01 December 2021 Pages: 389 - 394

    

16. CFD analysis on the oil flow of a gear stage with guide plate

    • Lucas Hildebrand
    • Florian Dangl
    • Karsten Stahl

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 395 - 408

    

17. Automation of gearbox design

    • Marius Fürst
    • Joshua Götz
    • Karsten Stahl

    Originalarbeiten/Originals Open access 13 September 2021 Pages: 409 - 420

    

18. Sensor-integrating gears: wear detection by in-situ MEMS acceleration sensors

    • Julian Peters
    • Lorenz Ott
    • Sven Matthiesen

    Originalarbeiten/Originals Open access 23 December 2021 Pages: 421 - 432

    

19. Application of genetic algorithms for parameters identification in a developing smart gear system

    • T. T. Mac
    • D. Iba
    • I. Moriwaki

    Übersichtsarbeiten/Review articles 15 January 2022 Pages: 433 - 450

    

20. Feasibility study of measuring instantaneous angular speed of helical gears with magnetoresistive sensors

    • Yanik Koch
    • G. Martin
    • R. Slatter

    Originalarbeiten/Originals Open access 12 July 2022 Pages: 451 - 459

    

21. Enhanced loaded tooth contact analysis of hypoid gears within a multi-body-system simulation

    • Wolf Wagner
    • Stefan Schumann
    • Berthold Schlecht

    Originalarbeiten/Originals Open access 31 January 2022 Pages: 461 - 470

    

22. Suitability of the test results of micropitting tests acc. to FVA 54/7 for modern practical gear applications

    • Nadine Sagraloff
    • Thomas Tobie
    • Karsten Stahl

    Übersichtsarbeiten/Review articles Open access 09 July 2021 Pages: 471 - 481

    

23. Mode III threshold under Rolling Contact Fatigue and development of a test gearbox for planet gears

    • Prasad Mahendra Rao
    • Stefano Foletti
    • Stefano Beretta

    Originalarbeiten/Originals 14 January 2022 Pages: 483 - 490

    

24. Stress calculation on bevel gears with FEM influence vectors

    • Frederik Mieth
    • Carsten Ulrich
    • Berthold Schlecht

    Originalarbeiten/Originals Open access 21 October 2021 Pages: 491 - 501

    

25. Scuffing load capacity calculation of worm gears

    • Philipp Roth
    • Michael Hein
    • Karsten Stahl

    Originalarbeiten/Originals Open access 06 July 2021 Pages: 503 - 511

    

26. Scuffing of cylindrical gears with pitch line velocities up to 100 m/s

    • J. Vorgerd
    • P. Tenberge
    • M. Joop

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 513 - 520

    

27. Calculating component temperatures in gearboxes for transient operation conditions

    • Constantin Paschold
    • Martin Sedlmair
    • Karsten Stahl

    Originalarbeiten/Originals Open access 13 September 2021 Pages: 521 - 534

    

28. Load-Capacity Evaluation of Polyacetal (POM) internal gears according to JIS B 1759:2016 (Effect of number of teeth of pinion)

    • I. Moriwaki
    • K. Tatsuoka
    • A. Ueda

    Originalarbeiten/Originals 03 January 2022 Pages: 535 - 544

    

29. In situ investigation of the influence of varying load conditions on tooth deformation and wear of polymer gears

    • Christoph Herzog
    • Michael Wolf
    • Dietmar Drummer

    Originalarbeiten/Originals Open access 19 July 2022 Pages: 545 - 555

    

30. Operating behavior and performance of oil-lubricated plastic gears

    • C. M. Illenberger
    • T. Tobie
    • K. Stahl

    Originalarbeiten/Originals Open access 13 September 2021 Pages: 557 - 565

    

31. Erratum to: Operating behavior and performance of oil-lubricated plastic gears

    • C. M. Illenberger
    • T. Tobie
    • K. Stahl

    Erratum 13 October 2021 Pages: 567 - 567

32. Plastic gear remaining useful life prediction using artificial neural network

    • B. H. Kien
    • D. Iba
    • I. Moriwaki

    Originalarbeiten/Originals 21 October 2021 Pages: 569 - 585

    

33. Tool wear development in gear skiving process of quenched and tempered internal gears

    • Tassilo Arndt
    • Jan Klose
    • Volker Schulze

    Originalarbeiten/Originals Open access 21 October 2021 Pages: 587 - 594

    

34. Increasing the safety against scuffing of additive manufactured gear wheels by internal cooling channels

    • Hans-Jörg Dennig
    • Livia Zumofen
    • Simon Winterberg

    Originalarbeiten/Originals Open access 13 September 2021 Pages: 595 - 604

    

35. Quality improvement of an aluminum gearbox housing by implementing additive manufacturing

    • P. Barreiro
    • G. Armutcu
    • J. Hermes

    Originalarbeiten/Originals 21 October 2021 Pages: 605 - 616

    

36. Direct flank geometry calculation for face gears

    • Jonas-Frederick Hochrein
    • Maximilian Trübswetter
    • Karsten Stahl

    Originalarbeiten/Originals 07 July 2021 Pages: 617 - 625

    

37. Approach for multiscale modeling the thermomechanical tool load in gear hobbing

    • Nico Troß
    • Jens Brimmers
    • Thomas Bergs

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 627 - 638

    

38. Consideration of micro-interaction in the modeling of generating gear grinding processes

    • Patricia de Oliveira Teixeira
    • J. Brimmers
    • T. Bergs

    Originalarbeiten/Originals 13 September 2021 Pages: 639 - 647

    

39. Deep nitriding—contact and bending strength of gears with increased nitriding hardening depth

    • André Sitzmann
    • Stefanie Hoja
    • Karsten Stahl

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 649 - 659

    

40. Influence of grinding zones on the tooth root bending strength of case carburized gears

    • Karl Jakob Winkler
    • Thomas Tobie
    • Karsten Stahl

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 661 - 671

    

41. Modelling and prevention of meshing interference in gear skiving of internal gears

    • Andreas Hilligardt
    • Jan Klose
    • Volker Schulze

    Originalarbeiten/Originals Open access 15 September 2021 Pages: 673 - 681