1. Introduction

   • Mathias Göken
   • Gunther Eggeler
   • Lei Lu

   Mechanical Properties and Microstructure of Advanced Metallic Alloys in Honor of Prof. Haël Mughrabi — Part B — High Temperature and Nanomaterials 28 December 2017 Pages: 4463 - 4465

   

2. Creep behavior of a γ′-strengthened Co-base alloy with zero γ/γ′-lattice misfit at 800 °C, 196 MPa

   • Jan Midtlyng
   • Alexander I. Epishin
   • Walter Reimers

   Article 09 November 2017 Pages: 4466 - 4474

   

3. High temperature properties and fatigue strength of novel wrought γ/γ′ Co-base superalloys

   • Lisa Patricia Freund
   • Sven Giese
   • Mathias Göken

   Article 22 August 2017 Pages: 4475 - 4482

   

4. Equal channel angular pressing with rotating shear plane to produce hybrid materials with helical architecture of constituents

   • Rimma Lapovok
   • Andrey Molotnikov
   • Yuri Estrin

   Article 11 September 2017 Pages: 4483 - 4490

   

5. Transmission electron microscopy study of the microstructural evolution during high-temperature and low-stress (011) \(\left[{01\bar 1} \right]\) shear creep deformation of the superalloy single crystal LEK 94

   • Leonardo Agudo Jácome
   • Gülcan Göbenli
   • Gunther Eggeler

   Article 15 September 2017 Pages: 4491 - 4502

   

6. Static recrystallization and grain growth of accumulative roll bonded aluminum laminates

   • Laura Lienshöft
   • Paul Chekhonin
   • Werner Skrotzki

   Article 12 October 2017 Pages: 4503 - 4513

   

7. In situ study of thermally activated flow and dynamic restoration of ultrafine-grained pure Cu at 373 K

   • Wolfgang Blum
   • Petr Král
   • Vaclav Sklenička

   Article 18 September 2017 Pages: 4514 - 4521

   

8. Microstructure evolution in L1₂ hardened Co-base superalloys during creep

   • Yuzhi Li
   • Florian Pyczak
   • Zekun Yao

   Article 18 September 2017 Pages: 4522 - 4530

   

9. Microstructures and hardness properties of laser clad Ni base two-phase intermetallic alloy coating

   • Takeshi Okuno
   • Yasuyuki Kaneno
   • Takayuki Takasugi

   Article 05 September 2017 Pages: 4531 - 4540

   

10. An examination of the superplastic characteristics of Al–Mg–Sc alloys after processing

    • Pedro H. R. Pereira
    • Yi Huang
    • Terence G. Langdon

    Review 25 July 2017 Pages: 4541 - 4553

    

11. Thickness effect on fracture behavior of columnar-grained Cu with preferentially oriented nanoscale twins

    • Shusen Luo
    • Zesheng You
    • Lei Lu

    Article 22 August 2017 Pages: 4554 - 4562

    

12. Tensile creep of miniaturized specimens

    • LiKang Luan
    • Heinz Riesch-Oppermann
    • Martin Heilmaier

    Article 24 October 2017 Pages: 4563 - 4572

    

13. Crack propagation and mechanical properties of electrodeposited nickel with bimodal microstructures in the nanocrystalline and ultrafine grained regime

    • Dominic Rathmann
    • Michael Marx
    • Christian Motz

    Article 26 September 2017 Pages: 4573 - 4582

    

14. Influence of solid solution strengthening on the local mechanical properties of single crystal and ultrafine-grained binary Cu–Al X solid solutions

    • Verena Maier-Kiener
    • Xianghai An
    • Karsten Durst

    Article 22 August 2017 Pages: 4583 - 4591

    

15. Hydrogen embrittlement behaviors of ultrafine-grained 22Mn–0.6C austenitic twinning induced plasticity steel

    • Yu Bai
    • Yanzhong Tian
    • Nobuhiro Tsuji

    Article 20 September 2017 Pages: 4592 - 4604

    

16. Phase field modeling of solidification in multi-component alloys with a case study on the Inconel 718 alloy

    • Michael Fleck
    • Frank Querfurth
    • Uwe Glatzel

    Article 26 October 2017 Pages: 4605 - 4615

    

17. Deformation mechanisms in submicron Be wires

    • Frédéric Mompiou
    • Marc Legros
    • Sylvie Lartigue-Korinek

    Article 21 August 2017 Pages: 4616 - 4625