Articles

1. Geometry-induced process and part characteristics in support-free powder bed fusion of polypropylene at room temperature

   • Samuel Schlicht
   • Dietmar Drummer

   Full Research Article Open access 17 May 2024

   

2. Sintering of 3D-printed aluminum specimens from the slurry-based binder jetting process

   • Jan Angenoorth
   • Patricia Erhard
   • Daniel Günther

   Full Research Article Open access 17 May 2024

   

3. Optimizing energy modeling in PBF-LB/M metal additive manufacturing: a detailed analysis of resource and energy demand based on standard tensile test specimen

   • Joachim Brinkmann
   • Jan C. Aurich
   • Henrik te Heesen

   Full Research Article Open access 16 May 2024

   

4. Degradation characteristics of 3D printed continuous fibre-reinforced PA6/chopped fibre composites in simulated saltwater

   • Pouyan Ghabezi
   • Tomas Flanagan
   • Noel M. Harrison

   Full Research Article Open access 16 May 2024

   

5. Numerical study of powder flow characteristics of coaxial nozzle direct energy deposition at different operating and design conditions

   • Yogesh Nogdhe
   • Anant Kumar Rai
   • M. Manjaiah

   Full Research Article 16 May 2024

   

6. A comparative analysis of printing parameter effects of tensile and flexural specimens produced with two different printers by the TAGUCHI method

   • Sermet Demir
   • Caner Yüksel

   Full Research Article 16 May 2024

   

7. Correction: In-process closed-loop control for stabilising the melt pool temperature in selective laser melting

   • Volker Renken
   • Axel von Freyberg
   • Andreas Fischer

   Correction Open access 15 May 2024

8. 3D concrete printing success: an exhaustive diagnosis and failure modes analysis

   • Fatima Zahra Oulkhir
   • Iatimad Akhrif
   • Mostapha El Jai

   Review Article 15 May 2024

   

9. Additive manufacturing of carbon-martensitic hardening ledeburitic cold work tool steels using Fused Filament Fabrication and subsequent Supersolidus Liquid-Phase Sintering

   • A. Röttger
   • L. Wieczorek
   • M. Löwer

   Full Research Article Open access 14 May 2024

   

10. Experimental study on the effect of filament-extrusion rate on the structural, mechanical and thermal properties of material extrusion 3D-printed polylactic acid (PLA) products

    • László Lendvai
    • Imre Fekete
    • Alessandro Pegoretti

    Full Research Article Open access 12 May 2024

    

11. Surface finish enhancement in fused deposition modeling of PLA using chloroform: a comprehensive characterization study

    • Ali Akhavan Farid
    • Tshai Kim Yeow
    • Kamesh Krishnamurariu

    Full Research Article 12 May 2024

    

12. Analysis of phase, microstructure, and mechanical characteristics of selective laser melted AlSi10Mg alloy after post-heat treatment

    • B. Sai Charan
    • M. Srikanth
    • Deepak K. Pattanayak

    Full Research Article 10 May 2024

    

13. Numerical simulation and experimental investigation of temperature distribution during the wire arc additive manufacturing (WAAM) process

    • Deepak Kumar Gupta
    • Rahul S. Mulik

    Full Research Article 09 May 2024

    

14. Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing

    • Björn Ringel
    • David Schwarz
    • Matthias Oechsner

    Correction Open access 08 May 2024

15. The effect of hot isostatic pressing pressure level and solution annealing cooling rate on CM247 LC nickel-based superalloy processed by laser-based powder bed fusion

    • P. A. Martelli
    • E. Bassini
    • D. Ugues

    Full Research Article Open access 08 May 2024

    

16. The effect of interface enhancement on the mechanical properties of fibre-reinforced PA6 matrix composites in material extrusion-based additive manufacturing

    • Alperen Doğru
    • Mehmet Özgür Seydibeyoğlu
    • Cagri Ayranci

    Full Research Article 07 May 2024

    

17. In situ build surface topography determination in electron beam powder bed fusion

    • Jakob Renner
    • Matthias Markl
    • Carolin Körner

    Full Research Article Open access 07 May 2024

    

18. Improving a tool-path optimisation method in material extrusion additive manufacturing by data clustering and collapsing

    • N. Volpato
    • T. R. Weller
    • F. C. Becheli

    Full Research Article 06 May 2024

    

19. Effect of a process interruption on the mechanical properties of AlSi10Mg components produced by laser powder bed fusion (PBF-LB/M)

    • M. Moser
    • S. Brenner
    • V. Nedeljkovic-Groha

    Full Research Article Open access 06 May 2024

    

20. Prediction of the penetration depth of particle-loaded inks in binder jetting

    • Maja Lehmann
    • Cara G. Kolb
    • Michael F. Zaeh

    Full Research Article Open access 06 May 2024

    

21. Investigating the reversible performance of shape memory composites in 4D printing using magnetic field stimulation: case study of polylactic acid/SrFe₁₂O₁₉ composite filament

    • Seyed Mohammad Reza Sotoudeh
    • Milad Sadegh Yazdi
    • Mohammad Hassanpour

    Full Research Article 05 May 2024

    

22. Influence of process parameters on the occurrence of defects and dimensional properties of green part produced by material extrusion of highly filled polymer

    • Raphaël Côté
    • Dorian Delbergue
    • Jérémie Soulestin

    Full Research Article 03 May 2024

    

23. Energy absorption of multi-scale hierarchically graded auxetic structures: experimental and simulation methods

    • A. R. Mortezapour
    • A. Hosseini Monazzah
    • M. Sameezadeh

    Full Research Article 02 May 2024

    

24. Laser powder bed fusion processing of UNS C63020 nickel aluminum bronze powder

    • A. J. Rayner
    • J. Hierlihy
    • D. P. Bishop

    Full Research Article 02 May 2024

    

25. Fused granulate fabrication of injection molding inserts from high-performance ULTEM 9085™ thermoplastic for cosmetic packaging industry

    • Albert Curmi
    • Arif Rochman

    Full Research Article Open access 01 May 2024

    

26. Strain sensing characteristics of 3D-printed carbon nanotubes/polypyrrole/UV-curable composites: experimental validation and machine learning predictions

    • Nutthapong Poompiew
    • Wiwittawin Sukmas
    • Pranut Potiyaraj

    Full Research Article 01 May 2024

    

27. Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing

    • Björn Ringel
    • David Schwarz
    • Matthias Oechsner

    Correction Open access 29 April 2024

28. Investigation of the effects of volume fraction, aspect ratio and type of fibres on the mechanical properties of short fibre reinforced 3D printed composite materials

    • Hassan Gonabadi
    • Yao Chen
    • Steve Bull

    Full Research Article Open access 29 April 2024

    

29. Benchmark study of melt pool and keyhole dynamics, laser absorptance, and porosity in additive manufacturing of Ti-6Al-4V

    • Arash Samaei
    • Joseph P. Leonor
    • Gregory J. Wagner

    Full Research Article 29 April 2024

    

30. Strength evaluation of polymer ceramic composites: a comparative study between injection molding and fused filament fabrication techniques

    • Lovin K. John
    • M. Ramu
    • Nandhu Binudas

    Full Research Article 27 April 2024

    

31. Integrating resistance-based sensing into fused filament fabricated mechanical metamaterial structure

    • Imran Khan
    • Muhammad Yaseen
    • Fatima Hira

    Full Research Article 26 April 2024

    

32. Process parameter optimization of pulsed laser deposition of hydroxyapatite coated polymer implant for better surface roughness and cell viability

    • K. Hariharan
    • N. Sathishkumar
    • G. Arumaikkannu

    Full Research Article 26 April 2024

    

33. Microstructure and tribological properties of solid lubricant-doped CMT-WAAMed Stellite deposits

    • Jari Tuominen
    • Ali Sabr
    • Pasi Peura

    Full Research Article Open access 22 April 2024

    

34. Definitive screening design for mechanical properties enhancement in extrusion-based additive manufacturing of carbon fiber-reinforced PLA composite

    • Muhammad Abas
    • Tufail Habib
    • Sahar Noor

    Full Research Article 21 April 2024

    

35. Additive manufacturing for producing microchannel heat sinks

    • A. N. Kivanani
    • S. Khalilpourazary
    • F. Mobadersani

    Review Article 21 April 2024

    

36. Exosome loaded 3D printed magnetic PLA constructs: a candidate for bone tissue engineering

    • Rihab Ksouri
    • Sedat Odabas
    • Atiye Seda Yar Sağlam

    Full Research Article 21 April 2024

    

37. Factors affecting interface bonding in multi-material additive manufacturing

    • Sarah Delia
    • Arif Rochman
    • Albert Curmi

    Full Research Article Open access 19 April 2024

    

38. Clad-geometric characteristics and melt-pool behavior on microstructure evolution of laser clad Stellite-6 on R260 grade rail steel

    • Kirati Waree
    • Paiboon Wattanapornphan
    • Ussadawut Patakham

    Full Research Article 19 April 2024

    

39. High-performance thermoplastics obtained by fused filament fabrication: effects of harsh environmental conditions of power transformers

    • Catarina Costa
    • Pedro Lopes
    • Thiago Assis Dutra

    Full Research Article Open access 17 April 2024

    

40. Towards sustainable injection moulding using 3D printed conformal cooling channels: a comparative simulation study

    • Rebecca Clark
    • Arif Rochman
    • Pierre Vella

    Full Research Article Open access 16 April 2024

    

41. Investigations on mass flow rate of rotary vane feeder for direct metal laser deposition

    • S. Pratheesh Kumar
    • J. R. Ramakrishna
    • S. Karthikeyan

    Full Research Article 16 April 2024

    

42. Innovative continuous polypropylene fiber composite filament for material extrusion

    • Yongzhe Yan
    • Selvum Pillay
    • Haibin Ning

    Full Research Article 16 April 2024

    

43. Deep learning-based melt pool and porosity detection in components fabricated by laser powder bed fusion

    • Zhaochen Gu
    • K. V. Mani Krishna
    • Narendra B. Dahotre

    Full Research Article 15 April 2024

    

44. Advanced medical monitoring: 3D printed prosthetics with integrated strain sensor

    • Tomás Resendes
    • Patrícia Freitas Rodrigues
    • Maria Teresa Vieira

    Review Article 15 April 2024

    

45. Physics-Informed Machine Learning for metal additive manufacturing

    • Abdelrahman Farrag
    • Yuxin Yang
    • Yu Jin

    Review Article 15 April 2024

    

46. Functional graded NiTi manufactured with powder bed fusion

    • Rico Weber
    • Enrico Tosoratti
    • Konrad Wegener

    Full Research Article Open access 15 April 2024

    

47. Simulation-based process parameter optimization for wire arc additive manufacturing

    • Jendrik-Alexander Tröger
    • Stefan Hartmann
    • Volker Wesling

    Full Research Article Open access 12 April 2024

    

48. A response surface methodology study on 4D printing for layered PLA/TPU structures

    • Abbas Zolfaghari
    • Mohammad Reza Purrouhani
    • Ali Zolfagharian

    Full Research Article 11 April 2024

    

49. Influence of 3D-printing deposition parameters on crystallinity and morphing properties of PLA-based materials

    • Mylene S. Cadete
    • Tiago E. P. Gomes
    • Victor Neto

    Full Research Article Open access 11 April 2024

    

50. Mechanical properties of lightweight 3D-printed structures made with carbon-filled nylon

    • Roberto Spina
    • Luigi Morfini
    • Luigi M. Galantucci

    Full Research Article Open access 11 April 2024