Additively manufactured heat exchangers: a review on opportunities and challenges Seyed A. NiknamMehdi MortazaviDongsheng Li Critical Review 22 November 2020 Pages: 601 - 618
A review on magnetic abrasive finishing Cheng QianZenghua FanJinhui Wang Critical Review 25 November 2020 Pages: 619 - 634
3D printed composite materials for craniofacial implants: current concepts, challenges and future directions Swati JindalFaisal ManzoorElena Mancuso Critical Review Open access 03 December 2020 Pages: 635 - 653
A review on micro-milling: recent advances and future trends Barnabás Zoltán BalázsNorbert GeierJ. Paulo Davim Critical Review Open access 28 December 2020 Pages: 655 - 684
Success factors for introducing industrial human-robot interaction in practice: an empirically driven framework Tobias KoppMarco BaumgartnerSteffen Kinkel Survey Paper Open access 09 December 2020 Pages: 685 - 704
Morphology and properties of diamond-copper/steel matrix abrasive composites prepared by roll-bonding technique Wei-dong ChenYan-guo LiMing-zhi Wang ORIGINAL ARTICLE 27 August 2020 Pages: 705 - 717
Optimization of wire electrical discharge turning process: trade-off between production rate and fatigue life Pouyan TalebizadehsardariArameh EyvazianTamer A. Sebaey ORIGINAL ARTICLE 18 November 2020 Pages: 719 - 730
Holistic sustainability assessment of hybrid Al–GnP-enriched nanofluids and textured tool in machining of Ti–6Al–4V alloy Aqib Mashood KhanGhulam HussainNing He ORIGINAL ARTICLE 23 November 2020 Pages: 731 - 743
Correction to: Holistic sustainability assessment of hybrid Al-GnP enriched nanofluids and textured-tool in machining of Ti-6Al-4V alloy Aqib Mashood KhanGhulam HussainNing He Correction 04 December 2020 Pages: 745 - 745
Many-objective optimization of build part orientation in additive manufacturing Marina A. MatosAna Maria A. C. RochaLino A. Costa ORIGINAL ARTICLE 23 November 2020 Pages: 747 - 762
Electrically assisted deep drawing on high-strength steel sheet Z. LvY. ZhouS. Qin ORIGINAL ARTICLE 23 November 2020 Pages: 763 - 773
Machining characteristics of Ti6Al4V alloy in laser-assisted machining under minimum quantity lubricant Xiaosheng LuanJianbing MengLinghui Qu ORIGINAL ARTICLE 23 November 2020 Pages: 775 - 785
Environmental impacts of conventional and additive manufacturing for the production of Ti-6Al-4V knee implant: a life cycle approach Ronan LyonsAnthony NewellNikolaos Papakostas ORIGINAL ARTICLE 24 November 2020 Pages: 787 - 801
Design and optimization of rolling mills pass based on parameterization and orthogonal test Quan WangPan HuangYehong Yin ORIGINAL ARTICLE 24 November 2020 Pages: 803 - 818
Rolling bearing fault diagnosis based on feature fusion with parallel convolutional neural network Mingxuan LiangPei CaoJ. Tang ORIGINAL ARTICLE 24 November 2020 Pages: 819 - 831
Modeling and fitting of an ultrasonic straight-blade cutting system Ke MaJianfu ZhangZhijun Wu ORIGINAL ARTICLE 24 November 2020 Pages: 833 - 843
Exploring cutting front profile in abrasive water jet machining of aluminum alloys Shu WangDong HuPeng Lin ORIGINAL ARTICLE 25 November 2020 Pages: 845 - 851
Predicting the evolution of sheet metal surface scratching by the technique of artificial intelligence Wei LiLiangchi ZhangChao Niu ORIGINAL ARTICLE 25 November 2020 Pages: 853 - 865
The effect of laser welding modes on mechanical properties and microstructure of 304L stainless steel parts fabricated by laser-foil-printing additive manufacturing Chia-Hung HungWei-Ting ChenMing C. Leu ORIGINAL ARTICLE 25 November 2020 Pages: 867 - 877
Numerical investigation of thermal behavior and melt pool morphology in multi-track multi-layer selective laser melting of the 316L steel Saad WaqarQidong SunJie Sun ORIGINAL ARTICLE 25 November 2020 Pages: 879 - 895
Effect of multi-point roller dies on the forming accuracy of profile in flexible 3D stretch bending technology Yi LiXiao HanCe Liang ORIGINAL ARTICLE 25 November 2020 Pages: 897 - 905
Nonlinear control of the HAGC by backstepping with integral action based on a circle-criterion observer Abdelmajid AkilNabila Rabbah ORIGINAL ARTICLE 25 November 2020 Pages: 907 - 924
UV laser cutting of beech plywood Kam Chuen YungHang Shan ChoyZhixiang Cai ORIGINAL ARTICLE 26 November 2020 Pages: 925 - 947
An approach to model manufacturing of an enhanced swing differential Colpitts oscillator based on heterostructures to increase density of their elements with account mismatch-induced stress: on optimization of annealing E. L. Pankratov ORIGINAL ARTICLE 26 November 2020 Pages: 949 - 967
A novel and effective method for cryogenic milling of polytetrafluoroethylene Yongquan GanYongqing WangHaibo Liu ORIGINAL ARTICLE 27 November 2020 Pages: 969 - 976
An investigation into cutting fluid additives performance during machining processing of Ti-6Al-4V Junhui MaJavad MohammadiReza A. Riahi ORIGINAL ARTICLE 27 November 2020 Pages: 977 - 987
Analysis of the machinability when milling AlSi10Mg additively manufactured via laser-based powder bed fusion Marco ZimmermannDaniel MüllerJan C. Aurich ORIGINAL ARTICLE Open access 27 November 2020 Pages: 989 - 1005
Parametric modeling method for integrated design and manufacturing of radial compressor impeller Yu ZhouYue SongShuiting Ding ORIGINAL ARTICLE 27 November 2020 Pages: 1007 - 1021
An efficient triangle mesh slicing algorithm for all topologies in additive manufacturing Bethany KingAllan RennieGraham Bennett ORIGINAL ARTICLE Open access 02 December 2020 Pages: 1023 - 1033
Intelligent decision-making support system for manufacturing solution recommendation in a cloud framework Alessandro SimeoneYunfeng ZengAlessandra Caggiano ORIGINAL ARTICLE Open access 03 December 2020 Pages: 1035 - 1050
Roundness prediction in centreless grinding using physics-enhanced machine learning techniques Hossein SafarzadehMarco LeonesioMichele Monno ORIGINAL ARTICLE Open access 08 December 2020 Pages: 1051 - 1063
Investigation into the surface quality and stress corrosion cracking resistance of AISI 316L stainless steel via precision end-milling operation Muhammad YasirMohd DanishMurat Sarikaya ORIGINAL ARTICLE Open access 09 December 2020 Pages: 1065 - 1076
Degradation state prediction of rolling bearings using ARX-Laguerre model and genetic algorithms Taoufik NajehJan Lundberg ORIGINAL ARTICLE Open access 10 December 2020 Pages: 1077 - 1088
Radial slicing for helical-shaped advanced manufacturing applications Nuwan MunasingheGavin Paul ORIGINAL ARTICLE 14 December 2020 Pages: 1089 - 1100
Performance of a new hybrid cutting-abrasive tool for the machining of fibre reinforced polymer composites Islam ShyhaDehong HuoMahmoud Ahmed El-Sayed ORIGINAL ARTICLE Open access 22 December 2020 Pages: 1101 - 1113
Effects of the internal structures of monolith ceramic substrates on thermal and hydraulic properties: additive manufacturing, numerical modelling and experimental testing Nikolina KovacevSheng LiKhamis Essa ORIGINAL ARTICLE Open access 28 December 2020 Pages: 1115 - 1132
The influence of soak temperature and forging lubricant on surface properties of steel forgings S. HillR. P. TurnerP. Wardle ORIGINAL ARTICLE Open access 28 December 2020 Pages: 1133 - 1144
Application and research on digital twin in electronic cam servo motion control system Jiangtao XuTongjun Guo ORIGINAL ARTICLE 02 January 2021 Pages: 1145 - 1158
The effects of locations on the build tray on the quality of specimens in powder bed additive manufacturing Snehashis PalNenad GubeljakIgor Drstvenšek ORIGINAL ARTICLE Open access 02 January 2021 Pages: 1159 - 1170
A general identification method for position-dependent geometric errors of rotary axis with single-axis driven Kai XuGuolong LiChangjiu Xia ORIGINAL ARTICLE 02 January 2021 Pages: 1171 - 1191
Cleaner milling on Ti-6Al-4V alloy cooled by liquid nitrogen: external spray and inner injection Fengbiao WangYongqing Wang ORIGINAL ARTICLE 02 January 2021 Pages: 1193 - 1206
Correction to: Efficient analysis of welding thermal conduction using the Newton–Raphson method, implicit method, and their combination Zhongyuan FengNinshu MaFenggui Lu Correction Open access 17 December 2020 Pages: 1207 - 1207