Optimization Adhesion in Cold Spraying onto Hard Substrates: A Case Study for Brass Coatings
Authors (first, second and last of 5)
Collection
Special Issue: Selected and Expanded Papers from the 2018 International Thermal Spray Conference (ITSC 2018)
Special Issue published in January 2019, Vol. 28, No. 1-2 of Journal of Thermal Spray Technology
Editors
-
Fardad Azarm
North Dakota State University, USA
-
Jan Cizek
The Czech Academy of Sciences, Czech Republic
-
Heli Koivuluoto
Tampere University of Technology, Finland
-
Yuk-Chiu Lau
GE Power and Water (retired), USA
-
Hua Li
Ningbo Institute of Materials Technology and Engineering, China
-
Filofteia-Laura Toma
Fraunhofer Institute—IWS, Germany
Articles (29 in this collection)
-
-
New Material Concepts for Thermally Sprayed Hydrodynamic Bearings
Authors (first, second and last of 7)
-
Plasma Spraying of Dense Ceramic Coating with Fully Bonded Lamellae Through Materials Design Based on the Critical Bonding Temperature Concept
Authors (first, second and last of 5)
-
-
Influence of Powder Size on the Corrosion and Wear Behavior of HVAF-Sprayed Fe-Based Coatings
Authors (first, second and last of 4)
-
An Economical Approach to Cold Spray Using In-line Nitrogen–Helium Blending
Authors (first, second and last of 4)
-
Characterization of Powder-Precursor HVOF-Sprayed Al2O3-YSZ/ZrO2 Coatings
Authors (first, second and last of 5)
-
Fabrication of Superhydrophobic Ceramic Coatings via Solution Precursor Plasma Spray Under Atmospheric and Low-Pressure Conditions
Authors (first, second and last of 4)
-
-
-
-
Characterization of Plasma-Sprayed Zirconium Coatings on Uranium Alloy Using Neutron Diffraction
Authors (first, second and last of 4)
-
Variation of Heat Input and Its Influence on Residual Stresses and Coating Properties in Arc Spraying with Different Gas Mixtures
Authors (first, second and last of 4)
-
Hybrid Suspension/Solution Precursor Plasma Spraying of a Complex Ba(Mg1/3Ta2/3)O3 Perovskite: Effects of Processing Parameters and Precursor Chemistry on Phase Formation and Decomposition
Authors (first, second and last of 5)
-
Performance Assessment of Protective Thermal Spray Coatings for Lightweight Al Brake Rotor Disks
Authors (first, second and last of 7)
-
VLPPS: An Emerging Process to Create Well-Defined Components by Additive Manufacturing
Authors (first, second and last of 8)
-
-
Modeling the Continuous Heat Generation in the Cold Spray Coating Process
Authors (first, second and last of 4)
-
Deposition Characteristics of SrZrO3 Thermal Barrier Coating Prepared by Solution Precursor Plasma Spray Process
Authors (first, second and last of 7)
-
-
Internal Diameter Coating Processes for Bond Coat (HVOF) and Thermal Barrier Coating (APS) Systems
Authors (first, second and last of 5)
-
Characterizations of Composite Titanium Nitride Coatings Deposited by Very Low-Pressure Plasma Spraying
Authors (first, second and last of 6)
-
Failure of Multilayer Suspension Plasma Sprayed Thermal Barrier Coatings in the Presence of Na2SO4 and NaCl at 900 °C
Authors (first, second and last of 7)
-
Microstructural Evolution and Sintering of Suspension Plasma-Sprayed Columnar Thermal Barrier Coatings
Authors (first, second and last of 5)
-
Corrosion and Algal Adhesion Behaviors of HVOF-Sprayed Fe-Based Amorphous Coatings for Marine Applications
Authors (first, second and last of 7)
-
-
-
Pin Fin Array Heat Sinks by Cold Spray Additive Manufacturing: Economics of Powder Recycling
Authors (first, second and last of 4)
-
Experiments, Statistical Analysis, and Modeling to Evaluate the Porosity Influence in SPS Coatings
Authors (first, second and last of 8)
