1. Cylinder of internal-combustion engine with a conical working surface

   • V. M. Gureev
   • A. M. Druzhinin
   • M. A. Zakonov

   OriginalPaper 12 March 2010 Pages: 105 - 108

2. Axial force on the screw of a single-flow high-pressure submersible pump

   • V. M. Ryazantsev
   • V. V. Plyasov

   OriginalPaper 12 March 2010 Pages: 109 - 111

3. Kinematic states of a freely moving wedge mechanism in active loading

   • A. A. Goncharov

   OriginalPaper 12 March 2010 Pages: 112 - 118

4. Stability of the initial active-surface geometry and the operational smoothness of an involute screw transmission

   • V. A. Popov

   OriginalPaper 12 March 2010 Pages: 119 - 121

5. Tractional calculations for vehicles with adaptive motors

   • I. K. Aleksandrov
   • E. V. Nesgovorov
   • V. A. Rakov

   OriginalPaper 12 March 2010 Pages: 122 - 124

6. Static balancing of rotating bodies

   • O. O. Polushkin

   OriginalPaper 12 March 2010 Pages: 125 - 127

7. Wear of frictional surfaces in high-temperature lead and lead—bismuth coolants

   • A. V. Beznosov
   • T. A. Bokova
   • V. V. Makarov

   OriginalPaper 12 March 2010 Pages: 128 - 132

8. Theory of constrained cutting: Calculating the stress-strain state in the cutting zone

   • S. I. Petrushin
   • A. V. Proskokov

   OriginalPaper 12 March 2010 Pages: 133 - 137

9. Ultrasound treatment of heat-resistant materials with compressed-air injection in the cutting zone

   • A. A. Kozlov
   • M. N. Deryabin

   OriginalPaper 12 March 2010 Pages: 138 - 140

10. Determining the optimal amplitudes and directions of ultrasound vibrations in cutting small-module gears

    • S. I. Agapov
    • I. G. Tkachenko

    OriginalPaper 12 March 2010 Pages: 141 - 143

11. Surface-layer quality in shot treatment

    • M. A. Tamarkin
    • E. E. Tishchenko
    • V. G. Lebedenko

    OriginalPaper 12 March 2010 Pages: 144 - 148

12. Development of a new theory of thermal cutting processes 2. Temperature distribution over the chip thickness

    • A. L. Vorontsov
    • N. M. Sultan-Zade
    • A. I. Savkin

    OriginalPaper 12 March 2010 Pages: 149 - 151

13. Optimal methodology for cutting studies

    • Yu. A. Novoselov

    OriginalPaper 12 March 2010 Pages: 152 - 160

14. Diagnostics of the state of a multicutter hard-alloy tool on the basis of thermoelectric phenomena in the cutting zone

    • A. L. Plotnikov
    • E. G. Krylov
    • E. M. Frolov

    OriginalPaper 12 March 2010 Pages: 161 - 165

15. Calculation of frictional self-oscillation

    • A. I. Levin
    • A. V. Ul’yanov

    OriginalPaper 12 March 2010 Pages: 166 - 169

16. Profiling in shaping screw surfaces

    • V. G. Shalamov
    • S. D. Smetanin

    OriginalPaper 12 March 2010 Pages: 170 - 172

17. Simulation of cutting-tool stress states

    • M. Sh. Migranov
    • A. A. Stepanov

    OriginalPaper 12 March 2010 Pages: 173 - 176

18. Uniform microwave heating of semifinished abrasive tools with thermoreactive organic binders

    • S. M. Mikhailin
    • A. Sh. Khusainov

    OriginalPaper 12 March 2010 Pages: 177 - 180

19. Basing precision of disk and bush blanks in multipoint machining

    • F. N. Abramov

    OriginalPaper 12 March 2010 Pages: 181 - 185

20. Applicability of P6M5 steel

    • A. M. Adaskin

    OriginalPaper 12 March 2010 Pages: 186 - 189

21. Controlled quenching of tool steels in magnetizing disperse nanosystems

    • O. A. Avdeeva
    • O. A. Grishanina
    • A. Ya. Simonovskii

    OriginalPaper 12 March 2010 Pages: 190 - 193

22. Vibration-and noise-absorbing polymer composites used in manufacturing

    • D. E. Zharin
    • S. Yu. Yurasov
    • L. N. Shafigullin

    OriginalPaper 12 March 2010 Pages: 194 - 196