Increasing the efficiency of vacuum heat treatments L. P. Karpov Heat-Treating Equipment Pages: 329 - 331
High-frequency induction salt bath with a double crucible A. N. SimonenkoE. A. Smol'nikovV. A. Shestakov Heat-Treating Equipment Pages: 332 - 333
Increasing the evenness of heating during heat treatment in vertical furnaces L. K. NagornyiV. B. Modylevskii Heat-Treating Equipment Pages: 334 - 335
Heat treatment of parts in gas-chamber furnaces with a sliding hearth V. I. MorozA. A. Astaf'evM. S. Khazanov Heat-Treating Equipment Pages: 336 - 338
Heat treatment of pipe in a dome electric furnace A. A. ZguraV. A. RudenkoV. V. Rulikov Heat-Treating Equipment Pages: 338 - 341
Modular series of electric convey or furnaces for drying and firing enamel coatings on thin-walled steel parts V. A. VilyatserL. D. DanilevskiiO. G. Musienko Heat-Treating Equipment Pages: 341 - 344
Method of measuring soot deposition in the process of steam conversion of methane A. M. DubininA. P. BaskakovV. B. Shoibonov Heat-Treating Equipment Pages: 345 - 346
Heat treatment of fasteners in production lines (from foreign technology) L. G. Satanovskii Heat-Treating Equipment Pages: 346 - 349
Structural characteristics of nickel alloys with tantalum N. N. BurovaS. B. Maslenkov Heat-Resistant Steels and Alloys Pages: 350 - 353
Phase composition of heat-resistant alloy ÉP539 G. D. Pigrova Heat-Resistant Steels and Alloys Pages: 353 - 356
Reasons for the low short-term creep resistance of alloy KhN67VMTYu at 700°C O. A. BannykhI. V. DoroninE. A. Tsukrov Heat-Resistant Steels and Alloys Pages: 357 - 358
High-Temperature ductility of heat-resistant Cr-Ni alloys A. P. GulyaevL. S. BulavinaG. S. Chernyak Heat-Resistant Steels and Alloys Pages: 358 - 363
Effect of heat treatment on the plasticity of nickel alloys K. K. BurnakovG. A. KhasinA. I. Listkova Heat-Resistant Steels and Alloys Pages: 363 - 367
Effect of various factors on the recovery and recrystallization of a nickel-base heat-resistant alloy E. E. LevinV. I. Tikhonov Heat-Resistant Steels and Alloys Pages: 367 - 371
Recrystallization of alloy KhN70MVYu V. I. RyabovV. A. Voitsekhovskii Heat-Resistant Steels and Alloys Pages: 372 - 373
Effect of rare-earth metals on the composition of nonmetallic inclusions and the heat resistance of austenitic steel V. K. FarafonovM. M. ShteinbergV. V. Voinov Heat-Resistant Steels and Alloys Pages: 374 - 377
High-temperature sulfide corrosion of nickel alloys S. B. BelikovV. V. GaidukB. S. Natapov Heat-Resistant Steels and Alloys Pages: 377 - 378
Effect of an air stream on the surface condition of heat-resistant alloys Yu. G. VekslerB. N. GuzanovV. G. Sorokin Heat-Resistant Steels and Alloys Pages: 379 - 380
Heat treatment of steam-turbine vanes restored by facing after erosion wear N. A. PogrebnoiI. A. TanankoE. M. Telesheva Heat-Resistant Steels and Alloys Pages: 381 - 382
Effect of chromium on the properties of high-strength steel 30N9K4MF V. N. ZikeevR. K. Guseinov Structural Steels Pages: 383 - 386
Effect of high purity on resistance to weakening during tempering of steel 15KhNMFA M. M. Sandomirskii Structural Steels Pages: 386 - 387
Structure and properties of steels 16G2 and 16GFR after quenching and brief tempering I. I. FrantovN. I. KarchevskayaA. V. Rudchenko Structural Steels Pages: 388 - 390
Distribution of retained austenite in the hardened layer of rolls for cold-rolling mills B. A. BrusilovskiiYu. A. GrushkoA. L. Geller Structural Steels Pages: 390 - 392
Effect of temperature on the wear resistance of steels with metastable austenite V. S. PopovN. N. BrykovG. A. Pugachev Technical Information Pages: 393 - 395
Structure of steels after high-speed plastic deformation M. V. PridantsevV. N. Kopernikova Technical Information Pages: 395 - 397
Susceptibility of low-carbon steel to brittle fracture I. N. KhristenkoYu. S. Tomenko Technical Information Pages: 398 - 399
Structure of white phases after heat treatment A. M. RozanovaL. I. Simakov Technical Information Pages: 400 - 403