Skip to main content
SpringerLink
Log in

Effect of the Addition of Waste Glass Powder along with TiC as Reinforcement on Microstructure, Wettability, Mechanical and Tribological Behavior of AZ91D Magnesium Based Alloy

  • Technical Paper
  • Published:
International Journal of Metalcasting Aims and scope Submit manuscript

Abstract

The present study investigates the effect of adding waste glass powder (WGP) along with titanium carbide (TiC) as reinforcement on the microstructure, wettability, mechanical, and tribological behavior of AZ91D magnesium-based alloy. The addition of 3 wt.% WGP and 6 wt.% TiC resulted in a refined microstructure, with the formation of good interfacial bond and a decrease in the porosity of the alloy. The wettability of the alloy was improved with the addition of reinforcements. The mechanical properties of the modified AZ91D alloy were enhanced significantly, with an increase in the hardness (51.66% improvement), fatigue strength (59.19% improvement) and ultimate tensile strength (11.9% improvement). The wear resistance of the alloy was observed to increase with the addition of WGP and TiC, owing to the formation of a protective layer on the surface of the alloy. The results suggest that the addition of WGP and TiC can improve the overall properties of AZ91D magnesium-based alloys, making them suitable for various industrial applications. Wear results showed that the resistance against wear rate of the developed composite significantly improved after the addition of the mixture of 3% Waste glass powder + 6% TiC.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13

Similar content being viewed by others

References

  1. S.P. Dwivedi, P. Pachauri, M. Maurya, A. Saxena, R. Butola, R. Sahu, S. Sharma, Alumina catalyst waste utilization for aluminum-based composites using the friction stir process. Mater. Test. 64(4), 533–540 (2022). https://doi.org/10.1515/mt-2021-2074

    Article  CAS  Google Scholar 

  2. S.P. Dwivedi, M. Petru, A. Saxena, S. Sharma, M. Mishra, A. Pramanik, S. Singh, C. Li, R.A. Ilyas, Recovery of Cr from chrome-containing leather wastes to develop aluminum-based composite material along with Al2O3 ceramic particles: an ingenious approach. Nanotechnol. Rev. 11(1), 3218–3234 (2022). https://doi.org/10.1515/ntrev-2022-0406

    Article  CAS  Google Scholar 

  3. A. Kumar, M. Kumar, P.C. Verma, Ranking analysis of AA7075–Cr alloy composites based on physical, mechanical, and sliding wear assessment using hybrid ENTROPY-VIKOR approach. Int. J. Metalcast. (2023). https://doi.org/10.1007/s40962-023-00988-w

    Article  Google Scholar 

  4. A. Kumar, M. Kumar, Investigations on physical, mechanical and sliding wear assessment of ZA27-Gr alloy composites using preference selection index method. Int. J. Metalcast. (2023). https://doi.org/10.1007/s40962-022-00953-z

    Article  Google Scholar 

  5. S.P. Dwivedi, S. Sharma, Recovery of Al2O3/Al powder from aluminum dross to utilize as reinforcement along with graphene in the synthesis of aluminum-based composite. Part. Sci. Technol. (2023). https://doi.org/10.1080/02726351.2023.2190049

    Article  Google Scholar 

  6. S.P. Dwivedi, Effect of ball-milled MgO and Si3N4 addition on the physical, mechanical and thermal behaviour of aluminium based composite developed by hybrid casting technique. Int. J. Cast Met. Res. 33, 35–49 (2020). https://doi.org/10.1080/13640461.2020.1744370

    Article  CAS  Google Scholar 

  7. X. Zhang, T. Li, H. Teng, S. Xie, J. Jin, Semisolid processing AZ91 magnesium alloy by electromagnetic stirring after near-liquidus isothermal heat treatment. Mater. Sci. Eng. A 475, 194–201 (2008). https://doi.org/10.1016/j.msea.2007.04.049

    Article  CAS  Google Scholar 

  8. Y.D. Yu, C.X. Li, The effect of alternative low frequency electromagnetic field on the solidification microstructure and mechanical properties of ZK60 alloys. Mater. Des. 44, 17–22 (2013). https://doi.org/10.1016/j.matdes.2012.07.034

    Article  CAS  Google Scholar 

  9. T.Y. Kwaka, W.J. Kim, Hot compression behavior of the 1wt.% calcium containing Mg–8Al–05Zn (AZ80) alloy fabricated using electromagnetic casting technology. Mater. Sci. Eng. A 615, 222–230 (2014). https://doi.org/10.1016/j.msea.2014.07.025

    Article  CAS  Google Scholar 

  10. L. Bao, Z. Zhang, Q. Le, L. Ru, J. Cui, Heat transfer behavior of AZ80–1%Y alloy during low-frequency electromagnetic casting. Trans. Nonferrous Met. Soc. China 25, 3618–3624 (2015). https://doi.org/10.1016/S1003-6326(15)64003-1

    Article  CAS  Google Scholar 

  11. J.H. Li, J. Barrirero, G. Sha, H. Aboulfadl, F. Mücklich, P. Schumacher, Precipitation hardening of an Mg–5Zn–2Gd–0.4Zr (wt.%) alloy. Acta Mater. 108, 207–218 (2016). https://doi.org/10.1016/j.actamat.2016.01.053

    Article  CAS  Google Scholar 

  12. Xu. Qiong, Y. Li, H. Ding, A. Ma, J. Jiang, G. Chen, Y. Chen, Microstructure and mechanical properties of SiCp/AZ91 composites processed by a combined processing method of equal channel angular pressing and rolling. J. Mater. Res. 15, 5244–5251 (2021). https://doi.org/10.1016/j.jmrt.2021.11.005

    Article  CAS  Google Scholar 

  13. G.U.A.N. Zhi-ping, L.I. Ming-yu, X.I.A. Kai-xin, L.I. Zhi-gang, G.A.O. Dan, Z.H.A.O. Po, M.A. Pin-kui, S.O.N.G. Jia-wang, Microstructure, mechanical properties and wear resistance of SiCp/AZ91 composite prepared by vacuum pressure infiltration. Trans. Nonferrous Met. Soc. China 32(1), 104–121 (2022). https://doi.org/10.1016/S1003-6326(21)65781-3

    Article  Google Scholar 

  14. P. Emadi, B. Andilab, C. Ravindran, Processing and properties of magnesium-based composites reinforced with low levels of Al2O3. Int. Metalcast. (2022). https://doi.org/10.1007/s40962-021-00738-w

    Article  Google Scholar 

  15. E. Cevik, M. Gundogan, Dry sliding wear behavior of (GNPs + TiB2)-reinforced AZ91 magnesium matrix hybrid composites produced by pressure infiltration casting method. Int. Metalcast. 15, 1250–1259 (2021). https://doi.org/10.1007/s40962-020-00552-w

    Article  Google Scholar 

  16. A. Kumar, S. Kumar, N.K. Mukhopadhyay et al., Effect of TiC reinforcement on mechanical and wear properties of AZ91 matrix composites. Int. Metalcast. 16, 2128–2143 (2022). https://doi.org/10.1007/s40962-021-00747-9

    Article  CAS  Google Scholar 

  17. H. Mohammadi, M. Emamy, Z. Hamnabard, The statistical analysis of tensile and compression properties of the as-cast AZ91-X%B4C composites. Int. Metalcast. 14, 505–517 (2020). https://doi.org/10.1007/s40962-019-00377-2

    Article  CAS  Google Scholar 

  18. M. Khorasanian, M. Yeganeh, N. Gholamzadeh et al., Effect of addition of silver and chilled casting on corrosion behavior of AZ91 magnesium alloy. Int. Metalcast. (2021). https://doi.org/10.1007/s40962-020-00558-4

    Article  Google Scholar 

  19. S. Banerjee, S. Poria, G. Sutradhar et al., Nano-indentation and corrosion characteristics of ultrasonic vibration assisted stir-cast AZ31–WC–graphite nano-composites. Int. Metalcast. (2020). https://doi.org/10.1007/s40962-020-00538-8

    Article  Google Scholar 

  20. H. Zengin, Role of Sr in Microstructure, hardness and biodegradable behavior of cast Mg–2Zn–2Ca–0.5Mn (ZXM220) alloy for potential implant application. Int. Metalcast. 14, 442–453 (2020). https://doi.org/10.1007/s40962-019-00366-5

    Article  CAS  Google Scholar 

  21. J. Bian, B. Yu, L. Jiang et al., Research on the effect of Sr and Zr on microstructure and properties of Mg–4Zn alloy. Int. Metalcast. (2021). https://doi.org/10.1007/s40962-021-00576-w

    Article  Google Scholar 

  22. A. Incesu, A. Gungor, Biocorrosion and mechanical properties of ZXM100 and ZXM120 magnesium alloys. Int. Metalcast. 13, 905–914 (2019)

    Article  CAS  Google Scholar 

  23. A. Kumar, A. Patnaik, I.K. Bhat, Investigation of nickel metal powder on tribological and mechanical properties of Al-7075 alloy composites for gear materials. Powder Metall. 60(5), 371–383 (2017)

    Article  CAS  Google Scholar 

  24. A. Kumar, A. Patnaik, I.K. Bhat, Tribology analysis of cobalt particulate filled Al 7075 alloy for gear materials: a comparative study. Silicon 11, 1295–1311 (2019)

    Article  CAS  Google Scholar 

  25. S.P. Dwivedi, A.K. Srivastava, Utilization of chrome containing leather waste in development of aluminium based green composite material. Int. J. Precis. Eng. Manuf. Green Technol. 7, 781–790 (2020). https://doi.org/10.1007/s40684-019-00179-1

    Article  Google Scholar 

  26. S.P. Dwivedi, R. Sahu, Development of aluminum-based composite material by using bagasse ash and eggshell as reinforcement along with nano-CuO particles. J. Inst. Eng. India Ser. D (2022). https://doi.org/10.1007/s40033-022-00417-y

    Article  Google Scholar 

  27. R. Yadav, S. Dwivedi, V. Dwivedi, Synthesis and mechanical behavior of Ball–Milled Agro–Waste RHA and eggshell reinforced composite material. Mater. Perform. Charact. 10(1), 237–254 (2021). https://doi.org/10.1520/MPC20190247

    Article  CAS  Google Scholar 

  28. O.S. Adesina, A.A. Akinwande, A.A. Adediran, O.A. Balogun, O.O. Sanyaolu, V. Romanovski, Morphological evolution and strength performance of green-aluminium-7075 hybrid composites modeled by response surface analysis. Multiscale Multidiscip. Model. Exp. Des. (2023). https://doi.org/10.1007/s41939-023-00162-z

    Article  Google Scholar 

  29. W. Jiang, J. Zhu, G. Li, F. Guan, Y. Yu, Z. Fan, Enhanced mechanical properties of 6082 aluminum alloy via SiC addition combined with squeeze casting. J. Mater. Sci. Technol. 88, 119–131 (2021)

    Article  CAS  Google Scholar 

  30. J. Zhu, W. Jiang, G. Li, F. Guan, Y. Yu, Z. Fan, Microstructure and mechanical properties of SiCnp/Al6082 aluminum matrix composites prepared by squeeze casting combined with stir casting. J. Mater. Process. Technol. 283, 116699 (2020)

    Article  CAS  Google Scholar 

  31. A. Kumar, M. Kumar, S. Gothwal, P. Srivastava, Analysis of the sliding wear (experimental and modeling validation), thermal, thermo-mechanical, and fracture performance of AA7075-chromium alloy composites. J. Bio Tribo Corros. 8(4), 107 (2022)

    Article  Google Scholar 

  32. M. Kumar, R. Kumar, S. Bhaskar, A. Kumar, S. Harizan, Parametric optimization and ranking analysis of hybrid AA2024–SiC/Si3N4 alloy composites based on mechanical and sliding wear performance. J. Bio Tribo Corros. 8(1), 24 (2022)

    Article  Google Scholar 

  33. A. Kumar, M. Kumar, A.K. Tiwari, Analysis of mechanical and sliding wear performance of hybrid AA7075–SiC/Gr/Cu alloy composites fabricated by high vacuum stir casting process. J. Bio Tribo Corros. 8(1), 12 (2022)

    Article  Google Scholar 

  34. A. Kumar, M. Kumar, B. Pandey, Investigations on mechanical and sliding wear performance of AA7075–SiC/marble dust/graphite hybrid alloy composites using hybrid ENTROPY–VIKOR method. Silicon 14(5), 2051–2065 (2022)

    Article  CAS  Google Scholar 

  35. A. Kumar, M. Kumar, Fracture toughness and thermal investigations of Al 7075—cobalt particulates reinforced alloy composites prepared using high vacuum casting method for gear applications: proposed thermal conductivity and fracture toughness modeling. Int. J. Metalcast. (2022). https://doi.org/10.1007/s40962-022-00901-x

    Article  Google Scholar 

  36. M. Kumar, R. Kumar, S. Bhaskar, A. Kumar, Parametric optimization and ranking analysis of AA2024−Al2O3/AlN alloy composites fabricated via stir casting route under dry sliding wear investigation. Int. J. Metalcast. (2023). https://doi.org/10.1007/s40962-023-01053-2

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Lloyd Institute of Engineering & Technology, Knowledge Park II, Greater Noida, Uttar Pradesh, 201306, India

    Shashi Prakash Dwivedi

  2. Mechanical Engineering Department, Amity School of Engineering and Technology, Amity University Noida, Uttar Pradesh, Sector 125, Noida, Uttar Pradesh, 201301, India

    Vijay Chaudhary

  3. Mechanical Engineering Department, University Centre for Research and Development, Chandigarh University, Mohali, Punjab, 140413, India

    Shubham Sharma

Authors
  1. Shashi Prakash Dwivedi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Vijay Chaudhary
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Shubham Sharma
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Shashi Prakash Dwivedi.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Dwivedi, S.P., Chaudhary, V. & Sharma, S. Effect of the Addition of Waste Glass Powder along with TiC as Reinforcement on Microstructure, Wettability, Mechanical and Tribological Behavior of AZ91D Magnesium Based Alloy. Inter Metalcast 18, 1387–1400 (2024). https://doi.org/10.1007/s40962-023-01117-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40962-023-01117-3

Keywords

Search

Navigation