1. Introduction

   • Yu Zou
   • Hang Yu
   • Matteo Seita

   Invited Review 01 August 2020 Pages: 1899 - 1899

2. Experimental and numerical investigation of selective laser melting–induced defects in Ti–6Al–4V octet truss lattice material: the role of material microstructure and morphological variations

   • Asma El Elmi
   • David Melancon
   • Damiano Pasini

   Invited Papers 01 August 2020 Pages: 1900 - 1912

   

3. Additively manufactured copper matrix composites: Heterogeneous microstructures and combined strengthening effects

   • Heng Ouyang
   • Ge Wang
   • Qiang Guo

   Invited Papers 01 August 2020 Pages: 1913 - 1921

   

4. Cost-affordable, high-performance Ti–TiB composite for selective laser melting additive manufacturing

   • Yangping Dong
   • Yulong Li
   • Ming Yan

   Invited Papers 01 August 2020 Pages: 1922 - 1935

   

5. Quantitative microstructure analysis for solid-state metal additive manufacturing via deep learning

   • Yi Han
   • R. Joey Griffiths
   • Yunhui Zhu

   Invited Papers 01 August 2020 Pages: 1936 - 1948

   

6. Effect of heat treatment on the modification of microstructure of selective laser melted (SLM) IN718 and its consequences on mechanical behavior

   • R. J. Vikram
   • Anubhav Singh
   • Satyam Suwas

   Article 01 August 2020 Pages: 1949 - 1962

   

7. Materials and manufacturing renaissance: Additive manufacturing of high-entropy alloys

   • Jinyeon Kim
   • Akane Wakai
   • Atieh Moridi

   Invited Review 01 August 2020 Pages: 1963 - 1983

   

8. Deformation mechanisms and defect tolerance in the microstructure of 3D-printed alloys

   • Matthew Moneghan
   • Christopher Williams
   • Reza Mirzaeifar

   Article 01 August 2020 Pages: 1984 - 1997

   

9. Selective laser melting of graphene oxide–reinforced Ti–48Al–2Cr–2Nb: Improved manufacturability and mechanical strength

   • Xing Zhang
   • Bo Mao
   • Yufeng Zheng

   Article 01 August 2020 Pages: 1998 - 2005

   

10. Microstructure and properties of a novel wear- and corrosion-resistant stainless steel fabricated by laser melting deposition

    • Yurou Han
    • Chunhua Zhang
    • Adil Othman Abdullah

    Article 01 August 2020 Pages: 2006 - 2015

    

11. Preparation, microstructure, and microhardness of selective laser-melted W–3Ta sample

    • Junfeng Li
    • Zhengying Wei
    • Zhenzhong Sun

    Article 01 August 2020 Pages: 2016 - 2024

    

12. Influence of selective laser melting scanning speed parameter on the surface morphology, surface roughness, and micropores for manufactured Ti6Al4V parts

    • Mohd Faizal Sadali
    • Mohamad Zaki Hassan
    • Zainudin A Rasid

    Article 01 August 2020 Pages: 2025 - 2035

    

13. A comparative investigation of long-term oxidation behavior of selective laser melting–fabricated Inconel 718 at 650 °C

    • Yan-Wen Luo
    • Bin Zhang
    • Guang-Ping Zhang

    Article 01 August 2020 Pages: 2036 - 2045

    

14. Build orientation optimization for lightweight lattice parts production in selective laser melting by using a multicriteria genetic algorithm

    • Renkai Huang
    • Ning Dai
    • Xiaosheng Cheng

    Article 01 August 2020 Pages: 2046 - 2054

    

15. Towards understanding side-skin surface characteristics in laser powder bed fusion

    • Sagar Patel
    • Allan Rogalsky
    • Mihaela Vlasea

    Invited Paper 01 August 2020 Pages: 2055 - 2064

    

16. Microstructural heterogeneity and mechanical anisotropy of 18Ni-330 maraging steel fabricated by selective laser melting: The effect of build orientation and height

    • Yi Yao
    • Kaiwen Wang
    • Feng Yan

    Article 01 August 2020 Pages: 2065 - 2076