Abstract
The silicone rubber mold (SRM) has large applications for the pilot runs in the mold industry because it is capable of reducing the cost and time in a new product development phase. However, the cooling performance in the cooling stage is not acceptable after the injection molding due to low thermal conductivity of this material. To improve the cooling performance, five different fillers were added into the silicone rubber (SR) to develop SRM with better cooling performance in the cooling stage after injection molding. It was found that the alcohol used to remove the polyvinyl butyral resin cooling channels is less volatile, environmentally friendly, and less harmful to the operator compared with conventional method using acetone to remove the acrylonitrile butadiene styrene cooling channels. The cooling time of the molded wax pattern can be saved by 42.7%, 53.8%, 45.7%, 50.9%, and 16.7% for SRM with 60 wt.% Al, 80 wt.% Fe, 70 wt.% Cu, 25 wt.% graphite (G), and 20 wt.% carbon black powders compared with that for SRM without any fillers. The SR filled with 20 wt.% G powder seems to be the optimal method for producing an SRM with better cooling performance based on the heat transfer coefficient, production cost, and production yield of SRM.
Similar content being viewed by others
References
Armillotta A, Baraggi R, Fasoli S (2017) SLM tooling for die casting with conformal cooling channels. Int J Adv Manuf Technol 71(1–4):573–583
Kuo CC, You ZY (2018) Development of injection molding tooling with conformal cooling channels fabricated by optimal process parameters. Int J Adv Manuf Technol 96(1–4):1003–1013
Kuo CC, Lyu SY (2018) A cost-effective approach using recycled materials to fabricate micro-hot embossing die for microfabrication. Int J Adv Manuf Technol 94(9–12):4365–4371
Kuo CC, Chen WH, Liu XZ, Liao YL, Chen WJ, Huang BY, Tsai RL (2017) Development of a low-cost wax injection mold with high cooling efficiency. Int J Adv Manuf Technol 93(5–8):2081–2088
Kuo CC, Chen WH, Zhang JW, Tsai DA, Cao YL (2017) A new method of manufacturing a rapid tooling with different cross-sectional cooling channels. Int J Adv Manuf Technol 92(9–12):3481–3487
Kuo CC, Li MR (2017) Development of sheet metal forming dies with excellent mechanical properties using additive manufacturing and rapid tooling technologies. Int J Adv Manuf Technol 90(1):21–25
Du ZH, Chua CK, Chua YS, Loh-Lee KG, Lim ST (2002) Rapid sheet metal manufacturing. Part 1: indirect rapid tooling. Int J Adv Manuf Technol 19(6):411–417
Chong L, Ramakrishna S, Singh S (2018) A review of digital manufacturing-based hybrid additive manufacturing processes. Int J Adv Manuf Technol 95(5–8):2281–2300
Leal R, Barreiros FM, Alves L, Romeiro F, Vasco JC, Santos M, Marto C (2017) Additive manufacturing tooling for the automotive industry. Int J Adv Manuf Technol 92(5–8):1671–1676
Thomas D (2016) Costs, benefits, and adoption of additive manufacturing: a supply chain perspective. Int J Adv Manuf Technol 85(5–8):1857–1876
Maji PK, Banerjee PS, Sinha A (2008) Application of rapid prototyping and rapid tooling for development of patient-specific craniofacial implant: an investigative study. Int J Adv Manuf Technol 36(5–6):510–515
He Z, Lu B, Hong J, Wang Y, Tang Y (2007) A novel arc-spraying robot for rapid tooling. Int J Adv Manuf Technol 31(9–10):1012–1020
Rajaguru J, Duke M, Au C (2015) Development of rapid tooling by rapid prototyping technology and electroless nickel plating for low-volume production of plastic parts. Int J Adv Manuf Technol 78(1–4):31–40
M. Issa, D. Petkovic, N. D. Pavlovic, L. Zentner, Sensor elements made of conductive silicone rubber for passively compliant gripper, The International Journal of Advanced Manufacturing Technology, Volume 69, Issue 5–8, 2013, Pages 1527–1536
Yuan B, Wang Z, Fang W, Li J (2018) Rheological experimental properties and numerical modeling of a pressure-transmitting silicone rubber used in sheet metal flexible-die forming. Int J Adv Manuf Technol 95(5–8):1697–1714
Ou H, Sahli M, Barrière T, Gelin JC (2017) Multiphysics modelling and experimental investigations of the filling and curing phases of bi-injection moulding of thermoplastic polymer/liquid silicone rubbers. Int J Adv Manuf Technol 92(9–12):3871–3882
Ou H, Sahli M, Barriere T, Gelin JC (2017) Experimental characterisation and modelling of rheokinetic properties of different silicone elastomers. Int J Adv Manuf Technol 92(9–12):4199–4211
Yang G, Makarova OV, Amstutz P, Tang CM (2008) Rapid replication of powder composite high-aspect-ratio microstructures using silicone rubber micromolds. Microsyst Technol 14(9–11):1663–1667
Thian SCH, Fuh JYH, Wong YS, Loh HT, Gian PW, Tang Y (2008) Fabrication of microfluidic channel utilizing silicone rubber with vacuum casting. Microsyst Technol 14(8):1125–1135
Glocker D, Wiseman R (1982) A new method for the batch production of micro-Fresnel zone plates. J Vac Sci Technol 20(4):1098–1100
Christian P, Jones IA, Rudd CD, Campbell RI, Corden TJ (2001) Monomer transfer moulding and rapid prototyping methods for fibre reinforced thermoplastics for medical applications. Compos A: Appl Sci Manuf 32(7):969–976
L.S. Ching, C.C. Kai, C.S. Meng, A novel technique for fabricating facial prosthetic model, Medicine and Biology Society, Proceedings of the 20th Annual International Conference of the IEEE Engineering in Medicine and Biology Society, Volume 20, Number 5, 1998, Pages 2746–2749
Reggiani B, Todaro I (2019) Investigation on the design of a novel selective laser melted insert for extrusion dies with conformal cooling channels, Volume 104. Int J Adv Manuf Technol:815–830
Kitayama S, Miyakawa H, Takano M, Aiba S (2017) Multi-objective optimization of injection molding process parameters for short cycle time and warpage reduction using conformal cooling channel. Int J Adv Manuf Technol 88(5–8):1735–1744
Holker R, Tekkaya AE (2016) Advancements in the manufacturing of dies for hot aluminum extrusion with conformal cooling channels. Int J Adv Manuf Technol 83(5–8):1209–1220
Lim WS, Choi HS, Ahn SY, Kim BM (2014) Cooling channel design of hot stamping tools for uniform high-strength components in hot stamping process. Int J Adv Manuf Technol 70(5–8):1189–1203
Wang X, Li Z, Gu J, Ruan S, Shen C, Wang X (2016) Reducing service stress of the injection-molded polycarbonate window by optimizing mold construction and product structure. Int J Adv Manuf Technol 86(5–8):1691–1704
Brooks H, Brigden K (2016) Design of conformal cooling layers with self-supporting lattices for additively manufactured tooling. Addit Manuf 11:16–22
Vojnová E (2016) The benefits of a conforming cooling systems the molds in injection moulding process. Procedia Engineering 149:535–543
Kuo CC, Chen WH, Xu WC (2017) A cost-effective approach for rapid manufacturing wax injection molds with complex geometrical shapes of cooling channels. Int J Adv Manuf Technol 91(5–8):1689–1695
Kuo CC, Xu WC (2018) Effects of different cooling channels on the cooling efficiency in the wax injection molding process. Int J Adv Manuf Technol 98(1–4):887–895
Kuo CC, Chen WH, Liu XZ, Liao YL, Chen WJ, Huang BY, Tsai RL (2017) Development of a low-cost wax injection mold with high cooling efficiency. Int J Adv Manuf Technol 93(5–8):2081–2088
Wu J, Zhang C, Su B, Dong J, Wang Y, Gond BK (2018) New method for studying the macro-micro contact properties between smooth metal and silicone rubber. Int J Adv Manuf Technol 96(5–8):1761–1767
Kuo CC, Wu MX (2017) Evaluation of service life of silicone rubber molds using vacuum casting. Int J Adv Manuf Technol 90(9–12):3775–3781
Hsu FH, Wang K, Huang CT, Chang RY (2013) Investigation on conformal cooling system design in injection molding. Adv Prod Eng Manag 8(2):107–115
Chiaroni AB, Silveira ZC (2019) Experimental and numerical evaluation of the temperature profile of a modular extrusion head applied to an experimental 3D printer. Int J Adv Manuf Technol 103(9–12):4385–4398
Stachurski W, Sawicki J, Krupanek K, Nadolny K (2019) Numerical analysis of coolant flow in the grinding zone. Int J Adv Manuf Technol 104:1999–2012
M. Hajinezhad, A. Azizi, Numerical analysis of effect of coolant on the transient temperature in underwater friction stir welding of Al6061-T6, Int J Adv Manuf Technol, 2016, Volume 83, Issue 5–8, Pages 1241–1252
Belhocine A, Abdullah OI (2019) Numerical simulation of thermally developing turbulent flow through a cylindrical tube. Int J Adv Manuf Technol 102(5–8):2001–2012
Kuo CC, Jiang ZF (2019) Numerical and experimental investigations of a conformally cooled maraging steel injection molding tool fabricated by direct metal printing. Int J Adv Manuf Technol 104(9–12):4169–4181
Huang PH, Shih LK-L, Lin HM, Chu CI, Chou CS (2019) Novel approach to investment casting of heat-resistant steel turbine blades for aircraft engines. Int J Adv Manuf Technol 104:2911–2923
Uyor UO, Omah AD, Aigbodion VS, Ezema IC, Nwoke OA (2019) Effects of carbonized particles on microstructure and mechanical properties of epoxy resin. Int J Adv Manuf Technol 103(9–12):4283–4292
Kuo CC, Wang YJ (2017) Optimization of plasma surface modification parameter for fabricating a hot embossing mold with high surface finish. Int J Adv Manuf Technol 91(9–12):3363–3369
Kuo CC, Lyu SY (2017) Development of low-cost hot embossing stamps with long lifespan and environmental protection. Int J Adv Manuf Technol 91(5–8):1889–1895
Darshan C, Jain S, Dogra M, Gupta MK, Mia M, Haque R (2019) Influence of dry and solid lubricant-assisted MQL cooling conditions on the machinability of Inconel 718 alloy with textured tool. Int J Adv Manuf Technol 105:1835–1849
Jia D, Li C, Zhang Y, Zhang D, Zhang X (2016) Experimental research on the influence of the jet parameters of minimum quantity lubrication on the lubricating property of Ni-based alloy grinding. Int J Adv Manuf Technol 82(1–4):617–630
Wojtewicz M, Nadolny K, Kapłonek W, Rokosz K, Matýsek D, Ungureanu M (2019) Experimental studies using minimum quantity cooling (MQC) with molybdenum disulfide and graphite-based microfluids in grinding of Inconel® alloy 718. Int J Adv Manuf Technol 101(1–4):637–661
Abdo BMA, El-Tamimi AM, Anwar S, Umer U, Alahmari AM, Ghaleb MA (2018) Experimental investigation and multi-objective optimization of Nd:YAG laser micro-channeling process of zirconia dental ceramic. Int J Adv Manuf Technol 98(5–8):2213–2230
Yang M, Li C, Zhang Y, Jia D, Li R, Hou Y, Cao H (2019) Effect of friction coefficient on chip thickness models in ductile-regime grinding of zirconia ceramics. Int J Adv Manuf Technol 102(5–8):2617–2632
Xu S, Yao Z, Cai H, Wang H (2017) An experimental investigation of grinding force and energy in laser thermal shock-assisted grinding of zirconia ceramics. Int J Adv Manuf Technol 91(9–12):3299–3306
Kim TW, Lee CM (2015) A study on the development of milling process for silicon nitride using ball end-mill tools by laser-assisted machining. Int J Adv Manuf Technol 77(5–8):1205–1211
Azarhoushang B, Soltani B, Zahedi A (2017) Laser-assisted grinding of silicon nitride by picosecond laser. Int J Adv Manuf Technol 93(5–8):2517–2529
Laouissi A, Yallese MA, Belbah A, Belhadi S, Haddad A (2019) Investigation, modeling, and optimization of cutting parameters in turning of gray cast iron using coated and uncoated silicon nitride ceramic tools. Based on ANN, RSM, and GA optimization. Int J Adv Manuf Technol 101(1–4):523–548
Wei H, Hussain G, Iqbal A, Zhang ZP (2019) Surface roughness as the function of friction indicator and an important parameters-combination having controlling influence on the roughness: recent results in incremental forming. Int J Adv Manuf Technol 101:2533–2545
Saad MS, Nor AM, Baharudin ME, Zakaria MZ, Aiman AF (2019) Optimization of surface roughness in FDM 3D printer using response surface methodology, particle swarm optimization, and symbiotic organism search algorithms. Int J Adv Manuf Technol 105:5121–5137
Su H, Yang C, Gao S, Fu Y, Ding W (2019) A predictive model on surface roughness during internal traverse grinding of small holes. Int J Adv Manuf Technol 103:2069–2077
Jin SY, Pramanik A, Basak AK, Prakash C, Shankar S, Debnath S (2020) Burr formation and its treatments—a review. Int J Adv Manuf Technol 107:2189–2210. https://doi.org/10.1007/s00170-020-05203-2
Munhoz MR, Dias LG, Breganon R, Ribeiro FSF, de Souza Gonçalves JF, Hashimoto EM, da Silva Júnior CE (2020) Analysis of the surface roughness obtained by the abrasive flow machining process using an abrasive paste with oiticica oil. Int J Adv Manuf Technol 106:5061–5070
Dong G, Marleau-Finley J, Zhao YF (2019) Investigation of electrochemical post-processing procedure for Ti-6Al-4V lattice structure manufactured by direct metal laser sintering (DMLS). Int J Adv Manuf Technol 104:3401–3417
Tyagi P, Goulet T, Riso C, Garcia-Moreno F (2019) Reducing surface roughness by chemical polishing of additively manufactured 3D printed 316 stainless steel components. Int J Adv Manuf Technol 100:2895–2900
Nagalingam AP, Yeo SH (2018) Effects of ambient pressure and fluid temperature in ultrasonic cavitation machining. Int J Adv Manuf Technol 98:2883–2894
Yung KC, Zhang SS, Duan L, Choy HS, Cai ZX (2019) Laser polishing of additive manufactured tool steel components using pulsed or continuous-wave lasers. Int J Adv Manuf Technol 105:425–440
Prapamonthon P, Yin B, Yang G, Zhang M (2019) Understanding of temperature and cooling effectiveness sensitivity of a film-cooled vane under coolant inlet temperature effect: a case study. Case Stud Therm Eng 14:100505
Wu S, Bi J, Li Z, Liao H, Wang C, Zheng L (2020) Feasibility study of oil-on-water cooling in high-speed end milling of hardened steel. Int J Adv Manuf Technol 107:271–292
Vashisht R, Kapila A (2014) A comparative study of coolants based on the cooling time of injection molding. Int J Emerg Technol Adv Eng 4(6):830–834
Zhou M, Kong L, Xie L, Fu T, Jiang G, Feng Q (2017) Design and optimization of non-circular mortar nozzles using finite volume method and Taguchi method. Int J Adv Manuf Technol 90(9–12):3543–3553
Chen WC, Nguyen MH, Chiu WH, Chen TN, Tai PH (2016) Optimization of the plastic injection molding process using the Taguchi method, RSM, and hybrid GA-PSO. Int J Adv Manuf Technol 83(9–12):1873–1886
Adnan MF, AbdullahE AB, Samad Z (2017) Springback behavior of AA6061 with non-uniform thickness section using Taguchi method, The International Journal of Advanced Manufacturing Technology. 89(5–8):2041–2052
Pinar AM, Filiz S, Ünlü BS (2016) A comparison of cooling methods in the pocket milling of AA5083-H36 alloy via Taguchi method. Int J Adv Manuf Technol 83(9–12):1431–1440
Gong G, Chen JC, Guo G (2017) Enhancing tensile strength of injection molded fiber reinforced composites using the Taguchi-based six sigma approach. Int J Adv Manuf Technol 91(9–12):3385–3393
Funding
The authors received financial support from the Ministry of Science and Technology of Taiwan under contract nos. MOST107-2221-E-131-018, MOST 106-2221-E-131-010, MOST 106-2221-E-131-011, and MOST 105-2221-E-131-012.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Kuo, CC., Chen, WH., Lin, YX. et al. Effects of different fillers on the silicone rubber mold with conformal cooling channels. Int J Adv Manuf Technol 108, 1509–1525 (2020). https://doi.org/10.1007/s00170-020-05508-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-020-05508-2