Abstract
Using a mass-loss method, we investigated the solubility change of gallium nitride (GaN) in supercritical ammonia with mixed mineralizers [ammonium chloride (NH4Cl) + ammonium bromide (NH4Br) and NH4Cl + ammonium iodide (NH4I)]. The solubilities were measured over the temperature range 450–550 °C, at 100 MPa. The solubility increased with NH4Cl mole fraction at 450 °C and 100 MPa. The temperature dependence of the solubility curve was then measured at an equal mole ratio of the two mineralizers. The slope of the solubility–temperature relationship in the mixed mineralizer was between those of the individual mineralizers. These results show that the temperature dependence of the solubility of GaN can be controlled by the mineralizer mixture ratio. The results of the van’t Hoff plot suggest that the solubility species were unchanged over the investigated temperature range. Our approach might pave the way to realizing large, high-quality GaN crystals for future gallium-nitride electronic devices, which are increasingly on demand in the information-based age.
Similar content being viewed by others
Introduction
In an increasingly information-based society, high-speed wireless communications systems with massive information-transmission capability are expected as a ubiquitous network technology in the near future. However, to realize such systems, the power and operating frequency of electronic devices need to be increased. Gallium-nitride devices offer a promising solution, as their power and frequency is expected to exceed those of Si-based devices. However, these devices require a large-diameter, high-quality GaN bulk single-crystal substrate, which does not yet exist. Although heteroepitaxial growth can be carried out on sapphire substrate by the hydride vapor phase epitaxy (HVPE) method, the lattice mismatch increases the dislocation density of the growth. For this reason, there has been a race to develop bulk GaN single-crystal substrates using various methods. Single-crystal GaN is mainly grown by the Na flux method [1, 2] or the ammonothermal method [3,4,5,6,7,8,9,10,11]. The ammonothermal method is promising for its relatively mild crystal growth conditions and the ease of up-scaling the equipment.
Previously, we reported a GaN crystal growth rate exceeding the minimum requirements of industrial application (100 μm/day) using the ammonothermal method with NH4I as the mineralizer [7]. However, because the GaN solubility rapidly increases around 530 °C, the supersaturation level was difficult to control by this approach [12]. Although supersaturation is a driving force for crystal growth, spontaneous nucleation overcomes crystal growth under excessive supersaturation conditions. In fact, when NH4I is used as the mineralizer, a large number of needle crystals are deposited on the inner wall of the autoclave [13]. Changing the temperature difference between the raw material dissolution region and the crystal growth region, the type of mineralizer, and other factors can control the supersaturation level. Controlling the temperature dependence of GaN solubility by altering the mineralizer-mixing ratio would be very useful for ammonothermal crystal growth, because mineralizer addition is an easily adjustable parameter.
Several researchers have measured the solubility of GaN in supercritical ammonia with a single mineralizer [12, 14,15,16,17,18,19]. However, the solubility of GaN in supercritical ammonia with mixed mineralizers has not been reported yet. Thus, the present study investigates the change in the solubility of GaN in supercritical ammonia under addition of a mixed mineralizer, and whether the mixing ratio can control the temperature dependence of the solubility.
Materials and methods
GaN crystals were grown by HVPE. The mineralizers NH4Cl (purity 99.5%), NH4Br (purity 99.0%), and NH4I (purity 99.5%) were purchased from Wako Pure Chemical Industries (Japan), and dried at 100 °C for 24 h before use. Ammonia (NH3, purity 99.999%) was obtained from Japan Fine Products Co. Ltd (Japan).
The solubility was measured by the mass-loss method, as described in our previous paper [18]. The uncertainties in the temperature and pressure values were ± 2 °C and ± 2 MPa, respectively. The composition of the sample mixtures was determined by weighing the chemicals at the desired molar ratio. The estimated measurement uncertainty in the solubility was within ± 10%.
Results
The measured solubilities of GaN in supercritical ammonia with mixed mineralizer compositions of NH4Cl + NH4Br and NH4Cl + NH4I are given in Tables 1 and 2. Panels (a) and (b) of Fig. 1 show the mineralizer-composition dependence of the GaN solubility in supercritical ammonia in the presence of NH4Cl + NH4Br and NH4Cl + NH4I, respectively. In both systems, the temperature and pressure were 450 °C and 100 MPa respectively, and the mixed-mineralizer concentration was 3.1 mol%. In the NH4Cl + NH4Br mixture, the GaN solubility curve became gradually convex with increasing molar fraction of NH4Cl, but in the NH4Cl + NH4I mineralizer, it was an almost-linear function of NH4Cl molar fraction.
Next, we investigated the temperature dependence of the solubility curve in a 1:1 molar ratio mixture. The results for the NH4Cl + NH4Br and NH4Cl + NH4I systems are shown in panels (a) and (b) of Fig. 2, respectively. The curve for the NH4Cl + NH4Br system lies between those of the single NH4Cl and NH4Br mineralizers. Similarly, the curve of the NH4Cl + NH4I system almost lies between those of the single NH4Cl and NH4I mineralizers.
Temperature dependence of GaN solubility in supercritical ammonia with different mineralizers (100 MPa, 3.1 ± 0.1% mineralizer): NH4Cl, circle (from previous work [18]); NH4Br, square (from previous work [12]); NH4I, triangle (from previous work [12]); NH4Cl + NH4Br (equal mole ratio), rhombus (present study); NH4Cl + NH4I (equal mole ratio), nabla (present study): a NH4Cl, NH4Br, NH4Cl + NH4Br; b NH4Cl, NH4I, NH4Cl + NH4I
Discussion
According to our results, the slope of the GaN solubility curve can be changed by adding a mixed mineralizer, and can be controlled by the mixing ratio of the mineralizers.
In our previous studies [12, 18], the solubility of GaN in supercritical ammonia with acidic mineralizers (NH4Cl, NH4Br, and NH4I) was described by the van’t Hoff equation. Here we apply this equation to the solubility of GaN in supercritical ammonia with mixed mineralizers (NH4Cl + NH4Br, NH4Cl + NH4I).
In general, the van’t Hoff equation extracts the heat of solution from the temperature dependence of the solubility. The equation is given by
where s is the solubility in mol%, ∆H is the heat of solution in kJ/mol, R is the gas constant in J/(mol K), T is the temperature in K, and C is a constant. The compositions of the solvent and the dissolving species are assumed fixed under all experimental conditions.
Figure 3 plots the logarithmic solubility of GaN in the NH4Cl + NH4Br and NH4Cl + NH4I systems against the reciprocal of the absolute temperature.
The slope of the plot is almost constant in both systems, suggesting that the solubility species were unchanged over the investigated temperature range.
From the slopes of the straight lines in Fig. 3a and b, the heats of solution of GaN in supercritical ammonia were respectively calculated as follows.
-
∆H = 42.1 kJ/mol for NH4Cl + NH4Br
-
∆H = 39.0 kJ/mol for NH4Cl + NH4I.
Compared with data from Schimmel et al. [19], which were measured in situ, our solubility values [18] are high. Therefore, we examined the differences between our measurements and theirs. To improve X-ray transmission, Schimmel et al. used sapphire glass, which they state exhibits corrosion resistance under acidic ammonothermal conditions using NH4F or NH4Cl as a mineralizer. To investigate this, we performed a corrosion resistance test with sapphire glass under very similar conditions to those used by Schimmel et al. in their solubility experiments. These conditions were a temperature of 450 °C, pressure of 102 MPa, mineralizer concentration of 2.0 mol%, and reaction time of 6 h. We photographed the sapphire glass before and after the corrosion resistance test (Fig. 4). When NH4F was used as a mineralizer, the sapphire glass corroded and lost its transparency. By contrast, when NH4Cl was used as a mineralizer, the sapphire glass transparency was maintained. We also weighed the sapphire glass before and after the experiments (Table 3). With NH4F, the mass of the sapphire glass decreased, which indicated it corroded. With NH4Cl, although the transparency was maintained, the mass of the sapphire glass decreased slightly, which indicated that it also corroded a small amount. Sapphire glass clearly corroded in the 6-h NH4F reaction. Therefore, the solubility values from Schimmel et al. could be lower than the actual values because the mineralizer concentration decreased. However, when NH4Cl was used as a mineralizer, although the sapphire glass corroded slightly, it did not corrode enough to affect the solubility data. In this case, the differences between the two sets of solubility data cannot be explained by the use of sapphire glass.
Photographs showing the appearance of sapphire glass a before corrosion resistance test b after corrosion resistance test using NH4F mineralizer (b) after corrosion resistance test using NH4Cl mineralizer: corrosion resistance test conditions were 450 °C, 102 MPa, 2.0 ± 0.1 mol% mineralizer concentration
Pimputkar et al. [20] investigated the possibility of Ga sinking into Mo as a contributor to the decreased feed rate of raw material in experiments using Mo capsules. Therefore, we examined the possibility that our solubility data were high because of Ga sinking into Pt. First, we placed polycrystalline GaN in a Pt crucible and heated it in a nitrogen atmosphere at 400–600 °C for 100 h. We measured the masses of the Pt crucible and polycrystalline GaN before and after the experiment (Table 4). There were no changes in the masses of Pt crucible and polycrystalline GaN at any temperature, and no indication that Ga sinking into Pt occurred. Next, we placed a Pt plate on the bottom of the autoclave and polycrystalline GaN on the plate, and attempted to measure the solubility. The experimental conditions were a temperature of 420 °C, pressure of 101 MPa, mineralizer concentration of 3.0 mol%, and autoclave heating time of 100 h. The solubility (0.76 mol%) agreed with the previous measurement (0.79 mol%) [18] within the measurement uncertainty. We did not observe any mass change in the Pt plate after the experiment (Table 5), and it does not seem possible that our solubility data were high because Ga sank into Pt. When Pimputkar et al. considered the possibility of Ga sinking into Mo, they found that Mo and Ga did not form an alloy. As in the case of using Mo capsules, Ga did not sink into Pt and it did not affect the solubility data.
In their experimental procedure, Schimmel et al. released ammonia to adjust the pressure if necessary. However, because NH4Cl easily dissolves in ammonia, NH4Cl would also be released with the ammonia. Therefore, the mineralizer amount-of-substance fraction could not be accurate. They also did not weigh the ammonia, and there is uncertainty as to the amount of ammonia they used. In the experimental section, they describe that ammonia introduced into the autoclave up to fill factor of 60%. But, they do not mention the uncertainty around the amount of ammonia. In summary, it is not clear why our solubility data differ from those of Schimmel et al.
Conclusions
We investigated the change in solubility of gallium nitride (GaN) in supercritical ammonia in the presence of mixed mineralizers. The solubility curve of the NH4Cl + NH4Br system gradually became convex with increasing NH4Cl molar fraction. In contrast, the GaN solubility in the NH4Cl + NH4I system increased almost linearly with NH4Cl molar fraction. The temperature dependence of the solubility was investigated in 1:1 molar ratio mixtures. The slope of the dependence in the NH4Cl + NH4Br (NH4Cl + NH4I) system was intermediate between the slopes of the systems with single NH4Cl mineralizer and single NH4Br (NH4I) mineralizer. These results show that adding a mixed mineralizer to the system changes the slope of the solubility curve. Moreover, the GaN solubility can be controlled by the mixing ratio of the individual mineralizers.
References
Yamane H, Shimada Simon MJC, DiSalvo FJ (1997) Preparation of GaN single crystals using a Na flux. Chem Mater 9:413–416
Mori Y, Imade M, Murakami K, Takazawa H, Imabayashi H, Todoroki Y, Kitamoto K, Maruyama M, Yoshimura M, Kitaoka Y, Sasaki T (2012) Growth of bulk GaN crystal by Na flux method under various conditions. J Cryst Growth 350:72–74
Dwiliński R, Baranowski JM, Kamińska M, Doradziński R, Garczyński J, Sierzputowski L (1996) On GaN crystallization by ammonothermal method. Acta Phys Pol A 90:763–766
Dwiliński R, Doradziński R, Garczyński J, Sierzputowski L, Kucharski R, Zając M, Rudziński M, Kudrawiec M, Strupiński W, Misiewicz J (2011) Ammonothermal GaN substrates: growth accomplishments and applications. Phys Status Solidi A 208:1489–1493
Hashimotom T, Letts E, Ikari M, Nojima Y (2010) Improvement of crystal quality in ammonothermal growth of bulk GaN. J Cryst Growth 312:2503–2506
Wang B, Bliss D, Suscavage M, Swider S, Lancto R, Lynch C, Weyburn D, Li T, Ponce FA (2011) Ammonothermal growth of high-quality GaN crystals on HVPE template seeds. J Cryst Growth 318:1030–1033
Tomida D, Kagamitani Y, Bao Q, Hazu K, Sawayama H, Chichibu SF, Yokoyama C, Fukuda T, Ishiguro T (2012) Enhanced growth rate for ammonothermal gallium nitride crystal growth using ammonium iodide mineralizer. J Cryst Growth 353:59–62
Bao Q, Saito M, Hazu K, Furusawa K, Kagamitani Y, Kayano R, Tomida D, Qiao K, Ishiguro T, Yokoyama C, Chichibu SF (2013) Ammonothermal crystal growth of GaN using an NH4F mineralizer. Cryst Growth Des 13:4158–4161
Pimputkar S, Kawabata S, Speck JS, Nakamura S (2014) Improved growth rates and purity of basic ammonothermal GaN. J Cryst Growth 350:7–17
Jiang W, Ehrentraut D, Downey BC, Kamber DS, Pakalapati RT, Yoo HD, D’Evelyn MP (2014) Highly transparent ammonothermal bulk GaN substrates. J Cryst Growth 403:18–21
Yoshida K, Aoki K, Fukuda T (2014) High-temperature acidic ammonothermal method for GaN crystal growth. J Cryst Growth 393:93–97
Tomida D, Kuribayashi T, Suzuki K, Kagamitani Y, Ishiguro T, Fukuda T, Yokoyama C (2011) Effect of halogen species of acidic mineralizer on solubility of GaN in supercritical ammonia. J Cryst Growth 325:52–54
Kagamitani Y, Kuribayashi T, Hazu K, Onuma T, Tomida D, Shimura R, Chichibu SF, Sugiyama K, Ishiguro T, Fukuda T (2010) Ammonothermal epitaxy of wurtzite GaN using an NH4I mineralizer. J Cryst Growth 312:3384–3387
Wang B, Callahan MJ, Rakes KD, Bouthillette LO, Wang SQ, Bliss DF, Kolis JW (2006) Ammonothermal growth of GaN crystals in alkaline solutions. J Cryst Growth 287:376–380
Hashimoto T, Saito M, Fujito K, Wu F, Speck JS, Nakamura S (2007) Seeded growth of GaN by the basic ammonothermal method. J Cryst Growth 305:311–316
Dwiliński R, Doradziński R, Garczyński J, Sierzputowski LP, Puchalski A, Kanbara Y, Yagi K, Minakuchi H, Hayashi H (2008) Excellent crystallinity of truly bulk ammonothermal GaN. J Cryst Growth 310:3911–3916
Ehrentraut D, Kagamitani Y, Yokoyama C, Fukuda T (2008) Physico-chemical features of the acid ammonothermal growth of GaN. J Cryst Growth 310:891–895
Tomida D, Kuroda K, Hoshino N, Suzuki K, Kagamitani Y, Ishiguro T, Fukuda T, Yokoyama C (2010) Solubility of GaN in supercritical ammonia with ammonium chloride as a mineralizer. J Cryst Growth 312:3161–3164
Schimmel S, Lindner M, Steigerwald TG, Hertweck B, Richter TMM, Künecke U, Alt NSA, Niewa R, Schücker E, Wellmann PJ (2015) Determination of GaN solubility in supercritical ammonia with NH4F and NH4Cl mineralizer by in situ x-ray imaging of crystal dissolution. J Cryst Growth 418:64–69
Pimputkar S, Speck JS, Nakamura S (2016) Basic ammonothermal GaN growth in molybdenum capsules. J Cryst Growth 456:15–20
Authors’ contributions
DT designed the study, and wrote the initial draft of the manuscript. KK and KN carried out of the experimental work. KQ and CY contributed towards experiments and article preparation. All authors discussed the results and critically reviewed the manuscript. All authors read and approved the final manuscript.
Acknowledgements
This work was supported in part by the Project of Strategic Development for Energy Conservation Technology from a NEDO program by METI (Japan).
Competing interests
The authors declare that they have no competing interests.
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.
About this article
Cite this article
Tomida, D., Kuroda, K., Nakamura, K. et al. Temperature dependent control of the solubility of gallium nitride in supercritical ammonia using mixed mineralizer. Chemistry Central Journal 12, 127 (2018). https://doi.org/10.1186/s13065-018-0501-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13065-018-0501-7