1. Numerical simulation of pulverized wet coal combustion using detailed chemical kinetics

   • Valdeci José Costa
   • Viktor Georgevith Krioukov
   • Clóvis Raimundo Maliska

   Technical Paper 15 February 2014 Pages: 661 - 672

   

2. Analysis of syngas formation and ecological efficiency for the system of treating biomass waste and other solid fuels with CO₂ recuperation based on integrated gasification combined cycle with diesel engine

   • A. Y. Pilatau
   • H. A. Viarshyna
   • A. Matus

   Technical Paper 02 April 2014 Pages: 673 - 679

   

3. Mixed convective peristaltic transport in a vertical channel with Robin’s condition

   • Q. Hussain
   • T. Hayat
   • Hamed H. Alsulami

   Technical Paper 17 September 2013 Pages: 681 - 695

   

4. Determining of the hydrodynamic forces on the multi-hull tunnel vessel in steady motion

   • Morteza Ghassabzadeh
   • Hassan Ghassemi

   Technical Paper 26 October 2013 Pages: 697 - 708

   

5. Three-dimensional finite element method for rotating disk flows

   • G. R. Anjos
   • N. Mangiavacchi
   • J. Pontes

   Technical Paper 03 January 2014 Pages: 709 - 724

   

6. The feedback effect caused by bed load on a turbulent liquid flow

   • Erick de Moraes Franklin
   • Fabíola Tocchini de Figueiredo
   • Eugênio Spanó Rosa

   Technical Paper 03 January 2014 Pages: 725 - 736

   

7. A comparison of Fourier pseudospectral method and finite volume method used to solve the Burgers equation

   • A. A. Nascimento
   • F. P. Mariano
   • E. L. M. Padilla

   Technical Paper 27 February 2014 Pages: 737 - 742

   

8. Numerical and experimental study of a jet in a crossflow for different velocity ratio

   • Rim Ben Kalifa
   • Sabra Habli
   • Georges Le Palec

   Review Paper 24 January 2014 Pages: 743 - 762

   

9. Influence of the cutting edge micro-geometry of PCBN tools on the flank wear in orthogonal quenched and tempered turning M2 steel

   • Dilson José Aguiar de Souza
   • Walter Lindolfo Weingaertner
   • Cleiton Rodrigues Teixeira

   Technical Paper 15 November 2013 Pages: 763 - 774

   

10. Correlating tool wear, surface roughness and corrosion resistance in the turning process of super duplex stainless steel

    • Carlos Ancelmo de Oliveira Junior
    • Anselmo Eduardo Diniz
    • Rodnei Bertazzoli

    Technical Paper 12 December 2013 Pages: 775 - 785

    

11. Influence of the manufacturing process in performance concerning wear of total hip prostheses

    • A. L. L. Oliveira

    Review Paper 29 December 2013 Pages: 787 - 795

    

12. Experimental investigation of hole quality during reaming applications using multi-blade tools

    • K. Schützer
    • M. Roth
    • T. Hauer

    Technical Paper 21 January 2014 Pages: 797 - 806

    

13. Investigations into the surface quality and micro-hardness in the ultrasonic machining of titanium (ASTM GRADE-1)

    • Jatinder Kumar

    Technical Paper 23 January 2014 Pages: 807 - 823

    

14. Numerical investigation of the heat transfer enhancement using various viscosity models in chamber filled with water–CuO nanofluid

    • Ashkan Ghafouri
    • Mehdi Salari

    Technical Paper 11 September 2013 Pages: 825 - 836

    

15. Numerical simulation of filling process of natural gas onboard vehicle cylinder

    • Navid NoorAliPour Nahavandi
    • Mahmood Farzaneh-Gord

    Technical Paper 02 October 2013 Pages: 837 - 846

    

16. Modeling heat transfer with micro-scale natural convection in fibrous insulation

    • Humberto Araujo Machado

    Technical Paper 29 September 2013 Pages: 847 - 857

    

17. An integration of TRIZ and the systematic approach of Pahl and Beitz for innovative conceptual design process

    • Murat Mayda
    • Hüseyin R. Börklü

    Technical Paper 01 October 2013 Pages: 859 - 870

    

18. DTW: a design method for designing robot end-effectors

    • Luís Fernando Ferreira Furtado
    • Emilia Villani
    • Carlos Eduardo Oliveira Silva

    Technical Paper 15 October 2013 Pages: 871 - 885

    

19. Orthotropic material models for the nonlinear analysis of structural membranes

    • Fernando R. Gonçalves
    • Eduardo M. B. Campello

    Technical Paper 24 November 2013 Pages: 887 - 899

    

20. A method for reduction of uncertainties in reservoir model using observed data: application to a complex case

    • Célio Maschio
    • Denis Jose Schiozer

    Technical Paper 06 February 2014 Pages: 901 - 918

    

21. Automatic history matching considering surrogate-based optimization and Karhunen–Loève expansions

    • José Dásio de Lira Jr.
    • Ramiro B. Willmersdorf
    • Bernardo Horowitz

    Technical Paper 19 January 2014 Pages: 919 - 928

    

22. Torque for an electromechanical integrated harmonic piezodrive system

    • Lizhong Xu
    • Cong Li
    • Huaiyong Li

    Technical Paper 07 November 2013 Pages: 929 - 937

    

23. Effect of interfacial powder on mechanical properties of composites under dynamic tests

    • Y. Mebarki
    • S. Rechak
    • A. Maslouhi

    Technical Paper 23 January 2014 Pages: 939 - 949

    

24. Non-Newtonian nanofluid free convection flow subject to mixed thermal boundary conditions about a vertical cone

    • A. Mahdy

    Technical Paper 13 February 2014 Pages: 951 - 960