1. Axisymmetric control valve for oil and gas equipment

   • I. N. Karelin

   OriginalPaper 12 March 2017 Pages: 87 - 90

2. Energy-saving modular electric furnaces with energy recuperation

   • A. I. Nizhegorodov

   OriginalPaper 12 March 2017 Pages: 91 - 96

3. Determining the elastic modulus of a hard coating from the loading curve in indentation

   • N. A. Voronin

   OriginalPaper 12 March 2017 Pages: 97 - 102

4. Damping characteristics of cable-based dampers and hydraulic bearings

   • B. A. Gordeev
   • S. N. Okhulkov
   • P. A. Zlobin

   OriginalPaper 12 March 2017 Pages: 103 - 109

5. Drawing of two-layer axisymmetric anisotropic components with wall thinning

   • S. S. Yakovlev
   • M. V. Gryazev
   • O. V. Pilipenko

   OriginalPaper 12 March 2017 Pages: 110 - 116

6. Edge forces in machining by abrasive brushes

   • Yu. V. Dimov
   • D. B. Podashev

   OriginalPaper 12 March 2017 Pages: 117 - 121

7. Programmable end milling of thermoplastics

   • A. A. Emel’yanenko
   • O. I. Zhabin
   • Yu. N. Polyanchikov

   OriginalPaper 12 March 2017 Pages: 122 - 124

8. Cutting characteristics in the end milling of stainless steel

   • S. V. Grubyi

   OriginalPaper 12 March 2017 Pages: 125 - 133

9. Verifying the geometric precision of machine tools

   • R. R. Kadyrov
   • R. G. Kudoyarov

   OriginalPaper 12 March 2017 Pages: 134 - 139

10. Modernization of numerically controlled machine tools on modular principles

    • V. V. Platonov
    • E. V. Platonova
    • I. G. Maizel

    OriginalPaper 12 March 2017 Pages: 140 - 143

11. Wear resistance of hard-alloy disk mills with different flank geometry

    • N. Yu. Kovelenov
    • S. V. Bolotskikh
    • A. S. Mikhailov

    OriginalPaper 12 March 2017 Pages: 144 - 147

12. Hard-alloy metal-cutting tool for the finishing of hard materials

    • D. S. Rechenko
    • A. Yu. Popov
    • A. A. Kuznetsov

    OriginalPaper 12 March 2017 Pages: 148 - 149

13. Simulation of grinding with wear of the abrasive grains

    • D. V. Ardashev
    • L. V. Shipulin

    OriginalPaper 12 March 2017 Pages: 150 - 153

14. Influence of the boundary conditions on the forces in the abrasive machining of rubber

    • A. M. Khanov
    • L. D. Sirotenko
    • A. A. Drozdov

    OriginalPaper 12 March 2017 Pages: 154 - 157

15. Attractive manifolds in end milling

    • V. L. Zakovorotny
    • A. A. Gubanova
    • A. D. Lukyanov

    OriginalPaper 12 March 2017 Pages: 158 - 163

16. Continuum design of grinding operations

    • D. V. Ardashev
    • V. I. Guzeev

    OriginalPaper 12 March 2017 Pages: 164 - 166

17. Factors affecting the angular velocity of the workpiece in abrasive finishing

    • K. R. Muratov
    • E. A. Gashev
    • D. M. Lagunov

    OriginalPaper 12 March 2017 Pages: 167 - 170