1. Reduction and decarburization annealing of atomized powders in converted gas

   • E. Ya. Popichenko
   • I. D. Radomy sel'skii

   OriginalPaper Pages: 825 - 828

2. Effect of particle size of metal powders on their degree of ultrasonic purification in a pickling solution

   • I. I. Odokienko
   • S. M. Solonin
   • O. S. Nichiporenko

   OriginalPaper Pages: 829 - 832

3. Effect of additions of Na, Mg, and Al cations on the flowability, apparent density, and composition of copper powder

   • A. V. Pomosov
   • L. P. Mozhar

   OriginalPaper Pages: 832 - 834

4. Preparation and properties of Al₂O₃-Al and ZrO₂-Al powders

   • N. N. Novikov
   • S. R. Pustotina
   • N. M. Piskareva

   OriginalPaper Pages: 834 - 837

5. Structure formation in a Ti-chromium-carbide composite during sintering

   • R. Z. Vlasyuk
   • I. D. Radomysei'skii

   OriginalPaper Pages: 838 - 840

6. A method of producing bulk-boronized materials

   • V. V. Chernienko
   • A. K. Mashkov

   OriginalPaper Pages: 841 - 843

7. Structural characteristics of permeable materials from metal fibers

   • A. G. Kostornov
   • A. L. Moroz
   • A. V. Perepelkin

   OriginalPaper Pages: 844 - 849

8. Adhesional reactions of titanium with refractory metals

   • A. L. Borisova
   • Yu. N. Kopichev

   OriginalPaper Pages: 849 - 852

9. An ultrasonic method of mixing powders of refractory metal dichalcogenides with gallium-base low-melting-point alloys

   • T. A. Lobova
   • G. A. Shvetsova
   • E. P. Terenin

   OriginalPaper Pages: 852 - 854

10. Constitution diagrams of metal-hydrogen systems and characteristics of hydride structure formation

    • R. A. Andrievskii
    • E. B. Boiko
    • A. M. Solodinin

    OriginalPaper Pages: 855 - 860

11. The wetting of self-bonded polycrystalline silicon carbide by silicon

    • V. L. Yupko
    • G. G. Gnesin
    • Z. V. Sichkar'

    OriginalPaper Pages: 860 - 862

12. Effect of bismuth oxide on the phase composition and magnetic properties of the 12Fe₂O₃ · 3BaO · 2CoO system

    • E. A. Kuchinskaya
    • A. G. Titenko
    • S. E. Shaporenko

    OriginalPaper Pages: 863 - 866

13. Bulk electrical resistivity of technical silicon carbide in a SiC-Si composite

    • G. G. Gnesin
    • L. A. Shipilova
    • I. E. Polomoshnov

    OriginalPaper Pages: 866 - 871

14. Effect of milling conditions on the fine crystal structure and activity of 6SChl ferrite

    • I. I. Zver'kova
    • E. V. Elfimova
    • V. I. Fadeeva

    OriginalPaper Pages: 872 - 874

15. Adhesion of a powder layer applied by the hot pressing method to a dense steel basis

    • R. G. Berezin
    • V. A. Martynov
    • N. V. Avdeev

    OriginalPaper Pages: 875 - 878

16. Effect of the re-pressing of preforms under high hydrostatic pressure on the fine structure of the carbide phases of compacts and sintered VK10 alloy

    • Yu. F. Chernyi
    • G. P. Mikhailenko
    • L. I. Lavrukhina

    OriginalPaper Pages: 879 - 882

17. Antifriction peoperties of sintered iron-base materials containing sulfur and phosphorus

    • N. V. Manukyan
    • G. B. Bagdasaryan
    • S. A. Malkhasyan

    OriginalPaper Pages: 883 - 887

18. A method of increasing the mechanical strength of ferrite cores

    • M. A. Zinovik

    OriginalPaper Pages: 888 - 890

19. Reduction and decarburization during the annealing of atomized cast iron powder with converted gas in brovary powder metallurgy factory industrial furnaces

    • É. Ya. Popichenko
    • A. F. Zhornyak
    • N. D. Pavlina

    OriginalPaper Pages: 891 - 893

20. Production of parts by the powder metallurgy method for the Kama Automobile Factory

    • V. V. Saklinskii
    • E. V. Kruglov

    OriginalPaper Pages: 893 - 896

21. Pore-size distribution in and permeability of oxide coatings

    • S. S. Bartenev

    OriginalPaper Pages: 897 - 900

22. Ignition prevention during the comminution of reduced sponge iron

    • O. D. Neikov

    OriginalPaper Pages: 901 - 904