1. Processes and equipment for chemical and oil-gas production

   • V. I. Kochetov
   • S. I. Lazarev
   • D. V. Tulyakov

   Research, Design, Calculations, and Operating Experience 11 November 2010 Pages: 363 - 373

   

2. Hydraulic resistance of an absorber with a fibrous packing

   • E. V. Polienova
   • A. Yu. Valdberg

   OriginalPaper 11 November 2010 Pages: 374 - 378

   

3. Fluid dispersers with adaptive vibrators

   • V. I. Kolchkov
   • M. K. Rustambekov

   OriginalPaper 11 November 2010 Pages: 379 - 382

   

4. Extending service life of parts molding plastic articles

   • V. M. Yanko

   OriginalPaper 10 November 2010 Pages: 383 - 386

   

5. Heat exchange in the rolls of vulcanizing equipment for gumming

   • S. Yu. Osipov
   • V. A. Bystroumov
   • Yu. R. Osipov

   OriginalPaper 11 November 2010 Pages: 387 - 391

   

6. Petrochemical reactor designing based on mathematical modeling with reference to ethylene polymerization reactor

   • I. A. Yankina
   • M. G. Berengarten
   • A. E. Sofiev

   OriginalPaper 11 November 2010 Pages: 392 - 396

   

7. Analysis of existing small-capacity plants for natural-gas liquefaction

   • A. M. Arkharov
   • I. A. Arkharov
   • A. N. Kolobova

   Cryogenic Engineering, Production and use of Industrial Gases, Vacuum Engineering 12 November 2010 Pages: 397 - 416

   

8. Prospects for application of two-screw pump-compressors

   • A. F. Sadykov
   • R. M. Nazmutdinov

   Compressors, Pumps, and Pipeline Fittings 10 November 2010 Pages: 417 - 420

   

9. New-generation crude-oil pumps in refinery coking units

   • A. I. Shvindin
   • O. S. Lvov

   OriginalPaper 10 November 2010 Pages: 421 - 424

   

10. Approach to selection of a reactor-cooler in cleaning systems for gases formed during detoxification of poisonous substances

    • A. Yu. Valdberg
    • N. E. Vaulin
    • V. I. Lazarev

    Industrial Ecology 11 November 2010 Pages: 425 - 430

    

11. Processes and Equipment for Chemical and Oil-Gas Production

    • A. E. Ivanov
    • M. G. Berengarten
    • M. I. Klyushenkova

    Research, Design, Calculations, and Operating Experience 10 November 2010 Pages: 433 - 440

    

12. Thermal status of the noise- and heat-protective housing of a gas-turbine plant in a gas-pumping unit

    • P. V. Trusov
    • D. A. Charntsev
    • A. M. Pechenkina

    OriginalPaper 10 November 2010 Pages: 441 - 445

    

13. Variation of liquid level in stages of mass-transfer unit with direct-flow/vortical contact devices

    • A. V. Dmitriev
    • I. R. Kalimullin
    • A. N. Nikolaev

    OriginalPaper 10 November 2010 Pages: 446 - 450

    

14. History of development and current state of hydrodynamic rotary mixers

    • E. A. Nikolaev
    • S. P. Ivanov
    • N. S. Shulaev

    OriginalPaper 10 November 2010 Pages: 451 - 455

    

15. Producing water with near-zero temperature in vacuum process

    • B. T. Marinyuk
    • A. A. Hegazy

    OriginalPaper 10 November 2010 Pages: 456 - 457

    

16. Model of viscoplasticity with parallel deformation mechanisms. Part 1. Constitutive equations and choice of calculation coefficients^*

    • G. M. Khazhinskii

    OriginalPaper 10 November 2010 Pages: 458 - 467

    

17. Experimental determination of tetrafluoromethane and hexafluoroethane accumulation in khrom-3 krypton–xenon mixture producing equipment

    • V. L. Bondarenko
    • N. P. Losyakov
    • A. A. Vinnik

    Cryogenic Engineering, Production and Use Of Industrial Gases, Vacuum Engineering 10 November 2010 Pages: 468 - 473

    

18. Influence of fat content and temperature of liquid on krypton solubility. Experimental data

    • A. V. Potapov
    • I. A. Arkharov

    OriginalPaper 10 November 2010 Pages: 474 - 478

    

19. Influence of type of high-coercivity permanent magnet on characteristics of magnetic clutch

    • A. Ya. Krasilnikov
    • A. A. Krasilnikov

    Complementary Products and Devices 10 November 2010 Pages: 479 - 484

    

20. Study of the effect of thinning during forming on the strength of elliptical dishes of titanium VT1-0

    • S. M. Kutepov
    • E. A. Sadovskaya
    • Yu. A. Kurilina

    Manufacturing Technology 10 November 2010 Pages: 485 - 490