Abstract
This study examines the design and numerical analysis of induction hardened of Inconel 718 superalloys on the tensile properties. The two tensile specimens (IHT1 & IHT2)’s outside surfaces are heated to temperatures of 850 and 1000 °C. The heated samples are then quenched in oil. The samples are evaluated utilizing a 250kN capacity servo hydraulic universal test at ambient temperature and an enhanced temperature of 800 °C. At both room temperature and a raised temperature of 800 °C, the metrics yield strength (YS), ultimate tensile strength (UTS), and elongation of induction hardened sample have risen. Induction-hardened materials have better mechanical characteristics than non-induction-hardened samples, according to numerical results from ANSYS Workbench that are corroborated with experimental data. The results of the tensile test’s cracked surfaces under a scanning electron microscope (SEM) show that the presence of shallow dimple structure at 800 °C caused transgranular cleavage and intergranular dimple rupture as the modes of failure.
Similar content being viewed by others
References
Hitesh Vasudev, L., Thakur, A., Bansal, H., Singh, Zafar, S.: “High temperature oxidation and erosion behaviour of HVOF sprayed bi-layer Alloy-718/NiCrAlY coating”, Surface and Coatings Technology,362 pp.366–380. (2019)
Prashar, G., Vasudev, H.: Surface topology analysis of plasma sprayed Inconel625-Al2O3 composite coating,” Materials Today: Proceedings, no. xxxx, 2021(Elsevier, Scopus Indexed). Volume 50, Part 5, Pages 607–611 (2022). https://doi.org/10.1016/j.matpr.2021.03.090
Hitesh Vasudev, P., Singh, L., Thakur, Bansal, A.: “Mechanical and microstructural characterization of microwave post processed Alloy-718 coating,” Materials Research Express, vol. 6, no. 12, p. 1265f5, Jan. (2020)
Hitesh Vasudev, L., Thakur, A., Bansal, H., Singh: An investigation on oxidation behaviour of high velocity oxy-fuel sprayed IN718- Al2O3composite coatings. Surf. Coat. Technol. (2020). https://doi.org/10.1016/j.surfcoat.2020.125770
Vasudev, H., Thakur, L., Singh, H., Bansal, A.: A study on processing and hot corrosion behaviour of HVOF sprayed Inconel718-nano Al2O3 coatings. Mater. Today Commun. 25, 101626 (2020). https://doi.org/10.1016/j.mtcomm.2020.101626
Vasudev, H., Prashar, G., Thakur, L.: and A. Bansal, ”Microstructural characterization and electrochemical corrosion behaviour of HVOF sprayed Alloy718-nanoAl2O3 composite coatings”, Surface Topography: Metrology and Properties 9 10.1088/2051-672X/ac1044 (2021)
Vasudev, H., Thakur, L., Bansal, A., Singh, H.: Erosion behaviour of HVOF sprayed Alloy718-nano Al2O3 composite coatings on grey cast iron at elevated temperature conditions. Surf. Topogr. Metrol. Prop. (2021). https://doi.org/10.1088/2051-672X/ac1c80
Vasudev, H., Prashar, G., Thakur, L., Bansal, A.: “Electrochemical Corrosion Behaviour and Microstructural Characterization of HVOF Sprayed Inconel718-Al2O3 Composite Coatings” Surface review and letters; (2021). https://doi.org/10.1142/S0218625X22500172
WANG, Y., SHAO, W.Z., YANG, Z.H.E.N.L., ZHANG, C. XM: Tensile deformation behavior of superalloy 718 at elevated temperatures. J. Alloys Compd. 471, 331–335 (2009). https://doi.org/10.1016/j.jallcom.2008.03.082
LIU, B.B., HAN, J.Q., ZHAO, R., LIU, W., WAN, M.: Grain size effect on fracture behavior of the axis-tensile test of Inconel 718 sheet. High. Temp. Mater. Proc. 35, 989–998 (2016). https://doi.org/10.1515/htmp-2015-0102
ZHAO, R., LI, X.J., WAN, M., HAN, J.Q., MENG, B., CAI, Z.Y.: Fracture behavior of Inconel 718 sheet in thermal-aideddeformation considering grain size effect and strain rate influence. Mater. Des. 130, 413–425 (2017). https://doi.org/10.1016/j.matdes.2017.05.089
LIN, Y.C., DENG, J., JIANG, Y.Q., WEN, D.X., LIU, G.: Hot tensile deformation behaviors and fracture characteristics of a typical Ni-based superalloy. Mater. Des. 55, 949–957 (2014). https://doi.org/10.1016/j.matdes.2013.10.071
Sharma, Y., K.Singh and, Vasudev, H.: Experimental studies on friction stir welding of aluminium alloys,” Materials Today: Proceedings, Volume 50, Part 5, Pages 2387–2391 (2022). https://doi.org/10.1016/j.matpr.2021.10.254
Singh, G., Vasudev, H., Bansal, A.: Influence of heat treatment on the microstructure and corrosion properties of the Inconel-625 clad deposited by microwave heating. Surf. Topogr. Metrol. Prop. 9, 025019 (2021). https://doi.org/10.1088/2051-672X/abfc61
Amit Bansal, H., Vasudev, P., kumar, A.K., Sharma: Investigation on the effect of post weld heat treatment on microwave joining of the Alloy-718 weldment. Mater. Res. Express. 8, 1–12 (2019)
DU, B., YANG, J., CUI, C., SUN, X.: Effects of grain refinement on the microstructure and tensile behavior of K417G superalloy. Mater. Sci. Eng. A. 623, 59–67 (2015). https://doi.org/10.1016/j.msea.2014.11.041
LIN, Y.C., LI, L., HE, D.G., CHEN, M.S., LIU, G.Q.: Effects of pre-treatments on mechanical properties and fracture mechanism of a nickel-based superalloy. Mater. Sci. Eng. A. 679, 401–409 (2017). https://doi.org/10.1016/j.msea.2016.10.058
LIN, Y.C., DENG, J., JIANG, Y.Q., WEN, D.X., LIU, G.: Hot tensile deformation behaviors and fracture characteristics of a typical Ni-based superalloy. Mater Des 55:949–957. https://doi/org/j.matdes.2013.10.071. (2014)
ZHAO, R., LI, X.J., WAN, M., HAN, J.Q., MENG, B., CAI, Z.Y.: Fracture behavior of Inconel 718 sheet in thermal-aided deformation considering grain size effect and strain rate influence. Mater. Des. 130, 413–425 (2017). https://doi.org/10.1016/j.matdes.2017.05.089
LIU, Z.G., LI, P.J., XIONG, L.T., LIU, T.Y., HE, L.J.: High temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy. Mater. Sci. EngA. 680, 259–269 (2017). https://doi.org/10.1016/j.msea.2016.10.095
LI, X.F., ZHANG, J., FU, Q.Q., SONG, A.K.I.Y.A.M.A.E., WANG, X.L., LI, Y.F., ZOU, Q.Z. N: Tensile mechanical properties and fracture behaviors of nickel-based superalloy 718 in the presence of hydrogen. Int. J. Hydrog Energy. 43, 20118–20132 (2018). https://doi.org/10.1016/j.ihydene.2018.08.179
ALABORT, E., BARBA, D., SULZER, S., LIBNER, M., PETRINIC, N., REED, R.C.: Grain boundary properties of a nickel-based superalloy: Characterisation and modeling. Acta Mater. 151, 377–394 (2018). https://doi.org/10.1016/jactamat.2018.03.059
ZHANG, Z.Y.U.J., YUAN, Y., ZHOU, R., ZHANG, H., WANG, H.: Microstructural evolution and mechanical properties of Inconel 718 after thermal exposure. Mater. Sci. Eng. A. 634, 55–63 (2015). https://doi.org/10.1016/j.msea.2015.03.004
ZHANG, L., LI, D., QU, X.H., QIN, M.L., HE, X.B., LI, Z.: Microstructure and tensile properties optimization of MIM418 superalloy by heat treatment. J. Mater. Process. Technol. 227, 71–79 (2016). https://doi.org/10.1016/j.jmatprotec.2015.08.001
OZGUN, O., YILMAZ, R., GULSOY, H.O., FINDIK, F.: The effect of aging treatment on the fracture toughness and impact strength of injection molded Ni-625 superalloy parts. Mater. Charact. 108, 8–15 (2015). https://doi.org/10.1016/j.matchar.2015.08
Sudheer, D., Kulkarni, M., Chandrasekhar, U., Manjunath, K.V., Durga Prasad, C., Vasudev, H.: “Design and Optimization of Polyvinyl-Nitride Rubber for Tensile Strength Analysis”, International Journal on Interactive Design and Manufacturing (IJIDeM), Springer, (2023). https://doi.org/10.1007/s12008-023-01405-6
Mahantesh, M., Math, Rajeswara Rao, K.V.S., Prapul Chandra, A.C., Vijayakumar, M.N., Nandini, B., Prasad, C.D., Vasudev, H.: “Design and Modeling using Finite Element Analysis for the Sitting Posture of Computer Users Based on Ergonomic Perspective”, International Journal on Interactive Design and Manufacturing (IJIDeM), Springer, (2023). https://doi.org/10.1007/s12008-023-01383-9
Madhu Sudana Reddy, G., Durga Prasad, C., Kollur, S., Lakshmikanthan, A., Suresh, R.: Aprameya C R, “Investigation of High Temperature Erosion Behaviour of NiCrAlY/TiO2 Plasma Coatings on Titanium Substrate”, JOM The Journal of The Minerals, Metals & Materials Society (TMS), Springer, https://doi.org/10.1007/s11837-023-05894-4
Pulla Nagabhushana, S., Ramprasad, C.D., Prasad, H., Vasudev, C., Prakash: “Numerical Investigation on Heat Transfer of a Nano-Fluid Saturated Vertical Composite Porous Channel Packed between Two Fluid Layers”, International Journal on Interactive Design and Manufacturing (IJIDeM), Springer, (2023). https://doi.org/10.1007/s12008-023-01379-5
Praveen, N., Mallik, U.S., Shivasiddaramaih, A.G., Suresh, R., Durga Prasad, C., Shivaramu, L.: “Synthesis and Wire EDM Characteristics of Cu–Al–Mn Ternary Shape Memory Alloys Using Taguchi Method”, Journal of The Institution of Engineers (India): Series D, Springer, (2023). https://doi.org/10.1007/s40033-023-00501-x
Anjaneya, G., Sunil, S., Kakkeri, S., Mahantesh, M., Math, M.N., Vaibhav, C., Solaimuthu, C.D., Prasad, H., Vasudev: “Numerical Simulation of Microchannel Heat Exchanger using CFD”, International Journal on Interactive Design and Manufacturing (IJIDeM), Springer, (2023). https://doi.org/10.1007/s12008-023-01376-8
Mohan Poojari, H., Hanumanthappa, C.D., Prasad, H.M., Jathanna, A.R., Ksheerasagar, P., Shetty, B.K., Shanmugam, H., Vasudev: “Computational Modelling for the Manufacturing of Solar-Powered Multifunctional Agricultural Robot”, International Journal on Interactive Design and Manufacturing (IJIDeM), Springer, (2023). https://doi.org/10.1007/s12008-023-01291-y
Manjunatha, C.J., Durga Prasad, C., Harish Hanumanthappa, R., Kannan, A., Dhanesh, G., Mohan, B.K., Shanmugam, Venkategowda, C.: “Influence of Microstructural Characteristics on Wear and Corrosion Behaviour of Si3N4 Reinforced Al2219 Composites”, Advances in Materials Science and Engineering, Hindawi, vol. Article ID 1120569, (2023), (2023). https://doi.org/10.1155/2023/1120569
Sharanabasva, H., Durga Prasad, C.: Characterization and wear behavior of NiCrMoSi Microwave Cladding. J. Mater. Eng. Perform. (2023). https://doi.org/10.1007/s11665-023-07998-z
Sharanabasva, H., Durga Prasad, C.: Effect of Mo and SiC reinforced NiCr Microwave Cladding on microstructure, mechanical and wear Properties. J. Institution Eng. (India): Ser. D. (2023). https://doi.org/10.1007/s40033-022-00445-8
Nithin, H.S., Nishchitha, K.M., Pradeep, D.G., Durga Prasad, C., Mathapati, M.: Comparative analysis of CoCrAlY Coatings at High Temperature Oxidation Behavior using different reinforcement composition profiles. Weld. World. 67, 585–592 (2023). https://doi.org/10.1007/s40194-022-01405-2
Naveen, D.C., Naresh Kakur, Keerthi Gowda, B.S., Madhu Sudana Reddy, G., Durga Prasad, C., Ragavanantham Shanmugam: “Effects of Polypropylene Waste Addition as Coarse Aggregate in Concrete: Experimental Characterization and Statistical Analysis”, Advances in Materials Science and Engineering, Hindawi, vol. Article ID 7886722, 11 pages, (2022), (2022). https://doi.org/10.1155/2022/7886722
Venkate Gowda, H., Hanumanthappa, B.K., Shanmugam, C., Durga Prasad, T.N., Sreenivasa, M.S., Rajendra Kumar: High-temperature Tribological Studies on Hot Forged Al6061- Tib2 In-Situ Composites. J. Bio Tribo-Corrosion. 8, 101 (2022). https://doi.org/10.1007/s40735-022-00699-5
Madhusudana Reddy, G., Durga Prasad, C., Patil, P., Kakur, N., Ramesh, M.R.: Elevated temperature Erosion performance of plasma sprayed NiCrAlY/TiO2 coating on MDN 420 Steel substrate. Surf. Topogr. Metrol. Prop. 10, 025010 (2022). https://doi.org/10.1088/2051-672X/ac6a6e
Madhusudana Reddy, G., Durga Prasad, C., Shetty, G., Nageswara Rao, R.M.R. T, and, Patil, P.: “Investigation of thermally sprayed NiCrAlY/TiO2 and NiCrAlY/Cr2O3/YSZ Cermet Composite Coatings on Titanium Alloys”. Eng. Res. Express, Vol 4, 025049, https://doi.org/10.1088/2631-8695/ac7946
Madhusudana Reddy, G., Durga Prasad, C., Shetty, G., Nageswara Rao, R.M.R. T and, Patil, P.: “High Temperature Oxidation Behavior of Plasma Sprayed NiCrAlY/TiO2 & NiCrAlY /Cr2O3/YSZ Coatings on Titanium Alloy”. Welding in the World, Springer (2022). https://doi.org/10.1007/s40194-022-01268-7
Thavaraya Naik, M., Mathapathi, C., Durga Prasad, Nithin, H.S., Ramesh, M.R.: Effect of laser Post Treatment on Microstructural and sliding wear behavior of HVOF sprayed NiCrC and NiCrSi Coatings. Surf. Rev. Lett. 29(1), 225000 (2022). https://doi.org/10.1142/S0218625X2250007X
Madhusudana Reddy, G., Durga Prasad, C., Shetty, G., Nageswara Rao, R.M.R. T and, Patil, P.: High temperature oxidation studies of plasma sprayed NiCrAlY/TiO2 & NiCrAlY /Cr2O3/YSZ Cermet Composite Coatings on MDN-420 Special Steel Alloy. Metallography Microstruct. Anal. 10, 642–651 (2021). https://doi.org/10.1007/s13632-021-00784-0
Mahantayya Mathapati, K., Amate, C., Durga Prasad, Jayavardhana, M.L., Hemanth Raju, T.: “A Review on Fly ash Utilization”. Materials Today Proceedings, Elsevier Science, Vol. 50, Part 5, pp 1535–1540. (2022). https://doi.org/10.1016/j.matpr.2021.09.106
Rayirth Dinesh, Rohan Raykar, S., Rakesh, T.L., Prajwal, M.G., Shashank Lingappa, M., Durga Prasad, C.: “Feasibility study on MoCoCrSi/ WC-Co cladding developed on austenitic stainless steel using microwave hybrid heating”. J. Mines Met. Fuels, Volume 69, Issue 12A, December 2021, https://doi.org/10.18311/jmmf/2021/30113
Prasad, C.D., Lingappa, S., Joladarashi, S., Ramesh, M.R., Sachin, B.: “Characterization and Sliding Wear Behavior of CoMoCrSi + Flyash Composite Cladding Processed by Microwave irradiation”, Materials Today Proceedings, Elsevier Science, vol 46, pp 2387–2391, (2021). https://doi.org/10.1016/j.matpr.2021.01.156
Madhu, G., Mrityunjaya Swamy, K.M., Kumar, D.A., Durga Prasad, C., Harish, U.: Evaluation of hot corrosion behavior of HVOF thermally sprayed Cr3C2 -35NiCr coating on SS 304 boiler tube steel. Am. Inst. Phys. 2316, 030014 (2021). https://doi.org/10.1063/5.0038279
Prasad, C.D., Mathapathi, M., Vasudev, H., Thakur, L.: “Analysis of Mechanical Properties and Microstructural Characterisation of Microwave Cladding on Stainless Steel”, in a book titled “Advances in Microwave Processing for Engineering Materials”, CRC Press, Taylor & Francis Group, ISBN: 9781003248743, (2022). https://doi.org/10.1201/9781003248743
Prasad, C.D., Mathapathi, M., Joladarashi, S., Ramesh, M.R., Francis Group: “Investigation of Microstructural and Tribological Behavior of Metco 41 C + WC-12Co Composite Coating Sprayed by HVOF Process”, in a book titled “Thermal Spray Coatings”. CRC Press, Taylor and. ISBN: 9781032081489. (2021). https://doi.org/10.1201/9781003213185
Prasad, C.D., Jerri, A., Ramesh, M.R., Francis Group: “Evaluation of Microstructural and Dry Sliding Wear Resistance of Iron-Based SiC-Reinforced Composite Coating by HVOF Process”, in a book titled “Thermal Spray Coatings”. CRC Press, Taylor and. ISBN: 9781032081489. (2021). https://doi.org/10.1201/9781003213185
Sachin, B., Charitha, M., Rao, G.M., Naik, D., Prasad, C., Ajit, M., Hebbale, Vijeesh, V., Muralidhara Rao: “Minimum quantity lubrication and cryogenic for burnishing of difficult to cut material as a sustainable alternative”, Lecture Notes in Mechanical Engineering. Springer, ISBN - 978-981-16-2278-6, (2021). https://doi.org/10.1007/978-981-16-2278-6_6
Reddy, M.S., Durga Prasad, C., Patil, P., Ramesh, M.R., Rao, N.: Hot corrosion behavior of plasma sprayed NiCrAlY/TiO2 and NiCrAlY/Cr2O3/YSZ cermets coatings on alloy steel. Surf. Interfaces Elsevier Sci. 22, 100810 (2021). https://doi.org/10.1016/j.surfin.2020.100810
Prasad, C.D., Joladarashi, S., Ramesh, M.R., Srinath, M.S.: Microstructure and Tribological Resistance of Flame sprayed CoMoCrSi/WC-CrC-Ni and CoMoCrSi/WC-12Co composite Coatings Remelted by Microwave Hybrid Heating. J. Bio Tribo-Corrosion Springer. 6, 124 (2020). https://doi.org/10.1007/s40735-020-00421-3
Durga Prasad, C., Joladarashi, S., Ramesh, M.R.: Comparative investigation of HVOF and Flame Sprayed CoMoCrSi Coating. Am. Inst. Phys. 2247, 050004 (2020). https://doi.org/10.1063/5.0003883
Prasad, C.D., Jerri, A., Ramesh, M.R.: Characterization and sliding wear behavior of Iron Based Metallic Coating deposited by HVOF process on low Carbon Steel substrate. J. Bio Tribo-Corrosion Springer. 6, 69 (2020). https://doi.org/10.1007/s40735-020-00366-7
Prasad, C.D., Joladarashi, S., Ramesh, M.R., Srinath, M.S., Channabasappa, B.H.: “Comparison of High Temperature Wear Behavior of Microwave Assisted HVOF Sprayed CoMoCrSi-WC-CrC-Ni/WC-12Co Composite Coatings”. Silicon, Springer, 12, pp 3027–3045 1–19 (2020). https://doi.org/10.1007/s12633-020-00398-1
Giridhar, S., Kulkarni, N.G., Siddeshkumar, C., Durga Prasad, L., Shankar, Suresh, R.: “Drilling of GFRP with Liquid Silicon Rubber Reinforced with fine Aluminium Powder on Hole Surface Quality and Tool Wear using DOE”, Journal of Bio- and Tribo-Corrosion, Springer, volume 9, Article number: 53 (2023). https://doi.org/10.1007/s40735-023-00771-8
Durga Prasad, C., Joladarashi, S., Ramesh, M.R., Srinath, M.S., Channabasappa, B.H.: Effect of microwave heating on microstructure and elevated temperature Adhesive wear behavior of HVOF deposited CoMoCrSi-Cr3C2 Composite Coating. Surf. Coat. Technol. Elsevier Sci. 374, 291–304 (2019). https://doi.org/10.1016/j.surfcoat.2019.05.056
Prasad, C.D., Joladarashi, S., Ramesh, M.R., Srinath, M.S., Channabasappa, B.H.: Development and sliding wear behavior of Co-Mo-Cr-Si Cladding through Microwave Heating. Silicon, Springer. 11, 2975–2986 (2019). https://doi.org/10.1007/s12633-019-0084-5
Prasad, C.D., Joladarashi, S., Ramesh, M.R., Srinath, M.S., Channabasappa, B.H.: Microstructure and Tribological Behavior of Flame Sprayed and Microwave Fused CoMoCrSi/CoMoCrSi-Cr3C2 Coatings. Mater. Res. Express. 6, 026512 (2019). https://doi.org/10.1088/2053-1591/aaebd9
Prasad, C.D., Joladarashi, S., Ramesh, M.R., Srinath, M.S., Channabasappa, B.H.: Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi Coating. Mater. Res. Express. 5, 086519 (2018). https://doi.org/10.1088/2053-1591/aad44e
Durga Prasad, C., Joladarashi, S., Ramesh, M.R.: Anunoy Sarkar. “High Temperature Gradient Cobalt based Clad Developed Using Microwave Hybrid Heating”. American Institute of Physics, 1943, 020111 (2018). https://doi.org/10.1063/1.5029687
Girisha, K.G., Sreenivas Rao, K.V., Prasad, D.: C, “Slurry Erosion Resistance of Martenistic Stainless Steel with Plasma Sprayed Al2O3-40%TiO2 Coatings”, Materials Today Proceedings 5 7388–7393. (2018). https://doi.org/10.1016/j.matpr.2017.11.409
Girisha, K.G., Durga Prasad, C., Anil, K.C., Sreenivas Rao, K.V.: Dry sliding wear behaviour of Al2O3 coatings for AISI 410 grade stainless steel. Appl. Mech. Mater. 766–767, 585–589 (2015). https://doi.org/10.4028/www.scientific.net/AMM.766-767.585
Girisha, K.G., Rakesh, R., Durga Prasad, C., Sreenivas Rao, K.V.: Development of corrosion resistance coating for AISI 410 grade steel. Appl. Mech. Mater. 813–814, 135–139 (2015). https://doi.org/10.4028/www.scientific.net/AMM.813-814.135
Acknowledgements
We would like to thanks the Visvesvarya Technology University (VTU) regional research center, Department of Mechanical Engineering, RV college of Engineering Bengaluru, Karnataka-india for providing facilities to conduct this research work.
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
Competing interests
This article has not been submitted elsewhere for publication and authors do not have any conflict related to this manuscript and presented data.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Kattimani, M.A., Venkatesh, P.R., Masum, H. et al. Design and numerical analysis of tensile deformation and fracture properties of induction hardened inconel 718 superalloy for gas turbine applications. Int J Interact Des Manuf (2023). https://doi.org/10.1007/s12008-023-01452-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12008-023-01452-z