Skip to main content
SpringerLink
Log in

Effects of PCB Pad Metal Finishes on the Cu-Pillar/Sn-Ag Micro Bump Joint Reliability of Chip-on-Board (COB) Assembly

  • Published:
Journal of Electronic Materials Aims and scope Submit manuscript

Abstract

While solder bumps have been used as the bump structure to form the interconnection during the last few decades, the continuing scaling down of devices has led to a change in the bump structure to Cu-pillar/Sn-Ag micro-bumps. Cu-pillar/Sn-Ag micro-bump interconnections differ from conventional solder bump interconnections in terms of their assembly processing and reliability. A thermo-compression bonding method with pre-applied b-stage non-conductive films has been adopted to form solder joints between Cu pillar/Sn-Ag micro bumps and printed circuit board vehicles, using various pad metal finishes. As a result, various interfacial inter-metallic compounds (IMCs) reactions and stress concentrations occur at the Cu pillar/Sn-Ag micro bumps joints. Therefore, it is necessary to investigate the influence of pad metal finishes on the structural reliability of fine pitch Cu pillar/Sn-Ag micro bumps flip chip packaging. In this study, four different pad surface finishes (Thin Ni ENEPIG, OSP, ENEPIG, ENIG) were evaluated in terms of their interconnection reliability by thermal cycle (T/C) test up to 2000 cycles at temperatures ranging from −55°C to 125°C and high-temperature storage test up to 1000 h at 150°C. The contact resistances of the Cu pillar/Sn-Ag micro bump showed significant differences after the T/C reliability test in the following order: thin Ni ENEPIG > OSP > ENEPIG where the thin Ni ENEPIG pad metal finish provided the best Cu pillar/Sn-Ag micro bump interconnection in terms of bump joint reliability. Various IMCs formed between the bump joint areas can account for the main failure mechanism.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. J. Osenbach, S. Emerich, S. Cate, D. Brady, S.M. Hwang, J. Dang, and D. Crouthamel, in Proceedings of IEEE 64th Electronic Components and Technology Conference (ECTC), pp. 74–80 (2014)

  2. J.W. Shin, Y.W. Choi, Y.S. Kim, and K.W. Paik, in Proceedings of IEEE Electronic Components and Technology Conference (ECTC), pp. 31–35 (2012)

  3. Y.W. Choi, J.W. Shin, and K.W Paik, in Proceedings of Electronic Components and Technology Conference, pp. 1126–1129 (2011)

  4. S.H. Hwang, B.J. Kim, H.Y. Lee, and Y.C. Joo, J. Electron. Mater. 41, 232 (2012).

    Article  Google Scholar 

  5. S. Lee and D. Baldwin, in Surface Mount Technology Association, pp. 525–530 (2007)

  6. T.M Niu, B. Sammakia, and S. Sathe, in Proceedings of Thermal Thermomechanical Phenomena in Electronic Systems, pp. 251–258 (1998)

  7. M. Yunus, K. Srihari, J.M. Pitarresi, and A. Primavera, in Proceedings of IEEE/CPMT International Electronics Manufacturing Technology Symposium, pp. 207–213 (2000)

  8. B. Arfaei, F. Mutuku, K. Sweatman, N.-C. Lee, E. Cotts, and R. Coyle, in Proceedings of Electronic Components and Technology Conference, pp. 655–665 (2014)

  9. W.H. Wu, S. Wei, Y.C. Lin, and C.E. Ho, Procedia Eng. 36, 419 (2012).

    Article  Google Scholar 

  10. R. Ramanauskas, A. Selskis, J. Juodkazyte, and V. Jasulaitiene, Circuit World 39, 124 (2013).

    Article  Google Scholar 

  11. W.H. Wu, C.S. Lin, S.H. Huang, and C.E. Ho, J. Electron. Mater. 39, 2387 (2010).

    Article  Google Scholar 

  12. A. Kumar, Z. Chen, S.G. Mhaisalkar, C.C. Wong, P.S. Teo, and V. Kripesh, Thin Solid Films 504, 410 (2006).

    Article  Google Scholar 

  13. A. Kumar, M. He, and Z. Chen, Surf. Coat. Technol. 198, 283 (2005).

    Article  Google Scholar 

  14. T. Laurila, V. Vuorinen, and J.K. Kivilahti, Mater. Sci. Eng. R 49, 1 (2005).

    Article  Google Scholar 

  15. J.M. Song, Y.R. Liu, Y.S. Lai, Y.T. Chiu, and N.C. Lee, Microelectron. Reliab. 52, 180 (2012).

    Article  Google Scholar 

  16. C.Y. Li and J.G. Duh, J. Mater. Res. 20, 3118 (2005).

    Article  Google Scholar 

  17. B. Chao, S.H. Chae, X. Zhang, K.H. Lu, J. Im, and P.S. Ho, Acta Mater. 55, 2805 (2007).

    Article  Google Scholar 

  18. M. Tanaka, T. Sasaki, T. Kobayashi, and K. Tatsumi, in Proceedings of Electronic Components and Technology Conference, pp. 78–84 (2006)

Download references

Author information

Authors and Affiliations

  1. Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 373-1, Gu-seong dong, Yu-seong gu, Daejeon, 305-701, Korea

    Youngsoon Kim, Seyong Lee, Ji-won Shin & Kyung-Wook Paik

Authors
  1. Youngsoon Kim
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Seyong Lee
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Ji-won Shin
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Kyung-Wook Paik
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Kyung-Wook Paik.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Kim, Y., Lee, S., Shin, Jw. et al. Effects of PCB Pad Metal Finishes on the Cu-Pillar/Sn-Ag Micro Bump Joint Reliability of Chip-on-Board (COB) Assembly. J. Electron. Mater. 45, 3208–3219 (2016). https://doi.org/10.1007/s11664-016-4427-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11664-016-4427-3

Keywords

Search

Navigation