Abstract
Background
Correct positioning of pedicle screws can be challenging. Intraoperative imaging may be helpful. The purpose of this study was to evaluate the use of intraoperative 3D imaging with a cone-beam CT. The hypotheses were that intraoperative 3D imaging (1) will lead to an intraoperative revision of pedicle screws and (2) may diminish the rate of perforated screws on postoperative imaging.
Methods
Totally, 351 patients (age 60.9 ± 20.3 a (15–96); m/f 203/148) underwent dorsal instrumentation with intraoperative 3D imaging with 2215 pedicle screws at a trauma center level one. This study first evaluates intraoperative imaging. After this, 501 screws in 73 patients (age 62.5 ± 19.7 a; m/f 47/26) of this collective were included in the study group (SG) and their postoperative computed tomography was evaluated with regard to screw position. Then, 500 screws in 82 patients (age 64.8 ± 14.4 a; m/f 51/31) as control group (CG), who received the screws with conventional 2D fluoroscopy but without 3D imaging, were evaluated with regard to screw position.
Results
During the placement of the 2215 pedicle screws, 158 (7.0%) intraoperative revisions occurred as a result of 3D imaging. Postoperative computed tomography of the SG showed 445 (88.8%) screws without relevant perforation (type A + B), of which 410 (81.8%) could be classified as type A and 35 (7.0%) could be classified as type B. Fifty-six (11.2%) screws in SG showed relevant perforation (type C–E). In contrast, 384 (76.8%) screws in the CG were without relevant perforation (type A + B), of which 282 (56.4%) could be classified as type A and 102 (20.4%) as type B. One hundred and sixteen (23.2%) screws in the CG showed relevant perforation (type C–E).
Conclusion
This study shows that correct placement of pedicle screws in spine surgery with conventional 2D fluoroscopy is challenging. Misplacement of screws cannot always be prevented. Intraoperative 3D imaging with a CBCT can be helpful to detect and revise misplaced pedicle screws intraoperatively. The use of intraoperative 3D imaging will probably minimize the number of revision procedures due to perforating pedicle screws.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Background
The current gold standard for the surgical therapy of spinal fractures, in degenerative and in the majority of congenital diseases, is the dorsal instrumentation of the spine using pedicle screws [1, 2]. One difficulty in inserting screws in the spine is their correct placement in the pedicle without perforating medially or laterally. Misplaced pedicle screws after dorsal instrumentation are observed in between 1.5 and 40% of cases in the current literature [3,4,5]. However, this is of particular importance due to the adjacent structures. Ideally, the screw should be centrally located in the pedicle without tangentially affecting or perforating the pedicle cortex. While lateral malpositioning of the pedicle screw may affect the stability, medial perforation of the pedicle screw may be associated with severe neurologic impairment. Despite this anatomic proximity, injuries of these important nervous structures are rarely observed. Esses et al. observed temporary neurologic impairment in 2.4% and persistent neurologic damage in 2.3% of their 617 surgically treated patients [5]. Moreover, the screw tip should lie in the vertebral body, but without penetrating the ventral cortex. This is also very important if adjacent organs (e.g., aorta, vena cava, lung, trachea, esophagus, etc.) and blood vessels are present, which can be injured intraoperatively. Fortunately, this rarely happens [3, 6,7,8].
Consequently, it is necessary to check and assess the pedicle screw position intraoperatively, for which Gertzbein–Robbins et al. developed their classification (A–E) of pedicle screw position [9]. Deviations > 2 mm outside the pedicle are classified as type C according to Gertzbein–Robbins [9] and are considered to need correction [10], even if no neurologic damage is to be expected with medial deviations up to 4 mm [11]. At the same time, however, it must be taken into account that the thoracic pedicles are commonly < 4 mm wide, so that even thin pedicle screws can perforate the pedicle in this area [12]. Even though the Gertzbein–Robbins classification facilitates the assessment of the screw position, the practical implementation in the operating room with the aid of conventional 2D fluoroscopy remains highly challenging or, in some cases, gives great residual uncertainty. Therefore, computed tomography is recommended to assess screw positioning and reduction [1, 11, 13, 14]. Intraoperative availability of computed tomography is low. Screw malpositioning or inadequate reduction detected on postoperative computed tomography may necessitate revision surgery. Accordingly, intraoperative 3D imaging with cone-beam CT (CBCT) has been developed to close this gap and to facilitate intraoperative assessment. The advantage of CBCT imaging has been demonstrated in other anatomic regions [15]. The purpose of this retrospective study was to evaluate the intraoperative revision rate, revision reason, and postoperative result of pedicle screw implantations after 3D imaging with CBCT. The hypotheses were that the use of intraoperative 3D imaging to analyze the pedicle screw placement in dorsal instrumentation (1) will lead to intraoperative revision of pedicle screws and (2) may reduce the rate of misplaced screws on postoperative imaging.
Methods
This study obtained approval from the local ethics committee (Reference no. 2020-15452-retrospektiv). A total of 351 patients (age 60.9 ± 20.3 (15–96) y; male/female 203/148) underwent dorsal instrumentation with intraoperative 3D imaging at a trauma center level one between January 2013 and August 2020. The patients were placed in the prone position during surgery. The pedicle screws were inserted percutaneously through small skin incisions in free-hand technique cannulated over pre-inserted Kirschner wires (K-wires). Intraoperatively, the K-wires or screw position and reduction were assessed under 2D fluoroscopy as usual. Only if the results were satisfactory, 3D imaging with a CBCT was performed. Two different CBCT models were used for this: Cios Spin (Siemens, Erlangen, Germany) and ARCADIS Orbic 3D (Siemens, Erlangen, Germany). While Cios Spin is a 3D C-arm with a flat panel, the ARCADIS Orbic is a 3D fluoroscopy with an image intensifier‐based 3D imaging C‐arm.
Technically, these devices rotate around the spine and automatically capture a series of 2D images. Image generation on the ARCADIS Orbic is based on analog image intensifier technology, with limitations in the area of acquired image data, contrast differences, and susceptibility to artifacts. Since pedicle screws are relatively large compared to the anatomic structures being examined, artifacts can significantly complicate image assessment. Accordingly, to improve image quality and reduce susceptibility to artifacts, new flat panel detectors have been developed and are used in the newer flat panel C-arm generations. [16].
Coronal, sagittal, and axial projections allowed the reduction and placement of screws to be evaluated. Image assessment can be performed either slice by slice or on a reconstructed 3D model, as usual when assessing CT imaging.
The CBCT scans obtained were evaluated immediately after imaging. Pedicle screw location was assessed using the Gertzbein–Robbins classification [9] modified from Schatlo et al. [17]. Pedicle screws with a deviation of more than 2 mm (Gertzbein–Robbins type C–E) according to Schatlo et al. [17] outside the pedicle were classified as perforated and in need of intraoperative revision. The findings were documented intraoperatively in an Excel spreadsheet (Microsoft, Redmond, USA) immediately after evaluation. If malpositioned pedicle screws (Gertzbein–Robbins type C–E [17]) were detected in the CBCT scans, they were corrected accordingly. And in the case of immediate intraoperative revision, the same sequence of intraoperative imaging was followed as before: 2D fluoroscopy and then intraoperative 3D imaging. The collected findings were then reassessed and documented. This procedure was continued until a satisfactory result was determined in the intraoperative 3D imaging.
A pedicle perforating screw placement with dislocation > 2 mm (Gertzbein–Robbins type C–E) was a reason for surgical revision.
Postoperative computed tomography (Aquilion Prime SP and Aquilion Lightning, Canon, Tokyo, Japan) was performed to verify the surgical outcome.
As a control group (CG), 82 patients (age 64.8 ± 14.4 a; m/f 51/31) with a total of 500 screws, who received dorsal instrumentation with conventional fluoroscopy without 3D imaging in the same time period, were included.
In this study, we retrospectively evaluated the intraoperatively created database of the intraoperative 3D imaging with CBCT. After that, we evaluated the postoperative computed tomography results of SG and CG. In both groups, we analyzed the pedicle screw position on postoperative computed tomography using Gertzbein–Robbins–Robbins classification [9] modified from Schatlo et al. [17] (Fig. 1).
Assessment of the pedicle screw position using the Gertzbein–Robbins–Robbins classification [9]. Marking of the bony pedicle borders by an ellipse. Then determine the maximum screw distance from the (in this case lateral) pedicle border
The normality of the continuous data was assessed, and the data are presented as the means ± standard deviations (ranges). Wilcoxon tests were used to assess the differences between the study group and the control group. All analyses were performed using SAS. The significance level was set at 0.05.
Results
During the placement of the 2215 pedicle screws in a total of 351 patients between January 2013 and August 2020, 437 CBCT scans were performed. Eighty-six patients received multiple intraoperative CBCT scans, with a maximum of two CBCT scans in one surgery. In all patients, the intraoperative 3D imaging was performed for diagnostic reasons and not due to complications. In summary, a total of 158 (7.0%) intraoperative revisions were made intraoperatively based on the intraoperative 3D imaging (Table 1).
Evaluation of postoperative computed tomography of the SG showed non-relevant perforating of the screws (Gertzbein–Robbins type A + B) in 445 (88.8%) cases, of which 410 (81.8%) cases could be classified as type A and 35 (7.0%) cases could be classified as type B. Fifty-six (11.2%) of 501 pedicle screws showed relevant perforation of the pedicle (Gertzbein–Robbins type C–E).
In contrast, 384 (76.8%) screws in the CG were without relevant perforation (Gertzbein–Robbins type A + B), of which 282 (56.4%) could be classified as type A and 102 (20.4%) screws as type B. One hundred and sixteen (23.2%) screws in CG showed relevant perforation (Gertzbein–Robbins type C–E).
The majority of pedicle screws in both SG and CG were inserted in the thoracic segments of the spine (Table 2).
The difference between the numbers of screws without relevant perforation (Gertzbein–Robbins type A + B) in the SG and CG was statistically significant (p < 0.0001). However, there was no statistically significant difference between the numbers of screws with relevant perforation in the SG and CG (p < 0.8791).
Of the 56 screws in SG with relevant pedicle perforation (Gertzbein–Robbins type C–E) on postoperative computed tomography, 26 screws showed medial deviation (2.9 ± 0.9 mm) and 29 screws showed lateral deviation (3.0 ± 1.1 mm) from the pedicle. One screw breached out caudally (2 mm). No screw showed cranial deviation.
In the postoperative imaging of the 116 pedicle perforating screws of the CG in the postoperative imaging, 45 screws showed medial deviation (2.6 ± 0.6 mm) and 70 screws showed lateral deviation (3.2 ± 1.2 mm) from the pedicle. Again, one screw breached out caudally (2 mm) and no screw showed a cranial deviation.
Discussion
The purpose of this retrospective study was to evaluate the intraoperative revision rate because of 3D imaging and postoperative result of pedicle screw implantations in dorsal instrumentation with and without 3D imaging. The hypotheses were that the use of intraoperative 3D imaging as part of dorsal instrumentation in spine surgery (1) will lead to intraoperative revision of pedicle screws and (2) may reduce the rate of misplaced screws on postoperative imaging.
In our study, a total of 158 (7.0%) of 2215 implanted pedicle screws were not correctly positioned using conventional 2D fluoroscopy-assisted dorsal instrumentation and were revised as a result of intraoperative 3D imaging with cone-beam CT during the primary procedure. On postoperative computed tomography, 56 (11.2%) of 500 implanted pedicle screws in SG with intraoperative 3D imaging were still with relevant pedicle perforation (Gertzbein–Robbins type C–E). Conversely, in CG without intraoperative 3D imaging 116 (23.2%) screws remained with relevant pedicle perforation. Accordingly, intraoperative 3D imaging may reduce the rate of misplaced pedicle screws on postoperative CT imaging.
Assessment of pedicle screw placement in dorsal instrumentation on conventional 2D fluoroscopy imaging is a major challenge even for the experienced surgeon [13]. Berlemann et al. were able to show that 59% of all incorrectly positioned pedicle screws are missed in 2D fluoroscopy imaging compared with computed tomography imaging [14]. Accordingly, computed tomography can be seen as the gold standard in the assessment of pedicle screw location [1, 11, 13, 14]. However, if a finding requiring revision only becomes visible on postoperative computed tomography, then a revision operation is necessary. This can be circumvented with intraoperative 3D imaging. The availability of intraoperative computed tomography is low, so that 2D methods, from which 3D images can be calculated, are increasingly used intraoperatively to close this gap. This includes cone-beam CT (CBCT). The positive effect of the intraoperative application of CBCT has already been demonstrated in other anatomic regions [15].
Three different methods of implanting pedicle screws are described in the current literature: free-hand technique, with the aid of fluoroscopy, or in a navigated technique.
Malposition rates (1.7–31%) in postoperative computed tomography with free-hand technique can be significant [18, 19], whereas the use of conventional 2D fluoroscopy to check screw position intraoperatively may not improve the rate of screws fully contained in the pedicle (28–85%) [18]. To prevent screw misplacement, navigation systems have been developed using 3D fluoroscopic or CT imaging to achieve better results [20, 21]. Revision rates because of misplaced screws have also been reduced by 3D navigation. This is illustrated by studies that discovered three times higher revision rates for non-navigated techniques compared to 3D navigation [20]. Both CT-navigated and fluoroscopy-navigated techniques show better postoperative results. In the review by Gelalis et al., rates of 89–100% and 81–92%, respectively, of screws fully contained in the pedicle were reported [18]. Moreover, Takahata et al. implanted a total of 166 CBCT-navigated pedicle screws in a collective of 48 consecutive patients with a rate of 2.4% misplaced pedicle screws [21]. These data indicate that intraoperative 3D navigation provides greater accuracy in pedicle screw insertion than the free-hand technique and conventional 2D fluoroscopy.
Advantages of the non-navigated technique with intraoperative 3D imaging generated with CBCT are that it is more readily available and less expensive compared to the navigated technique. In addition, compared to the non-navigated technique, preparation of the navigated technique in surgery extends the operating time by a few minutes [22]. 3D imaging with CBCT also extends the operating time—even if only slightly—compared to conventional fluoroscopy, which has already been shown in the current literature [23, 24]. In the context of this study, the time of the CBCT examination was not explicitly investigated, but was determined in an in-house investigation earlier which showed that the procedure is extended by approximately 5 min due to 3D imaging. Furthermore, the non-navigated technique with intraoperative 3D imaging does not have such a flat learning curve as the navigated technique, so it can be integrated into the clinical routine more quickly.
Little data are available in the literature concerning the non-navigated technique supported with 3D imaging with CBCT that we use. Cordemans et al. performed a study to verify pedicle screw position with intraoperative 3D imaging using CBCT. They implanted a total of 695 screws in 118 patients. The rate of pedicle breaching screws on intraoperative CBCT was 11.7% in their collective [25].
In addition, further studies demonstrated that intraoperative 3D imaging with a CBCT is not inferior to established computed tomography. The authors concluded that intraoperative CBCT could replace postoperative computed tomography after dorsal instrumentation in the future [26, 27].
A disadvantage of 3D imaging with CBCT compared to conventional fluoroscopy is the higher radiation exposure caused by 3D imaging [28], which is certainly not negligible. Nevertheless, in our opinion, the advantage of the increased accuracy of screw positioning is superior to the disadvantage of the increased radiation exposure compared to conventional fluoroscopy.
Based on the 3D imaging generated with the CBCT, a sufficient assessment of the pedicle screw position can be made and a not-to-be-underestimated number of perforating screws can be detected intraoperatively, as is evident from our results and the current literature. Accordingly, in our view, intraoperative 3D imaging with a CBCT in the context of dorsal instrumentation is a good alternative to the navigated technique or postoperative computed tomography with regard to the radiologic results of pedicle screw position.
However, the results of this study must be interpreted in light of several limitations: (1) This is a retrospective evaluation of intraoperatively generated 3D imaging. (2) Only the radiologic results of intraoperative 3D imaging were assessed but not the clinical outcomes, and so it is not clear to what extent a nonoptimal pedicle screw position in the postoperative computed tomography affects the outcome. However, since none of the misplaced screws were revised following postoperative CT imaging, it can be assumed that they were not clinically relevant. (3) In the study, two different CBCTs were used for intraoperative 3D imaging: Cios Spin (Siemens, Erlangen, Germany) and ARCADIS Orbic 3D (Siemens, Erlangen, Germany). The quality of imaging acquired from the Cios Spin was superior to that of the ARCADIS Orbic 3D. Even though the radiologic evaluation of the imaging did not show any influence of the type of CBCT on the result, a certain influence cannot be excluded with absolute certainty. In our view, the ethical duty to provide optimal patient care made it impossible to omit intraoperative 3D imaging for pure study reasons.
Conclusion
This study shows that correct placement of pedicle screws in spine surgery with conventional 2D fluoroscopy is challenging. Misplacement of screws cannot always be prevented. Intraoperative 3D imaging with a CBCT can be helpful to detect and revise misplaced pedicle screws intraoperatively. The use of intraoperative 3D imaging will probably minimize the number of revision procedures due to perforating pedicle screws.
Availability of data and materials
The datasets used and analyzed during the current study are available from the corresponding author on reasonable request.
References
Bauer JM, Moore JA, Rangarajan R, Gibbs BS, Yorgova PK, Neiss GI, et al. Intraoperative CT scan verification of pedicle screw placement in AIS to prevent malpositioned screws: safety benefit and cost. Spine Deform. 2018;6:662–8. https://doi.org/10.1016/j.jspd.2018.04.010.
Beck M, Mittlmeier T, Gierer P, Harms C, Gradl G. Benefit and accuracy of intraoperative 3D-imaging after pedicle screw placement: a prospective study in stabilizing thoracolumbar fractures. Eur Spine J. 2009;18:1469–77. https://doi.org/10.1007/s00586-009-1050-5.
Di Silvestre M, Parisini P, Lolli F, Bakaloudis G. Complications of thoracic pedicle screws in scoliosis treatment. Spine (Phila Pa 1976). 2007;32:1655–61. https://doi.org/10.1097/BRS.0b013e318074d604.
Castro WH, Halm H, Jerosch J, Malms J, Steinbeck J, Blasius S. Accuracy of pedicle screw placement in lumbar vertebrae. Spine (Phila Pa 1976). 1996;21:1320–4. https://doi.org/10.1097/00007632-199606010-00008.
Esses SI, Sachs BL, Dreyzin V. Complications associated with the technique of pedicle screw fixation. A selected survey of ABS members. Spine (Phila Pa 1976). 1993;18:2231–8. https://doi.org/10.1097/00007632-199311000-00015 (discussion 2238-9).
O’Brien JR, Krushinski E, Zarro CM, Sciadini M, Gelb D, Ludwig S. Esophageal injury from thoracic pedicle screw placement in a polytrauma patient: a case report and literature review. J Orthop Trauma. 2006;20:431–4. https://doi.org/10.1097/00005131-200607000-00012.
Cardoso MJ, Helgeson MD, Paik H, Dmitriev AE, Lehman RA, Rosner MK. Structures at risk from pedicle screws in the proximal thoracic spine: computed tomography evaluation. Spine J. 2010;10:905–9. https://doi.org/10.1016/j.spinee.2010.08.020.
Suk SI, Kim WJ, Lee SM, Kim JH, Chung ER. Thoracic pedicle screw fixation in spinal deformities: are they really safe? Spine (Phila Pa 1976). 2001;26:2049–57. https://doi.org/10.1097/00007632-200109150-00022.
Gertzbein SD, Robbins SE. Accuracy of pedicular screw placement in vivo. Spine (Phila Pa 1976). 1990;15:11–4. https://doi.org/10.1097/00007632-199001000-00004.
Aoude AA, Fortin M, Figueiredo R, Jarzem P, Ouellet J, Weber MH. Methods to determine pedicle screw placement accuracy in spine surgery: a systematic review. Eur Spine J. 2015;24:990–1004. https://doi.org/10.1007/s00586-015-3853-x.
Laine T, Mäkitalo K, Schlenzka D, Tallroth K, Poussa M, Alho A. Accuracy of pedicle screw insertion: a prospective CT study in 30 low back patients. Eur Spine J. 1997;6:402–5. https://doi.org/10.1007/BF01834068.
Lien S-B, Liou N-H, Wu S-S. Analysis of anatomic morphometry of the pedicles and the safe zone for through-pedicle procedures in the thoracic and lumbar spine. Eur Spine J. 2007;16:1215–22. https://doi.org/10.1007/s00586-006-0245-2.
Farber GL, Place HM, Mazur RA, Jones DE, Damiano TR. Accuracy of pedicle screw placement in lumbar fusions by plain radiographs and computed tomography. Spine (Phila Pa 1976). 1995;20:1494–9. https://doi.org/10.1097/00007632-199507000-00010.
Berlemann U, Heini P, Müller U, Stoupis C, Schwarzenbach O. Reliability of pedicle screw assessment utilizing plain radiographs versus CT reconstruction. Eur Spine J. 1997;6:406–10. https://doi.org/10.1007/BF01834069.
Beisemann N, Keil H, Swartman B, Schnetzke M, Franke J, Grützner PA, Vetter SY. Intraoperative 3D imaging leads to substantial revision rate in management of tibial plateau fractures in 559 cases. J Orthop Surg Res. 2019;14:236. https://doi.org/10.1186/s13018-019-1286-7.
Keil H, Luxenhofer M, Vetter SY, Beisemann N, Grützner PA, Franke J. Evaluation of image quality and assessability of a new flat-panel 3D C-arm compared to mobile and fixed computed tomography in posterior spinal fixation. Int J Med Robot. 2021;17:e2181. https://doi.org/10.1002/rcs.2181.
Schatlo B, Molliqaj G, Cuvinciuc V, Kotowski M, Schaller K, Tessitore E. Safety and accuracy of robot-assisted versus fluoroscopy-guided pedicle screw insertion for degenerative diseases of the lumbar spine: a matched cohort comparison. J Neurosurg Spine. 2014;20:636–43. https://doi.org/10.3171/2014.3.SPINE13714.
Gelalis ID, Paschos NK, Pakos EE, Politis AN, Arnaoutoglou CM, Karageorgos AC, et al. Accuracy of pedicle screw placement: a systematic review of prospective in vivo studies comparing free hand, fluoroscopy guidance and navigation techniques. Eur Spine J. 2012;21:247–55. https://doi.org/10.1007/s00586-011-2011-3.
Parker SL, McGirt MJ, Farber SH, Amin AG, Rick A-M, Suk I, et al. Accuracy of free-hand pedicle screws in the thoracic and lumbar spine: analysis of 6816 consecutive screws. Neurosurgery. 2011;68:170–8. https://doi.org/10.1227/NEU.0b013e3181fdfaf4 (discussion 178).
Fichtner J, Hofmann N, Rienmüller A, Buchmann N, Gempt J, Kirschke JS, et al. Revision rate of misplaced pedicle screws of the thoracolumbar spine-comparison of three-dimensional fluoroscopy navigation with freehand placement: a systematic analysis and review of the literature. World Neurosurg. 2018;109:e24–32. https://doi.org/10.1016/j.wneu.2017.09.091.
Takahata M, Yamada K, Akira I, Endo T, Sudo H, Yokoyama H, Iwasaki N. A novel technique of cervical pedicle screw placement with a pilot screw under the guidance of intraoperative 3D imaging from C-arm cone-beam CT without navigation for safe and accurate insertion. Eur Spine J. 2018;27:2754–62. https://doi.org/10.1007/s00586-018-5706-x.
Balling H. Time demand and radiation dose in 3D-fluoroscopy-based navigation-assisted 3D-fluoroscopy-controlled pedicle screw instrumentations. Spine (Phila Pa 1976). 2018;43:E512–9. https://doi.org/10.1097/BRS.0000000000002422.
Braak SJ, Zuurmond K, Aerts HCJ, van Leersum M, Overtoom TTT, van Heesewijk JPM, van Strijen MJL. Feasibility study of needle placement in percutaneous vertebroplasty: cone-beam computed tomography guidance versus conventional fluoroscopy. Cardiovasc Intervent Radiol. 2013;36:1120–6. https://doi.org/10.1007/s00270-013-0598-y.
Privalov M, Beisemann N, Swartman B, Vetter SY, Grützner PA, Franke J, Keil H. First experiences with intraoperative CT in navigated sacroiliac (SI) instrumentation: an analysis of 25 cases and comparison with conventional intraoperative 2D and 3D imaging. Injury. 2020. https://doi.org/10.1016/j.injury.2020.02.093.
Cordemans V, Kaminski L, Banse X, Francq BG, Detrembleur C, Cartiaux O. Pedicle screw insertion accuracy in terms of breach and reposition using a new intraoperative cone beam computed tomography imaging technique and evaluation of the factors associated with these parameters of accuracy: a series of 695 screws. Eur Spine J. 2017;26:2917–26. https://doi.org/10.1007/s00586-017-5195-3.
Cordemans V, Kaminski L, Banse X, Francq BG, Cartiaux O. Accuracy of a new intraoperative cone beam CT imaging technique (Artis zeego II) compared to postoperative CT scan for assessment of pedicle screws placement and breaches detection. Eur Spine J. 2017;26:2906–16. https://doi.org/10.1007/s00586-017-5139-y.
Burström G, Cewe P, Charalampidis A, Nachabe R, Söderman M, Gerdhem P, et al. Intraoperative cone beam computed tomography is as reliable as conventional computed tomography for identification of pedicle screw breach in thoracolumbar spine surgery. Eur Radiol. 2020. https://doi.org/10.1007/s00330-020-07315-5.
Donnell C, Maertens A, Bompadre V, Wagner TA, Krengel W. Comparative radiation exposure using standard fluoroscopy versus cone-beam computed tomography for posterior instrumented fusion in adolescent idiopathic scoliosis. Spine (Phila Pa 1976). 2014;39:E850–5. https://doi.org/10.1097/BRS.0000000000000363.
Funding
The research group had grants/grants pending and technical support from Siemens Healthineers (Erlangen, Germany). Siemens had no involvement in the study design, collection, analysis, and interpretation of data, the writing of the manuscript, and the decision to submit the manuscript for publication.
Author information
Authors and Affiliations
Contributions
FZ and SV wrote the manuscript. KH and FZ evaluated the data. SV developed the concept and supervised the study. MP and JF supervised the study and assisted with the concept. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethical approval and consent for participate
Ethics approval was given by the Committee of Medical Association of Rhineland Palatinate, Mainz, Germany (Reference no. 2020-15452).
Competing interests
JF is a paid member of an advisory board for Siemens. FZ, KK, MP, and SV declare that they have no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.
About this article
Cite this article
Zimmermann, F., Kohl, K., Privalov, M. et al. Intraoperative 3D imaging with cone-beam computed tomography leads to revision of pedicle screws in dorsal instrumentation: a retrospective analysis. J Orthop Surg Res 16, 706 (2021). https://doi.org/10.1186/s13018-021-02849-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13018-021-02849-w