The role of a graphite layer on the surface of ceramics based on tetragonal zirconia, partially stabilized by yttrium oxide (Y–TZP-ceramics) under the action of a pulsed laser was studied using original methodology. It has been found that surface graphitization increases the fraction of absorbed laser radiation, and as a result, heating, melting and evaporation of Y–TZP-ceramics occur under less intense modes, favorably affecting the use of pulsed laser radiation for surface modification.
Similar content being viewed by others
References
Bikramjit Basu, Jozef Vleugels, Omer Van Der Biest, “Microstructure-toughness-wear relationship of tetragonal zirconia ceramics,” J. Eur. Ceram. Soc., 24, 2031 – 2040 (2004).
G. K. R. Pereira, S. Fraga, and A. F. Montagnera, “The effect of grinding on the mechanical behavior of Y–TZP ceramics: A systematic review and meta-analyses,” J. Mech. Behav. Biomed., 63, 417 – 442 (2016).
T. A. Dantas, S. Roedel, P. Flores, et al., “Wear behaviour of tetragonal zirconia polycrystal with a porous surface,” Int. J. Refract. Met. Hard Mater., 75, 85 – 93 (2018).
V. V. Kuzin, S. Yu. Fedorov, and S. N. Grigor’ev, “Correlation of diamond grinding regime with surface condition of ceramic based on zirconium dioxide,” Refract. Ind. Ceram., 57(6), 625 – 630 (2017).
V. V. Kuzin, S. Yu. Fedorov, and S. N. Grigor’ev, “Level of Y–TZP-ceramic specimen edge defects after diamond machining,” Refract. Ind. Ceram., 58(4), 415 – 417 (2017).
Walter Harrer, Marco Deluca, and Roger Morrell, “Failure analysis of a ceramic ball race bearing made of Y–TZP zirconia,” Eng. Fail. Anal., 36, 262 – 268 (2014).
H. K. Tönshoff and H. Kappel, “Surface Modification of Ceramics by Laser Machining,” CIRP Annals, 47, 471 – 474 (1998).
Susmita Bose, Samuel Ford Robertson, and Amit Bandyopadhyay, “Surface modification of biomaterials and biomedical devices using additive manufacturing,” Acta Biomater., 66, 6 – 22 (2018).
Lerato Criscelda Tshabalala and Sisa Pityana, “Surface texturing of Si3N4–SiC ceramic tool components by pulsed laser machining,” Surface and Coatings Technology, 289, 52 – 60 (2016).
C. G. Moura, R. Pereira, M. Buciumeanu, et al., “Effect of laser surface texturing on primary stability and surface properties of zirconia implants,” Ceram. Int., 43, 15227 – 15236 (2017).
V. Kuzin, S. Grigoriev, M. Fedorov, et al., “Surface modification of zirconia (Y–TZP) ceramics induced by pulsed laser machining,” Appl. Mech. Mater., 752 – 753, 481 – 484 (2015).
E. Roitero, F. Lasserre, J. J. Roa, et al., “Nanosecond-laser patterning of 3Y–TZP: Damage and microstructural changes,” J. Eur. Ceram. Soc., 37, 4876 – 4887 (2017).
V. V. Kuzin, “Oxide ceramic surface layer modification using continuous laser radiation,” Refract. Ind. Ceram., 57(1), 53 – 57 (2016).
Erica Roitero, Federico Lasserre, Marc Anglada, et al., “A parametric study of laser interference surface patterning of dental zirconia: Effects of laser parameters on topography and surface quality,” Dental Materials, 33, e28 – e38 (2017).
S. V. Vasilyev, A. Yu. Ivanov, and V. I. Nedolgov, “The influence of non-destructive effects of laser radiation on the composition and physicochemical properties of the surface metal layer” [in Russian], Vestnik Grodn. Gos. Un-ta im. Yanki Kupaly. Ser. 2. Matematika. Fizika. Informatika, Vychislitel’naya Tekhnika i Upravlenie, 78 – 80 (2001).
Laser Technologies for Processing Materials: Current Problems of Basic Research and Applied Research [in Russian], ed. V. Ya. Panchenko, Fizmatlit, Moscow (2009) 664 p.
V. Kuzin, S. Grigoriev, and M. Portnoy, “Effect of thermal loading on stresses in defective surface layer of ceramics,” Appl. Mech. Mater., 827, 189 – 192 (2016).
V. V. Kuzin, S. N. Grigor’ev, and V. N. Ermolin, “Stress inhomogeneity in a ceramic surface layer under action of an external load. Part 2. Effect of thermal loading,” Refract. Ind. Ceram., 54(6), 497 – 501 (2014).
ACKNOWLEDGMENT
The work was carried out with the financial support of the Ministry of Education and Science of the Russian Federation within the framework of the state task in the field of science, project No. 9.1372.2017/4.6.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Novye Ogneupory, No. 3, pp. 58 – 63, March 2019.
Rights and permissions
About this article
Cite this article
Kuzin, V.V., Grigor’ev, S.N. & Ermolin, V.N. Impulse Laser Effect on Graphitized Surface of Y–TZP-Ceramics. Refract Ind Ceram 60, 177–182 (2019). https://doi.org/10.1007/s11148-019-00332-y
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11148-019-00332-y