Skip to main content
Log in

Enhanced optical, morphological, dielectric, and conductivity properties of gold nanoparticles doped with PVA/CMC blend as an application in organoelectronic devices

  • Published:
Journal of Materials Science: Materials in Electronics Aims and scope Submit manuscript

Abstract

Stevia rebaudiana plant leaves were used for biosynthesis of gold nanoparticles (AuNPs). Transmission electron microscope images showed various shapes and sizes of AuNPs. Various amounts of AuNPs were added to polyvinyl alcohol/carboxymethylcellulose (PVA/CMC, 40/60) via the casting method. The X-ray diffraction (XRD) spectrum of pure blend shows the amorphous nature of the blend. FTIR spectra showed the interaction between PVA/CMC and AuNPs. The ultra-violet and visible spectra showed emerging new peak of surface plasmon resonance of AuNPs for the filled samples. The scanning electron microscope images showed bright spots on the sample’s surface, which was attributed to AuNPs. AC conductivity exhibited enhancement after the addition of gold nanoparticles. The ε′ and ε″ were reduced with increasing the frequency due to direction dipoles of applied electric field. Because of the mobile charges inside the polymeric backbone, higher values of ε′ and ε″ were observed at low frequencies. The tanδ showed increased with an increase in AuNPs concentration and decrease at high frequency, as expected.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Scheme 1
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12

Similar content being viewed by others

References

  1. C. Yang, S. Lin, Alkaline composite PEO–PVA–glass-fibre-mat polymer electrolyte for Zn–air battery. J. Power Sources 112, 497–503 (2002)

    Article  CAS  Google Scholar 

  2. R. Kandulna, R.B. Choudhary, Concentration-dependent behaviors of ZnO-reinforced PVA–ZnO nanocomposites as electron transport materials for OLED application. Polym. Bull. 75, 3089–3107 (2018). https://doi.org/10.1007/s00289-017-2186-9

    Article  CAS  Google Scholar 

  3. A.M. Hezma, A. Rajeh, M.A. Mannaa, An insight into the effect of zinc oxide nanoparticles on the structural, thermal, mechanical properties and antimicrobial activity of Cs/PVA composite. Colloids Surfaces A Physicochem. Eng. Asp. 581, 123821 (2019). https://doi.org/10.1016/J.COLSURFA.2019.123821

    Article  CAS  Google Scholar 

  4. A. Rajeh, A.M. Hezma, Spectroscopic and drug delivery studies of moxifloxacin loaded polylactic acid/polycaprolacton polymeric matrix for medical application. Res. J. Pharm. Biol. Chem. Sci. 8, 1163–1170 (2017)

    Google Scholar 

  5. S. Choudhary, P. Dhatarwal, R.J. Sengwa, Study on crystalline phases and degree of crystallinity of the melt compounded PVA/MMT and PVA/PVP/MMT nanocomposites. Indian J. Pure Appl. Phys. 59(2), 92–102 (2021)

    Google Scholar 

  6. X. Ma, P.R. Chang, J. Yu, Properties of biodegradable thermoplastic pea starch/carboxymethyl cellulose and pea starch/microcrystalline cellulose composites. Carbohydr. Polym. 72, 369–375 (2008). https://doi.org/10.1016/J.CARBPOL.2007.09.002

    Article  CAS  Google Scholar 

  7. P.K. Varshney, S. Gupta, Natural polymer-based electrolytes for electrochemical devices: a review. Ionics 17, 479–483 (2011)

    Article  CAS  Google Scholar 

  8. M.M. Abutalib, Insights into the structural, optical, thermal, dielectric, and electrical properties of PMMA/PANI loaded with graphene oxide nanoparticles. Phys. B Condens. Matter. 552, 19–29 (2019). https://doi.org/10.1016/J.PHYSB.2018.09.034

    Article  CAS  Google Scholar 

  9. L.H. Gaabour, Spectroscopic and thermal analysis of polyacrylamide/chitosan (PAM/CS) blend loaded by gold nanoparticles. Results Phys. 7, 2153–2158 (2017). https://doi.org/10.1016/J.RINP.2017.06.027

    Article  Google Scholar 

  10. A.M. Abdelghany, A.H. Oraby, M.O. Farea, Influence of green synthesized gold nanoparticles on the structural, optical, electrical and dielectric properties of (PVP/SA) blend. Phys. B Condens. Matter. 560, 162–173 (2019). https://doi.org/10.1016/J.PHYSB.2019.02.029

    Article  CAS  Google Scholar 

  11. H.M. Ragab, A. Rajeh, Structural, thermal, optical and conductive properties of PAM/PVA polymer composite doped with Ag nanoparticles for electrochemical application. J. Mater. Sci. Mater. Electron. 31, 16780–16792 (2020)

    Article  CAS  Google Scholar 

  12. E.M. Abdelrazek, I.S. Elashmawi, A.M. Hezma, A. Rajeh, M. Kamal, Effect of an encapsulate carbon nanotubes (CNTs) on structural and electrical properties of PU/PVC nanocomposites. Phys. B Condens. Matter. 502, 48–55 (2016). https://doi.org/10.1016/j.physb.2016.08.040

    Article  CAS  Google Scholar 

  13. A.M. Hezma, I.S. Elashmawi, A. Rajeh, M. Kamal, Change spectroscopic, thermal and mechanical studies of PU/PVC blends. Phys. B Condens. Matter. 495, 4–10 (2016)

    Article  CAS  Google Scholar 

  14. I.S. Elashmawi, E.M. Abdelrazek, A.M. Hezma, A. Rajeh, Modification and development of electrical and magnetic properties of PVA/PEO incorporated with MnCl2. Phys. B Condens. Matter. 434, 57–63 (2014). https://doi.org/10.1016/j.physb.2013.10.038

    Article  CAS  Google Scholar 

  15. E.M. Abdelrazek, I.S. Elashmawi, A.M. Hezma, A. Rajeh, The accessibility of change of the structural, morphological and thermal properties by intermolecular hydrogen bonding in PEO/PVA blend containing MnCl2. Int. J. Mod. App. Phys. 2, 83–96 (2012)

    Google Scholar 

  16. N.H. Ahmad, M.I.N. Isa, Characterization of un-plasticized and propylene carbonate plasticized carboxymethyl cellulose doped ammonium chloride solid biopolymer electrolytes. Carbohydr. Polym. 137, 426–432 (2016). https://doi.org/10.1016/J.CARBPOL.2015.10.092

    Article  CAS  Google Scholar 

  17. M.M. Abutalib, A. Rajeh, Structural, thermal, optical and conductivity studies of Co/ZnO nanoparticles doped CMC polymer for solid state battery applications. Polym. Testing 91, 106803 (2020)

    Article  CAS  Google Scholar 

  18. A.M. Abdelghany, A.H. Oraby, G.M. Asnag, Structural, thermal and electrical studies of polyethylene oxide/starch blend containing green synthesized gold nanoparticles. J. Mol. Struct. 1180, 15–25 (2019)

    Article  CAS  Google Scholar 

  19. A.A. Menazea, N.S. Awwad, H.A. Ibrahium, M.K. Ahmed, Casted polymeric blends of carboxymethyl cellulose/polyvinyl alcohol doped with gold nanoparticles via pulsed laser ablation technique; morphological features, optical and electrical investigation. Radiat. Phys. Chem. 177, 109155 (2020)

    Article  CAS  Google Scholar 

  20. M.A. Morsi et al., Nanosecond laser-irradiation assisted the improvement of structural, optical and thermal properties of polyvinyl pyrrolidone/carboxymethyl cellulose blend filled with gold nanoparticles. J. Mater. Sci. Mater. Electron. 30, 2693–2705 (2019)

    Article  CAS  Google Scholar 

  21. M.M. Abutalib, Effect of zinc oxide nanorods on the structural, thermal, dielectric and electrical properties of polyvinyl alcohol/carboxymethyle cellulose composites. Phys. B Condens. Matter. 557, 108–116 (2019). https://doi.org/10.1016/J.PHYSB.2019.01.018

    Article  CAS  Google Scholar 

  22. S. Al-Thabaiti, M. Malik, A. Al-Youbi, Z. Khan, J. Hussain, Effects of surfactant and polymer on the morphology of advanced nanomaterials in aqueous solution. Int. J. Electrochem. Sci. 8, 204–218 (2013)

    CAS  Google Scholar 

  23. A. Rajeh, M.A. Morsi, I.S. Elashmawi, Enhancement of spectroscopic, thermal, electrical and morphological properties of polyethylene oxide/carboxymethyl cellulose blends: combined FT-IR/DFT. Vacuum 159, 430–440 (2019)

    Article  CAS  Google Scholar 

  24. M.A. Morsi et al., Effect of lithium titanate nanoparticles on the structural, optical, thermal and electrical properties of polyethylene oxide/carboxymethyl cellulose blend. J. Mater. Sci. Mater. Electron. 29(18), 15912–15925 (2018)

    Article  CAS  Google Scholar 

  25. M.A. Morsi, M. Abdelaziz, A.H. Oraby, I. Mokhles, Structural, optical, thermal, and dielectric properties of polyethylene oxide/carboxymethyl cellulose blend filled with barium titanate. J. Phys. Chem. Solids 125, 103–114 (2019)

    Article  CAS  Google Scholar 

  26. C. Basavaraja, J.K. Kim, Characterization and temperature-dependent conductivity of polyaniline nanocomposites encapsulating gold nanoparticles on the surface of carboxymethyl cellulose. Mater. Sci. Eng. B 178(2), 167–173 (2013)

    Article  CAS  Google Scholar 

  27. M.A. Morsi, S.A. El-Khodary, A. Rajeh, Enhancement of the optical, thermal and electrical properties of PEO/PAM: Li polymer electrolyte films doped with Ag nanoparticles. Phys. B Condens. Matter. 539, 88–96 (2018)

    Article  CAS  Google Scholar 

  28. A. Hebeish, M. Hashem, M.A. El-Hady, S. Sharaf, Development of CMC hydrogels loaded with silver nano-particles for medical applications. Carbohydr. Polymers 92, 407–413 (2013)

    Article  CAS  Google Scholar 

  29. I. Jahit, N. Nazmi, M. Isa, N. Sarbon, Preparation and physical properties of gelatin/CMC/chitosan composite films as affected by drying temperature. Int. Food Res. J. 3, 1068–1074 (2016)

    Google Scholar 

  30. M.M. Abutalib, A. Rajeh, Influence of MWCNTs/Li-doped TiO2 nanoparticles on the structural, thermal, electrical and mechanical properties of poly (ethylene oxide)/poly (methylmethacrylate) composite. J. Organomet. Chem. 918, 121309 (2020). https://doi.org/10.1016/J.JORGANCHEM.2020.121309

    Article  CAS  Google Scholar 

  31. A. El-Aziz, A. Ramadan, M.R. Al-Othman, M.A. Mahmoud, Degradation of DDT by gold nanoparticles synthesised using Lawsonia inermis for environmental safety. Biotechnol. Biotechnol. Equip. 32(5), 1174–1182 (2018)

    Article  CAS  Google Scholar 

  32. M.M. Abdelrazek et al., Structural, optical, morphological and thermal properties of PEO/PVP blend containing different concentrations of biosynthesized Au nanoparticles. J. Mater. Res. Technol. 7, 419–431 (2018)

    Article  CAS  Google Scholar 

  33. A.M. Abdelghany, E.M. Abdelrazek, S.I. Badr, M.A. Morsi, Effect of gamma-irradiation on (PEO/PVP)/Au nanocomposite: materials for electrochemical and optical applications. Mater. Des. 97, 532–543 (2016). https://doi.org/10.1016/j.matdes.2016.02.082

    Article  CAS  Google Scholar 

  34. G. Patel, M. Sureshkumar, P. Patel, Spectroscopic investigation and characterizations of PAM/PEO blends films. Soft Sci. Res. Publ. 4, 9–24 (2015)

    Google Scholar 

  35. A.M. Hezma et al., Enhancement of the thermal and mechanical properties of polyurethane/polyvinyl chloride blend by loading single walled carbon nanotubes. Progress Natl. Sci. Mater. Int. 27, 338–343 (2017)

    Article  CAS  Google Scholar 

  36. N. Haleem et al., Synthesis of carboxymethyl cellulose from waste of cotton ginning industry. Carbohyd. Polym. 113, 249–255 (2014)

    Article  CAS  Google Scholar 

  37. M.O. Farea, A.M. Abdelghany, M.S. Meikhail, A.H. Oraby, Effect of cesium bromide on the structural, optical, thermal and electrical properties of polyvinyl alcohol and polyethylene oxide. J. Mater. Res. Technol. 9, 1530–1538 (2020)

    Article  CAS  Google Scholar 

  38. M.M. Abutalib, A. Rajeh, Preparation and characterization of polyaniline/sodium alginate-doped TiO2 nanoparticles with promising mechanical and electrical properties and antimicrobial activity for food packaging applications. J. Mater. Sci. Mater. Electron. 31, 1–13 (2020). https://doi.org/10.1007/s10854-020-03483-8

    Article  CAS  Google Scholar 

  39. M.M. Abutalib, A. Rajeh, Influence of Fe3O4 nanoparticles on the optical, magnetic and electrical properties of PMMA/PEO composites: combined FT-IR/DFT for electrochemical applications. J. Organomet. Chem. 920, 121348 (2020). https://doi.org/10.1016/J.JORGANCHEM.2020.121348

    Article  CAS  Google Scholar 

  40. M.M. Abutalib, A. Rajeh, Influence of ZnO/Ag nanoparticles doping on the structural, thermal, optical and electrical properties of PAM/PEO composite. Phys. B 578, 411796 (2020)

    Article  CAS  Google Scholar 

  41. M.A. Morsi, A. Rajeh, A.A. Al-Muntaser, Reinforcement of the optical, thermal and electrical properties of PEO based on MWCNTs/Au hybrid fillers: nanodielectric materials for organoelectronic devices. Compos. Part B Eng. 73, 106957 (2019)

    Article  Google Scholar 

  42. A. Rajeh, H.M. Ragab, M.M. Abutalib, Co doped ZnO reinforced PEMA/PMMA composite: structural, thermal, dielectric and electrical properties for electrochemical applications. J. Mol. Struct. (2020). https://doi.org/10.1016/j.molstruc.2020.128447

    Article  Google Scholar 

  43. M.A. Morsi et al., Nd: YAG nanosecond laser induced growth of Au nanoparticles within CMC/PVA matrix: multifunctional nanocomposites with tunable optical and electrical properties. Compos. Commun. 24, 100662 (2021)

    Article  Google Scholar 

  44. E.M. Abdelrazek, I.S. Elashmawi, H.M. Ragab, Manifestation of MnCl2 fillers incorporated into the polymer matrices in their dielectric properties. Phys. B 403, 3097–3104 (2008)

    Article  CAS  Google Scholar 

  45. P. Dhatarwal, S. Choudhary, R.J. Sengwa, Electrochemical performance of Li+-ion conducting solid polymer electrolytes based on PEO–PMMA blend matrix incorporated with various inorganic nanoparticles for the lithium ion batteries. Compos. Commun. 10, 11–17 (2018)

    Article  Google Scholar 

  46. H. Peng, G. Ma, W. Ying, A. Wang, H. Huang, Z. Lei, In situ synthesis of polyaniline/sodium carboxymethyl cellulose nanorods for high-performance redox supercapacitors. J. Power Sources 211, 40–45 (2012)

    Article  CAS  Google Scholar 

  47. Q.A. Alsulami, Structural, dielectric, and magnetic studies based on MWCNTs/NiFe2O4/ZnO nanoparticles dispersed in polymer PVA/PEO for electromagnetic applications. J. Mater. Sci. Mater. Electron. 32, 2906–2924 (2021)

    Article  CAS  Google Scholar 

  48. M.M. Abutalib, A. Rajeh, Enhanced structural, electrical, mechanical properties and antibacterial activity of Cs/PEO doped mixed nanoparticles (Ag/TiO2) for food packaging applications. Polym. Testing 93, 107013 (2020)

    Article  Google Scholar 

  49. K.N. Kumar, M. Kang, K. Sivaiah, M. Ravi, Y.C. Ratnakaram, Enhanced electrical properties of polyethylene oxide (PEO) + polyvinylpyrrolidone (PVP): Li+ blended polymer electrolyte films with addition of Ag nanofiller. Ionics 22, 815–825 (2016). https://doi.org/10.1007/s11581-015-1599-4

    Article  CAS  Google Scholar 

  50. O. Pravakar, T. Siddaiah, P.V.R.K. Ramacharyulu, N.O. Gopal, C. Ramu, H. Nagabhushana, Spectroscopic, thermal, structural and electrical studies on VO2+ ions doped PVA/MAA: EA polymer blend films. J. Sci. Adv. Mater. Dev. 4, 267–275 (2019). https://doi.org/10.1016/J.JSAMD.2019.03.004

    Article  Google Scholar 

  51. G.M. Asnag, A.H. Oraby, A.M. Abdelghany, Green synthesis of gold nanoparticles and its effect on the optical, thermal and electrical properties of carboxymethyl cellulose. Compos. Part B Eng. 172, 436–446 (2019). https://doi.org/10.1016/J.COMPOSITESB.2019.05.044

    Article  CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to A. Rajeh.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Atta, M.R., Alsulami, Q.A., Asnag, G.M. et al. Enhanced optical, morphological, dielectric, and conductivity properties of gold nanoparticles doped with PVA/CMC blend as an application in organoelectronic devices. J Mater Sci: Mater Electron 32, 10443–10457 (2021). https://doi.org/10.1007/s10854-021-05701-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10854-021-05701-3

Navigation