Abstract
The martensitic transformation in a Fe–C–Mn–Si bainitic steel was examined by in situ high-temperature laser scanning confocal microscopy (LSCM) and dilatometry. The phenomenon of continuous martensitic transformation during austempering was firstly dynamically observed by LSCM. Differing from the commonly accepted viewpoint on martensite formation in bainitic steels, the martensitic transformation in the conventional medium-carbon bainitic steel was not instantaneous and proceeded gradually when the sample was austempered below martensite starting temperature (MS). It can be attributed to the generation of internal stresses, thermal activation, stimulating nucleation, and the segregation of Mn. In addition, apart from the continuous martensitic transformation, the bainitic transformation was also directly observed by LSCM during austempering below MS. Moreover, it was clear from the results of dilatation during austempering that the inflection point in the dilatation curve against time was not the demarcation point between martensitic and bainitic transformation, and in situ observations confirmed that martensite was still formed after the inflection point. Therefore, the obtained results could be an excellent reference to further understand the mechanism of bainitic and martensitic transformations in Fe–C–Mn–Si bainitic steel during austempering below MS.
Graphic Abstract
Graphical abstract presents a series of frames that reveals the rapid growth of some black units during austempering at 240 °C, and these rapidly growing units (marked by arrows) were not present in the previous frame of the video. These black growing units (martensite laths) shown in Graphical abstract appeared over a time interval of ~ 420 s from 837.39 to 1257.37 s during austempering. This phenomenon differs from the previously held viewpoint where martensitic transformation is expected to be finished in a very short period of time after a sample is cooled to a certain temperature below MS because of the diffusionless nature of martensite transformation in conventional medium-carbon bainitic steels. The growth of martensite laths during the austempering process at 240 °C.
Similar content being viewed by others
References
A. Bag, K.K. Ray, E.S. Dwarakadasa, Metall. Mater. Trans. A 30, 1193 (1999)
A. Kumar, S.B. Singh, K.K. Ray, Mater. Sci. Eng. A 474, 270 (2008)
J.W. Zhao, Z.Y. Jiang, Prog. Mater Sci. 94, 174 (2018)
J.Y. Tian, G. Xu, Z.Y. Jiang, H.J. Hu, M.X. Zhou, Met. Mater. Int. 24, 1202 (2018)
D.M. Xu, G.Q. Li, X.L. Wan, R.L. Xiong, G. Xu, K.M. Wu, M.C. Somani, R.D.K. Misra, Mater. Sci. Eng. A 688, 407 (2017)
G. Xu, F. Liu, L. Wang, H.J. Hu, Scr. Mater. 68, 833 (2013)
H.J. Hu, G. Xu, L. Wang, Z.L. Xue, Y.L. Zhang, G.H. Liu, Mater. Des. 84, 95 (2015)
Y. Tomita, K. Morioka, Mater. Charact. 38, 243 (1997)
G.B. Olson, M. Cohen, Metall. Trans. A 7, 1915 (1976)
T.S. Wang, M. Zhang, Y.H. Wang, J. Yang, F.C. Zhang, Scr. Mater. 68, 162 (2013)
L.L. Ban, J. Wen, X.X. Shi, W.P. Liu, Metall. Anal. 31, 1 (2011)
Z.C. Liu, Y.P. Ji, Z.P. Hei, H.P. Ren, Trans. Mater. Heat. Treat. 35, 96 (2014)
X. Yu, S.S. Babu, J.C. Lippold, H. Terasaki, Y.I. Komizo, Metall. Mater. Trans. A 43, 1538 (2012)
I.A. Yakubtsov, G.R. Purdy, Metall. Mater. Trans. A 43, 437 (2012)
S. Samanta, P. Biswas, S. Giri, S.B. Singh, S. Kundu, Acta Mater. 105, 390 (2016)
L. Zhao, L. Qian, J. Meng, Q. Zhou, F.C. Zhang, Scr. Mater. 112, 96 (2016)
H. Okamoto, M. Oka, Metall. Trans. A 16, 2257 (1985)
A. Borgenstam, M. Hillert, Acta Mater. 45, 651 (1997)
G. Ghosh, Philos. Mag. A 71, 333 (2016)
H. Pal, A. Chanda, M. De, J. Alloys Compd. 278, 209 (1998)
T. Ko, S.A. Cottrell, J. Iron Steel Inst. 172, 307 (1952)
Y.Z. Zhu, J.P. Xu, Int. J. Min. Met. Mater. 19, 821 (2012)
Z.Y. Xu, Martensite Transformation and Martensite (Science Press, Beijing, 1980). (In Chinese)
Y. Tomota, Y.X. Wang, T. Ohmura, N. Sekido, S. Harjo, T. Kawasaki, W. Gong, A. Taniyama, ISIJ Int. 58, 2125 (2018)
Z.W. Hu, G. Xu, H.J. Hu, L. Wang, Z.L. Xue, Int. J. Min. Met. Mater. 21, 371 (2013)
T. Hanamura, S. Torizuka, S. Tamura, S. Enokida, H. Takech, Mater. Sci. Forum 783–786, 1027 (2014)
S.J. Lee, C.J.V. Tyne, Metal. Mater. Trans. A 43, 422 (2012)
F. Hajyakbary, J. Sietsma, R.H. Petrov, G. Miyamoto, T. Furuhara, M.J. Santofimia, Scr. Mater. 137, 27 (2017)
E.P.D. Silva, D.D. Knijf, W. Xu, C. Föjer, Y. Houbaert, J. Sietsma, Mater. Sci. Technol. 31, 808 (2015)
J.Y. Tian, G. Xu, M.X. Zhou, H.J. Hu, Steel Res. Int. (2018). https://doi.org/10.1002/srin.201700469
M. Oka, H. Okamoto, Metall. Trans. A 19, 447 (1988)
Acknowledgements
This work is supported by National Natural Science Foundation of China [Nos. 51874216 & 51704217]; Major Projects of Technological Innovation in Hubei [No.2017AAA116]; Hebei Joint Research Fund for Iron and Steel [E2018318013]; and the State Scholarship Fund of China Scholarship Council.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Tian, J., Xu, G., Jiang, Z. et al. In-Situ Observation of Martensitic Transformation in a Fe–C–Mn–Si Bainitic Steel During Austempering. Met. Mater. Int. 26, 961–972 (2020). https://doi.org/10.1007/s12540-019-00370-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12540-019-00370-8