Abstract
Based on the unified strength criterion, the plane strain elastic–plastic bending of a linear strain hardening curved beam is analyzed in this study. The solutions for the properties of plane strain bending of the curved beam are obtained, taking into account the strength difference effect and the intermediate principal stress effect. Those solutions based on different strength criteria, such as Tresca, von Mises, Mohr–Coulomb, TS and GTS, are the special cases (Tresca, Mohr–Coulomb, TS and GTS) or linear approximation (von Mises) of the present solutions. Besides, a series of solutions that can take account of the strength difference effect and the differing effect of intermediate principal stress can be obtained from it. Consequently, the present solutions are suitable for various kinds of engineering materials. The influences of strength difference and intermediate principal stress on the two critical bending moments, the two interface radii between the elastic and plastic regions, and the radial displacements and stresses of points at the symmetrical plane of the curved beam are discussed comprehensively. It can be concluded from the analyses that the strength difference effect and the intermediate principal stress effect on the properties of plane strain bending of the curved beam are considerable and cannot be ignored.
Similar content being viewed by others
References
Arefi, M.: Elastic solution of a curved beam made of functionally graded materials with different cross sections. Steel Compos. Struct. 18, 659–672 (2015)
Arici, M., Granata, M.F.: Generalized curved beam on elastic foundation solved by transfer matrix method. Struct. Eng. Mech. 40, 279–295 (2011)
Matsuo, T., Goto, T., Takahashi, J.: Investigation about the fracture behavior and strength in a curved section of CF/PP composite by a thin-curved beam specimen. Adv. Compos. Mater. 24, 249–268 (2015)
Rajasekaran, S.: Analysis of curved beams using a new differential transformation based curved beam element. Meccanica 49, 863–886 (2014)
Timoshenko, S.P., Goodier, J.N.: Theory of Elasticity. McGraw-Hill, New York (1970)
Shaffer, B.W., House Jr., R.N.: The significance of zero shear stress in the pure bending of a wide curved bar. J. Aeronaut. Sci. 24, 307–308 (1957)
Shaffer, B.W., House Jr., R.N.: Displacements in a wide curved bar subjected to pure elasto-plastic bending. J. Appl. Mech. Trans. ASME 24, 447–452 (1957)
Hill, R.: The Mathematical Theory of Plasticity. Oxford University Press, London (1967)
Dadras, P., Majlessi, S.A.: Plastic bending of working hardening materials. J. Eng. Ind. Trans. ASME 104, 224–230 (1982)
Dadras, P.: Plane strain elasto-plastic bending of a strain hardening curved beam. Int. J. Mech. Sci. 43, 39–56 (2001)
Eraslan, A.N., Arslan, E.: A concise analytical treatment of elasto-plastic bending of a strain hardening curved beam. Z. Angew. Math. Mech. 88, 600–616 (2008)
Eraslan, A.N., Arslan, E.: Analytical solution to the bending of a nonlinearly hardening wide curved bar. Acta Mech. 210, 71–84 (2010)
Eraslan, A.N., Arslan, E.: A computational study on the nonlinear hardening curved beam problem. Int. J. Pure Appl. Math. 43, 129–143 (2008)
Nie, G.J., Zhong, Z.: Closed-form solutions for elastoplastic pure bending of a curved beam with material inhomogeneity. Acta Mech. Solida Sinica 27, 54–64 (2014)
Yu, M.H., He, L.N.: A new model and theory on yield and failure of materials under complex stress state. Mech. Behav. Mater. 3, 841–846 (1991)
Fan, S.C., Yu, M.H., Yang, S.Y.: On the unification of yield criteria. J. Appl. Mech. Trans. ASME 68, 341–343 (2001)
Yu, M.H.: Advance in strength theory of material and complex stress state in the 20th century. Appl. Mech. Rev. 55, 169–218 (2002)
Yu, M.H., Li, J.C., Zhang, Y.Q.: Unified characteristics line theory of spatial axisymmetric plastic problem. Sci. China Ser. E: Technol. Sci. 44, 207–215 (2001)
Zhang, Y.Q., Hao, H., Yu, M.H.: A unified characteristic theory for plastic plane stress and strain problems. J. Appl. Mech. Trans. ASME 70, 649–654 (2003)
Xu, S.Q., Yu, M.H.: The effect of the intermediate principal stress on the ground response of circular openings in rock mass. Rock Mech. Rock Eng. 39, 169–181 (2006)
Li, J.C., Ma, G.W., Yu, M.H.: Penetration analysis for geo-material based on unified strength criterion. Int. J. Impact Eng. 35, 1154–1163 (2008)
Jin, C.W., Wang, L.Z., Zhang, Y.Q.: Strength differential effect and influence of strength criterion on burst pressure of thin-walled pipelines. Int. J. Mech. Sci. 53, 348–354 (2011)
Kolupaev, V.A., Yu, M.H., Altenbach, H.: Visualization of the unified strength theory. Arch. Appl. Mech. 83, 1061–1085 (2013)
Yu, M.H.: Twin shear stress yield criterion. Int. J. Mech. Sci. 25, 71–74 (1983)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, H., Pang, M. & Zhang, Y. Effects of strength difference and intermediate principal stress on plane strain elastic–plastic bending of a curved beam. Acta Mech 227, 3351–3366 (2016). https://doi.org/10.1007/s00707-016-1681-7
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00707-016-1681-7