Abstract
Carbon black (CB) is usually used to reinforce rubbers such as styrene-butadiene rubber (SBR). CB has sustainability and human health issues owing to its energy-intensive production process. Focusing on developing sustainable alternatives, bi-modal distributed cellulose fibers (CF) were used to partially replace CB. Cellulose fibers were pre-dispersed and surface modified and mixed with SBR matrices using internal and open rubber mill mixers. The properties of the prepared samples were measured and compared with CB/SBR counterparts. This study highlights the combined effects of CF bi-modality, surface modification, and pre-dispersion on dispersion quality, viscoelastic, curing, and mechanical properties. Our results showed that surface modification of bi-modal CFs and their pre-dispersion promoted dispersion by 15% and 12%, respectively. In comparison with CB as a common additive in SBR composites, the SBR samples filled with pre-dispersed modified bi-modal CF resulted in better dispersion, up to a 24% increase in tensile strength, a 50% improvement of modulus, and a 27% rise in tear strength. Given the sustainability feature of CFs, our results confirmed that the combined effects of pre-dispersed modified bi-modal CFs could be an industrially viable, cost-effective alternative to partially replace CB in SBR composites where the gains in strength are obtained by NFCs, and micro-fibrillated fibers are used to replace the additional NFCs for unrequired excessive strength.
Similar content being viewed by others
References
Akindoyo JO, Beg MDH, Ghazali S, Heim HP, Feldmann M (2017) Effects of surface modification on dispersion, mechanical, thermal and dynamic mechanical properties of injection molded PLA-hydroxyapatite composites. Compos Part A Appl Sci Manuf 103:96–105. https://doi.org/10.1016/J.COMPOSITESA.2017.09.013
Akinyemi BA, Adesina A (2021) Utilization of polymer chemical admixtures for surface treatment and modification of cellulose fibres in cement-based composites: a review. Cellulose 28:1241–1266. https://doi.org/10.1007/s10570-020-03627-3
Alshahrani H, Arun Prakash VR (2022) Mechanical, fatigue and DMA behaviour of high content cellulosic corn husk fibre and orange peel biochar epoxy biocomposite: a greener material for cleaner production. J Clean Prod 374:133931. https://doi.org/10.1016/J.JCLEPRO.2022.133931
Bai W, Li K (2009) Partial replacement of silica with microcrystalline cellulose in rubber composites. Compos Part A Appl Sci Manuf 40:1597–1605. https://doi.org/10.1016/j.compositesa.2009.07.006
Bhattacharyya SK, Chakraborty A, Ghosh S, Dasgupta S, Mukhopadhyay R, Bandyopadhyay A (2013) Microcrystalline cellulose (MCC) as green multifunctional additive (MFA) in emulsion styrene butadiene rubber based high silica compound. Plast Rubber Compos 42:393–400. https://doi.org/10.1179/1743289813Y.0000000061
Bondeson D, Syre P, Niska KO (2008) All cellulose nanocomposites produced by extrusion. J Biobased Mater Bioenergy 1:367–371. https://doi.org/10.1166/jbmb.2007.011
Célino A, Gonç Alves BO, Jacquemin F, Fréour S (2014) Qualitative and quantitative assessment of water sorption in natural fibres using ATR-FTIR spectroscopy. Carbohydr Polym 101:163–170. https://doi.org/10.1016/j.carbpol.2013.09.023
Choi SS, Park BH, Song H (2004) Influence of filler type and content on properties of styrene-butadiene rubber (SBR) compound reinforced with carbon black or silica. Polym Adv Technol 15:122–127. https://doi.org/10.1002/PAT.421
Chu Y, Sun Y, Wu W, Xiao H (2020) Dispersion properties of nanocellulose: a review. Carbohydr Polym 250:116892. https://doi.org/10.1016/j.carbpol.2020.116892
Correia CA, Valera TS (2019) Cellulose nanocrystals and jute fiber-reinforced natural rubber composites: cure characteristics and mechanical properties. Mater Res. https://doi.org/10.1590/1980-5373-MR-2019-0192
Dey A, Eagle INR, Yodo N (2021) A review on filament materials for fused filament fabrication. J Manuf Mater Process 5:69. https://doi.org/10.3390/jmmp5030069
El Achaby M, El Miri N, Aboulkas A, Zahouily M, Bilal E, Barakat A, Solhy A (2017) Processing and properties of eco-friendly bio-nanocomposite films filled with cellulose nanocrystals from sugarcane bagasse. Int J Biol Macromol 96:340–352. https://doi.org/10.1016/j.ijbiomac.2016.12.040
Fan Y, Fowler GD, Zhao M (2020) The past, present and future of carbon black as a rubber reinforcing filler: a review. J Clean Prod 247:119115. https://doi.org/10.1016/j.jclepro.2019.119115
Gholami F, Pakzad L, Behzadfar E (2020) Morphological, interfacial and rheological properties in multilayer polymers: a review. Polymer (guildf) 208:122950. https://doi.org/10.1016/j.polymer.2020.122950
Hamad WY, Miao C, Beck S (2019) Growing the bioeconomy: advances in the development of applications for cellulose filaments and nanocrystals. Ind Biotechnol 15:133–137. https://doi.org/10.1089/ind.2019.29172.qyh
Herrera N, Mathew AP, Oksman K (2015) Plasticized polylactic acid/cellulose nanocomposites prepared using melt-extrusion and liquid feeding: mechanical, thermal and optical properties. Compos Sci Technol 106:149–155. https://doi.org/10.1016/j.compscitech.2014.11.012
Higginson JL, Rezaei Kolahchi A, Behzadfar E (2022) Evaluation of layer adhesion and uniformity in poly(lactic acid) and thermoplastic starch multilayered films. Ind Eng Chem Res 61:7996–8004. https://doi.org/10.1021/acs.iecr.2c00898
Karamikamkar S, Abidli A, Behzadfar E, Rezaei S, Naguib H, Park CB (2019) The effect of graphene-nanoplatelets on gelation and structural integrity of a polyvinyltrimethoxysilane-based aerogel†. Doi:https://doi.org/10.1039/c9ra00994a
Katsuhara S, Takagi Y, Sunagawa N, Igarashi K, Yamamoto T, Tajima K, Isono T, Satoh T (2021) Enhanced self-assembly and mechanical properties of cellulose-based triblock copolymers: comparisons with amylose-based triblock copolymers. ACS Sustain Chem Eng 9:9779–9788. https://doi.org/10.1021/acssuschemeng.1c02180
Khan MN, Lacroix M, Wessels C, Van Dael M (2022) Converting wastewater cellulose to valuable products: a techno-economic assessment. J Clean Prod 365:132812. https://doi.org/10.1016/J.JCLEPRO.2022.132812
Ku H, Wang H, Pattarachaiyakoop N, Trada M (2011) A review on the tensile properties of natural fiber reinforced polymer composites. Compos Part B Eng 42:856–873. https://doi.org/10.1016/J.COMPOSITESB.2011.01.010
Laine J, Lindström T, Bremberg C, Glad-Nordmark G (2003) Studies on topochemical modification of cellulosic fibres. Part 4. Toposelectivity of carboxymethylation and its effects on the swelling of fibres. Nord Pulp Pap Res J. https://doi.org/10.3183/npprj-2003-18-03-p316-324
Leblanc JL (2002) Rubber–filler interactions and rheological properties in filled compounds. Prog Polym Sci 27:627–687. https://doi.org/10.1016/S0079-6700(01)00040-5
Li C, Huang F, Wang J, Liang X, Huang S, Gu J (2018) Effects of partial replacement of carbon black with nanocrystalline cellulose on properties of natural rubber nanocomposites. J Polym Eng 38:137–146. https://doi.org/10.1515/polyeng-2016-0382
Liu W, Zhang S, Liu K, Yang H, Lin Q, Xu T, Song X, Du H, Bai L, Yao S, Si C (2023) Sustainable preparation of lignocellulosic nanofibrils and cellulose nanopaper from poplar sawdust. J Clean Prod 384:135582. https://doi.org/10.1016/J.JCLEPRO.2022.135582
Lo Re G, Spinella S, Boujemaoui A, Vilaseca F, Larsson PT, Adås F, Berglund LA (2018) Poly(ε-caprolactone) biocomposites based on acetylated cellulose fibers and wet compounding for improved mechanical performance. ACS Sustain Chem Eng 6:6753–6760. https://doi.org/10.1021/acssuschemeng.8b00551
Lubis H, Sharman E, Chairina E, Siregar I, Rizky M, Maiya D, Machdhalie T (2020) Fabrication and characterization of adding coconut shell actived nanocarbon to lightweight concrete. J Phys Conf Ser 1428:012039. https://doi.org/10.1088/1742-6596/1428/1/012039
Matthews C, Moran F, Jaiswal AK (2021) A review on European Union’s strategy for plastics in a circular economy and its impact on food safety. J Clean Prod. https://doi.org/10.1016/J.JCLEPRO.2020.125263
Mollaabbasi R, Behzadfar E, Taghavi SM (2019) A simplified semi-analytical model for the filling and cooling process in plastic molding. Phys Fluids 31:63105. https://doi.org/10.1063/1.5100257
Moonart U, Utara S (2019) Effect of surface treatments and filler loading on the properties of hemp fiber/natural rubber composites. Cellulose 26:7271–7295. https://doi.org/10.1007/s10570-019-02611-w
Murai J, Nakajima T, Matsuda T, Tsunoda K, Nonoyama T, Kurokawa T, Gong JP (2019) Tough double network elastomers reinforced by the amorphous cellulose network. Polymer 178:121686. https://doi.org/10.1016/J.POLYMER.2019.121686
Ohser J, Lacayo-Pineda J, Putman M, Rack A, Dobrovolskij D (2019) Estimation of filler macro-dispersion in rubber matrix by radiometric stereo microscopy. J Microsc 274:32–44. https://doi.org/10.1111/JMI.12782
Song K, Wu F, Tong TP, Wang XJ (2012) A real-time Mooney-viscosity prediction model of the mixed rubber based on the Independent Component Regression-Gaussian Process algorithm. J Chemom 26:557–564. https://doi.org/10.1002/CEM.2478
Sui G, Zhong WH, Yang XP, Yu YH, Zhao SH (2008) Preparation and properties of natural rubber composites reinforced with pretreated carbon nanotubes. Polym Adv Technol. https://doi.org/10.1002/pat.1163
Takayama T, Todo M, Takano A (2009) The effect of bimodal distribution on the mechanical properties of hydroxyapatite particle filled poly(L-lactide) composites. J Mech Behav Biomed Mater 2:105–112. https://doi.org/10.1016/j.jmbbm.2008.06.001
Tan X, Zhao Y, Shang M, Hamed GR, Jia L (2017) Supramolecular reinforcement of styrene-butadiene rubber composites. Polymer (guildf) 122:242–248. https://doi.org/10.1016/J.POLYMER.2017.06.056
Wang MJ (1998) Effect of polymer-filler and filler-filler interactions on dynamic properties of filled vulcanizates. Rubber Chem Technol 71:520–589. https://doi.org/10.5254/1.3538492
Xie H, Du H, Yang X, Si C (2018) Recent strategies in preparation of cellulose nanocrystals and cellulose nanofibrils derived from raw cellulose materials. Int J Polym Sci 2018:7923068. https://doi.org/10.1155/2018/7923068
Yu H-Y, Yan C-F (2017) Mechanical properties of cellulose nanofibril (CNF)- and cellulose nanocrystal (CNC)-based nanocomposites. Handb Nanocellulose Cellul Nanocomposites. https://doi.org/10.1002/9783527689972.ch12
Acknowledgments
This work was performed, in part, at Lakehead University and Toronto Metropolitan University. Parts of the experiments were conducted in the R&D Facility, AirBoss of America, located in Kitchener, Ontario, Canada.
Funding
The authors acknowledge the support by MITACS and the industrial partnership for research with Performance BioFilaments Inc. Materials were provided by Performance BioFilaments Inc. and AirBoss of America. The authors also acknowledge the support from Natural Sciences and Engineering Research Council of Canada (NSERC), Lakehead University, Toronto Metropolitan University, Ontario Research Fund (ORF) and Canada Foundation for Innovation (CFI) programs for supporting this research.
Author information
Authors and Affiliations
Contributions
VTL: Conceptualization, Methodology, Investigation, Data curation, Writing, Visualization. GM: Conceptualization, Methodology, Investigation. GF: Conceptualization, Methodology, Investigation. EB: Conceptualization, Investigation, Supervision, Writing, Review.
Corresponding author
Ethics declarations
Conflict of interest
The authors have no known competing financial interests that could have appeared to influence the work reported in this paper. Heim, Hans P. Feldmann, Maik.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Lashkar, V.T., Minhas, G., Fisher, G. et al. Production of greener styrene-butadiene rubber (SBR) composites through partial substitution of carbon black with bi-modal cellulose fibers. Cellulose 30, 9485–9499 (2023). https://doi.org/10.1007/s10570-023-05463-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10570-023-05463-7