1. Polymers for additive manufacturing: Collected contributions for MRS Communications

   • Jamie M. Messman
   • Daniel E. Bowen

   Introduction 22 June 2021 Pages: 87 - 87

2. New “all-in-one” silicone pastes for additive manufacturing of elastomer parts

   • James Beach
   • Steven Patterson
   • Petar R. Dvornic

   Polymers for Additive Manufacturing Research Letter 09 February 2021 Pages: 88 - 93

   

3. Compression sensors constructed from ferromagnetic particles embedded within soft materials

   • Justin K. Ruffalo
   • Jonathan D. Miller
   • Cory J. Berkland

   Polymers for Additive Manufacturing Research Letter 05 February 2021 Pages: 94 - 99

   

4. Mechanical and thermal properties of 3D-printed epoxy composites reinforced with boron nitride nanobarbs

   • Brett G. Compton
   • Jackson K. Wilt
   • Jason Taylor

   Polymers for Additive Manufacturing Research Letter 19 January 2021 Pages: 100 - 105

   

5. Direct ink writing techniques for in situ gelation and solidification

   • Jackson K. Wilt
   • Dustin Gilmer
   • Tomonori Saito

   Polymers for Additive Manufacturing Prospective 24 February 2021 Pages: 106 - 121

   

6. Enhancing nanomaterial dispersion and performance of parts printed via FFF by a solution casting method

   • William K. Ledford
   • Sina Sabury
   • S. Michael Kilbey II

   Polymers for Additive Manufacturing Research Letter 19 January 2021 Pages: 122 - 128

   

7. Novel polymer materials systems to expand the capabilities of FDM™-type additive manufacturing

   • Truman J. Word
   • Ariana Guerrero
   • D. A. Roberson

   Polymers for Additive Manufacturing Prospective 02 February 2021 Pages: 129 - 145

   

8. Supramolecular tools for polymer additive manufacturing

   • Danielle R. Berry
   • Karen P. Cortés-Guzmán
   • Ronald A. Smaldone

   Polymers for Additive Manufacturing Prospective 19 April 2021 Pages: 146 - 156

   

9. Comparing polarized Raman spectroscopy and birefringence as probes of molecular scale alignment in 3D printed thermoplastics

   • Nora M. Hassan
   • Kalman B. Migler
   • Jonathan E. Seppala

   Polymers for Additive Manufacturing Prospective 09 April 2021 Pages: 157 - 167

   

10. Structural response of 3D-printed rubber lattice structures under compressive fatigue

    • Mohammad I. Hatamleh
    • Carlos A. Barrios
    • Walter Voit

    Polymers for Additive Manufacturing Prospective 17 February 2021 Pages: 168 - 172

    

11. Selective laser sintering (SLS)-printable thermosetting resins via controlled conversion

    • C. Garrett Campbell
    • Dominik Jordon Astorga
    • Mathew Celina

    Polymers for Additive Manufacturing Research Letter 03 February 2021 Pages: 173 - 178

    

12. Process-structure–property relationships following thermo-oxidative exposure of powder bed fusion printed poly(phenylene sulfide)

    • Camden A. Chatham
    • Timothy E. Long
    • Christopher B. Williams

    Polymers for Additive Manufacturing Research Letter 25 March 2021 Pages: 179 - 188

    

13. Effect of micron-scale manufacturing flaws on the tensile response of centimeter sized two-photon polymerization microlattices

    • Jean-Baptiste Forien
    • James S. Oakdale
    • Juergen Biener

    Polymers for Additive Manufacturing Research Letter 15 April 2021 Pages: 189 - 196

    

14. 3D printing of biomedically relevant polymer materials and biocompatibility

    • Joseph Rey H. Sta. Agueda
    • Qiyi Chen
    • Rigoberto C. Advincula

    Polymers for Additive Manufacturing Prospective 26 April 2021 Pages: 197 - 212