Historical Review on the Boriding Process using Bibliometric Analysis R. A. García-LeónJ. Martínez-TrinidadI. Campos-Silva Review 17 January 2021 Pages: 541 - 557
Cold Spray of Metal Powder Mixtures: Achievements, Issues and Perspectives A. SovaM. DoubenskaiaI. Smurov Review 22 January 2021 Pages: 559 - 570
An Investigation into Pre-concentration of Low-Grade Silica-Rich Malanjkhand Copper Ore by Wilfley Table Silpa Sweta JenaS. I. AngadiR. Venugopal Original Article 22 January 2021 Pages: 571 - 581
Fabrication of Al/Cu Composite Reinforced with AISI 304 Stainless Steel Wires Through Accumulative Roll Bonding and Evaluation of Their Mechanical Properties E. MostafazadehH. Jafarzadeh Original Article 22 January 2021 Pages: 583 - 591
Microstructural Studies of Composite (Cr3C2–NiCr) Laser Clads Developed on Preheated Substrate T91 Ajit M. HebbaleManish TakRavi Bathe Original Article 22 January 2021 Pages: 593 - 600
Resistance Spot Welding Behavior of Automotive Steels Saurabh AkulwarArbind AkelaMadhu Ranjan Original Article 22 January 2021 Pages: 601 - 609
Theoretical Analysis of Hysteresis and Characteristic Transition Temperatures of Iron-Based Memory Metals V. SampathSai Venkata Gayathri AyyagariA. Anusha Original Article 22 January 2021 Pages: 611 - 618
Selective Flocculation of Chromite Tailings Lopamudra PandaR. VenugopalN. R. Mandre Original Article 23 January 2021 Pages: 619 - 628
Abrasive Wear Investigation and Parametric Process Optimization of in situ Al–4.5%Cu–xTiB2 Composites Shaik MozammilEklavya KoshtaP. K. Jha Original Article 26 January 2021 Pages: 629 - 648
Computational Modeling of Compressive Behavior of Wire-Reinforced Bulk Metallic Glass Matrix Composites Hamidreza Daghigh ShiraziMehdi Malekan Original Article 02 February 2021 Pages: 649 - 658
Experimental Investigation of the Effect of Independent Parameters in the Face Milling of Aluminum 6082 Alloy M. VaratharajuluMuthukannan DuraiselvamRamkumar Sathiyamurthy Original Article 02 February 2021 Pages: 659 - 677
Improvement of Tensile and Fracture Toughness Properties of Al 2014 Alloy Processed by Different Rolling Method followed by Post-ageing Treatment Manoj Kumar PathakAmit JoshiK. K. S. Mer Original Article 03 February 2021 Pages: 679 - 689
Analysis of Surface Roughness, Sound Level and Machine Current in the Turning of Hardened AISI S1 Steel A. K. Cakir Original Article 03 February 2021 Pages: 691 - 703
Effects of Brass Interlayer on Mechanical Properties of Friction Stir Welded AA 6061-T6 Joint Rishabh SwarnkarSohan ChaudharyRaj Ballav Original Article 04 February 2021 Pages: 705 - 711
Rate-Limiting Mechanism in Iron Ore Sintering Process with Waste Gas Recycling Veera Brahmacharyulu AngalakuditiSudhakar KarreSaroj Sundar Baral Original Article 04 February 2021 Pages: 713 - 723
Effect of Forming-Die Temperature on Microstructure and Mechanical Properties of AA7075 Alloy During HFQ® Process Y. F. JiangH. DingY. S. Zhang Original Article 04 February 2021 Pages: 725 - 734
Effect of Carbon Addition on Mechanical Properties and Dry Sliding Behavior of Fe-0.65P Alloy Processed by Powder Forging S. K. ChaurasiaVikram V. DabhadeS. K. Nath Original Article 06 February 2021 Pages: 735 - 742
Influence of Ti3AlC2 Ceramic Particles in AZ91 Alloy: Produced by Melt Infiltration Method Deepa RaniLingappa RangarajK. Venkateswarlu Original Article 06 February 2021 Pages: 743 - 752
Concurrent Enhancement of Strength and Corrosion Resistance in Ultrafine-grained Al6063 Tubes M. EbrahimiC. GodeR. Berjis Original Article 07 February 2021 Pages: 753 - 766
Spheroidization of 100Cr6 Bearing Steel by Warm Forging M. VidhyasagarG. Balachandran Original Article 08 February 2021 Pages: 767 - 774
