Electrochemical etching technique for tungsten electrodes with controllable profiles for micro-electrical discharge machining Thanh-Hung DuongHyun-Chul Kim OriginalPaper 09 June 2015 Pages: 1053 - 1060
Analysis of pressure distribution and verification of pressure signal by changes load and velocity in chemical mechanical polishing Changsuk LeeJaehong ParkHaedo Jeong OriginalPaper 09 June 2015 Pages: 1061 - 1066
A Fuzzy-P controller of an active reaction force compensation (RFC) mechanism for a linear motor motion stage Duc Canh NguyenHyeong-Joon Ahn OriginalPaper 09 June 2015 Pages: 1067 - 1074
A wirelessly powered expanding-extending robotic capsule endoscope for human intestine Shu HeGuo-Zheng YanWen-Wen Chen OriginalPaper 09 June 2015 Pages: 1075 - 1084
Observer-based dynamic parameter identification for wheeled mobile robots Ngoc-Bach HoangHee-Jun Kang OriginalPaper 09 June 2015 Pages: 1085 - 1093
Primary stability evaluation of a hip-joint implant systems according to different surgical methods and bone densities under cyclic loading condition Sang-Young KimSoo ParkChang-Sung Seok OriginalPaper 09 June 2015 Pages: 1095 - 1100
FEM analysis on the influence of rounded tool edge on micro-blanking of thin foil with negative clearance Shin-Hyung SongWoo Chun Choi OriginalPaper 09 June 2015 Pages: 1101 - 1105
A diagnosis and evaluation method for strategic planning and systematic design of a virtual factory in smart manufacturing systems SangSu ChoiBo Hyun KimSang Do Noh OriginalPaper 09 June 2015 Pages: 1107 - 1115
A study on the compression property of sandwich composite with porous core Seung-Ok BangJae-Ung Cho OriginalPaper 09 June 2015 Pages: 1117 - 1122
Study on modular modeling and performance evaluation of a conical gear for marine transmission system Zhe-Zhu XuJun-seong KimSung-Ki Lyu OriginalPaper 09 June 2015 Pages: 1123 - 1128
Effect of cathode flow field configuration on air-breathing proton exchange membrane fuel cell Woong Ki JangJongpil ChoiByeong Hee Kim OriginalPaper 09 June 2015 Pages: 1129 - 1134
Joining performance evaluation of different types of GEP224 glass/epoxy-to-AZ31B magnesium alloy singlelap joints Jung-Seok KimJae-Young LimWoo-Geun Lee OriginalPaper 09 June 2015 Pages: 1135 - 1140
An optimal design of the internal space in a micro-speaker module Dong-Cheol KimHyun-Yong Jeong OriginalPaper 09 June 2015 Pages: 1141 - 1147
Optimization of the hot workability for an extrude AZ80 Mg alloy using the processing map and Kriging meta-model Sang Kyun OhKwang Ki LeeYoung Suk Kim OriginalPaper 09 June 2015 Pages: 1149 - 1156
An efficient contour parallel tool path generation for arbitrary pocket shape without uncut regions Elhachemi- BahloulMourad- BriouaCherif- Rebiai OriginalPaper 09 June 2015 Pages: 1157 - 1169
In vivo evaluation of the subject-specific finite element model for knee joint cartilage contact area Kyoung-Tak KangSung-Hwan KimHeoung-Jae Chun OriginalPaper 09 June 2015 Pages: 1171 - 1177
A comparison of four different muscle pennation models and their effects on predictions in peak fiber force and operating range of fiber length Jongsang SonYoungho Kim OriginalPaper 09 June 2015 Pages: 1179 - 1185
Experimental study of vibrational energy harvesting using Electro-Active paper Zafar AbasHeung Soo KimJaehwan Kim OriginalPaper 09 June 2015 Pages: 1187 - 1193
Empirical evidence of AMT practices and sustainable environmental initiatives in malaysian automotive SMEs Siti Zawiah Md DawalFarzad TahririNovita Sakundarini OriginalPaper 09 June 2015 Pages: 1195 - 1203
Compensation of tool deflection in micromilling using workpiece holder control device Segon HeoMingyu LeeByung-Kwon Min OriginalPaper 09 June 2015 Pages: 1205 - 1208
Muscular activity analysis of haptic-based resistance training machine compared with dumbbell training Gwanhyeong ChaKyungnam KimWoojin Chung OriginalPaper 09 June 2015 Pages: 1209 - 1213
Endoscopic suturing device using new reciprocating curved needle: An Ex Vivo comparison study Semi YoonHyuk-Soon ChoiHoon-Jai Chun OriginalPaper 09 June 2015 Pages: 1215 - 1219
