In-process measurement of surface roughness using machine vision with sub-pixel edge detection in finish turning Mohan Kumar BalasundaramMani Maran Ratnam OriginalPaper 28 November 2014 Pages: 2239 - 2249
Development of a high precision coplanar stage by using miniature Michelson interferometer Kuang-Chao FanHao ZhouRuijun Li OriginalPaper 28 November 2014 Pages: 2251 - 2256
Simultaneous identification of joint compliance and kinematic parameters of industrial robots Jian ZhouHoai-Nhan NguyenHee-Jun Kang OriginalPaper 28 November 2014 Pages: 2257 - 2264
Energy consumption of the brushing process for PCB manufacturing based on a friction model Hae-Sung YoonEun-Seob KimSung-Hoon Ahn OriginalPaper 28 November 2014 Pages: 2265 - 2272
Design of high strength differential TWB to enhance drawability: FE study and optimization Ngoc-Trung NguyenKrishnaswamy HariharanMyoung-Gyu Lee OriginalPaper 28 November 2014 Pages: 2273 - 2283
Rotordynamic modelling and analysis of a radial inflow turbine rotor-bearing system Hyung-Chul JungSusan Krumdieck OriginalPaper 28 November 2014 Pages: 2285 - 2290
Fatigue life estimation of cold drawn contact wire Zhen GuoYong-Seok KimSam-Young Kwon OriginalPaper 28 November 2014 Pages: 2291 - 2299
Effect of pad’s surface deformation and oscillation on monocrystalline silicon wafer surface quality Woong-Kirl ChoiSeong-Hyun KimChul-Hee Lee OriginalPaper 28 November 2014 Pages: 2301 - 2307
Multi-objective optimization of single point incremental sheet forming of AA5052 using Taguchi based grey relational analysis coupled with principal component analysis Pandivelan ChinnaiyanA. K. Jeevanantham OriginalPaper 28 November 2014 Pages: 2309 - 2316
Design of micro biopsy device for wireless autonomous endoscope Wen-Wen ChenGuo-Zheng YanZhi-Wu Wang OriginalPaper 28 November 2014 Pages: 2317 - 2325
Investigation of the power losses from hydrostatic piston shoe bearings for swash plate type axial piston pumps under mixed friction conditions Yeh-Sun HongYong-Cheol Kwon OriginalPaper 28 November 2014 Pages: 2327 - 2333
Geometry design of vertical probe needle using mechanical testing and finite element analysis Hyock-Ju KwonJiwon LeeChang Min Im OriginalPaper 28 November 2014 Pages: 2335 - 2342
A novel approach in manufacturing two-stepped tubes using a multi-stage die in tube hydroforming process Hamed Ziaei PoorHossain Ghorbani MenghariHamed Sanei OriginalPaper 28 November 2014 Pages: 2343 - 2350
Multi objective optimization of friction stir welding parameters using FEM and neural network Mohammad Hasan ShojaeefardMostafa AkbariParviz Asadi OriginalPaper 28 November 2014 Pages: 2351 - 2356
An analyzing method of coupled modes in multi-stage planetary gear system Wei SunXin DingQingguo Wang OriginalPaper 28 November 2014 Pages: 2357 - 2366
Dynamic analysis and iterative design of a passive reaction force compensation device for a linear motor motion stage Duc Canh NguyenHyeong Joon Ahn OriginalPaper 28 November 2014 Pages: 2367 - 2373
Development of a high-speed and precision micro-spindle for micro-cutting Wei LiZhi-Xiong ZhouYong Du OriginalPaper 28 November 2014 Pages: 2375 - 2383
A simple approach for an ultra-precise patterning using deep x-ray lithography with a micron-patterned x-ray mask Jong Hyun KimSuk Sang ChangGeunbae Lim OriginalPaper 28 November 2014 Pages: 2385 - 2390
The effect of Ti adhesion layer on the thermoelectric noise of a high resolution thermopile for nanowatt heat flux sensor Sung-Ki NamSun-Kyu Lee OriginalPaper 28 November 2014 Pages: 2391 - 2396
Evaluation of surface wettability by means of the measurement of the adhesive force between a microstructured hydrophobic surface and a water droplet Jae Min LeeMin Chul LeeJong Soo Ko OriginalPaper 28 November 2014 Pages: 2397 - 2404
Development of a new head/brain model for the prediction of subdural hemorrhage In Seok HanYoung Eun Kim OriginalPaper 28 November 2014 Pages: 2405 - 2411
Development of mask-less projection slurry stereolithography for the fabrication of zirconia dental coping Cho-Pei JiangHan-Jan HsuShyh-Yuan Lee OriginalPaper 28 November 2014 Pages: 2413 - 2419
Material pixel-based process planning for layered manufacturing of heterogeneous objects Hong Seok KimKi-Hoon Shin OriginalPaper 28 November 2014 Pages: 2421 - 2427
Study on multiple die stretch forming for curved surface of sheet metal Ji-Woo ParkYu-Beom KimBeom-Soo Kang OriginalPaper 28 November 2014 Pages: 2429 - 2436
Quantitative analysis on air-dispensing parameters for manufacturing dome lenses of chip-on-board LED system Eun-chae JeonJe-Ryung LeeHwi Kim OriginalPaper 28 November 2014 Pages: 2437 - 2441
The effects of minimum quantity lubrication (MQL) on machining force, temperature, and residual stress Xia JiBeizhi LiSteven Y. Liang OriginalPaper 28 November 2014 Pages: 2443 - 2451
A study on development of rotary structure for tracking-type floating photovoltaic system Young-Kwan ChoiYoung-Geun Lee OriginalPaper 28 November 2014 Pages: 2453 - 2460
Improvement of crack sizing performance by using nonlinear ultrasonic technique Hogeon SeoKyung-Young JhangDong-Pyo Hong Short Communication 28 November 2014 Pages: 2461 - 2464
Comparison benefit of e-transmission for NEV Ilseon SohnBumjoon Kim Short Communication 28 November 2014 Pages: 2465 - 2468
Fabrication of micro-scale wrinkles on a curved surface using weak-polymerization and surface shrinkage Hee-Jin ParkChangmin SonSang-Hu Park Short Communication 28 November 2014 Pages: 2469 - 2471
Consistency of the optimized bandwidth in filter-based fatigue index Jungyoon KimJongsang SonYoungho Kim Short Communication 28 November 2014 Pages: 2473 - 2477
