1. A study on deburring of magnesium alloy plate by magnetic abrasive polishing

   • Tae-Wan Kim
   • Jae-Seob Kwak

   OriginalPaper 21 May 2010 Pages: 189 - 194

2. A study on the machining of compressor rotors using formed tools

   • Sang-Yoon Park
   • Lee Hi-Koan
   • Mun Sang-Don

   OriginalPaper 21 May 2010 Pages: 195 - 200

3. Generation of velocity profiles with speed limit of each axis for high-speed machining using look-ahead buffer

   • Cheol-Soo Lee

   OriginalPaper 21 May 2010 Pages: 201 - 208

4. Sensitivity control of a MR-damper semi-active suspension

   • Arjon Turnip
   • Seonghun Park
   • Keum-Shik Hong

   OriginalPaper 21 May 2010 Pages: 209 - 218

5. Torque sensor calibration using virtual load for a manipulator

   • Sang-Hyuk Lee
   • Young-Loul Kim
   • Jae-Bok Song

   OriginalPaper 21 May 2010 Pages: 219 - 225

6. A robust control of electro hydrostatic actuator using the adaptive back-stepping scheme and fuzzy neural networks

   • Han Me Kim
   • Sung Hwan Park
   • Jong Shik Kim

   OriginalPaper 21 May 2010 Pages: 227 - 236

7. Fault detection of cycle-based signals using wavelet transform in FAB processes

   • Jun Seok Kim
   • Jae Hyun Lee
   • Sung-Shick Kim

   OriginalPaper 21 May 2010 Pages: 237 - 246

8. Edge identification of a small object through a low-resolution tactile sensor array

   • Tri Cong Phung
   • Yong Seok Ihn
   • Hyouk Ryeol Choi

   OriginalPaper 21 May 2010 Pages: 247 - 254

9. Enhanced SLAM for a mobile robot using extended Kalman Filter and neural networks

   • Kyung-Sik Choi
   • Suk-Gyu Lee

   OriginalPaper 21 May 2010 Pages: 255 - 264

10. Development and application of VPG simulation technique based on equivalent virtual road profile

    • Dae-Oh Kang
    • Kihong Park
    • Jay Il Jeong

    OriginalPaper 21 May 2010 Pages: 265 - 272

11. Rapid surface reconstruction from a point cloud using the least-squares projection

    • Dong-Jin Yoo

    OriginalPaper 21 May 2010 Pages: 273 - 283

12. Simulations of the vibration response of mannequins in car seats by changing parameter and excitation

    • Seong Keol Kim

    OriginalPaper 21 May 2010 Pages: 285 - 289

13. A new approach for molding multi component parts

    • Hong-Seok Park
    • Dinh Ba Hung Anh

    OriginalPaper 21 May 2010 Pages: 291 - 297

14. Development of an apparatus for removing magnetic sludge by permanent magnets setup in the condenser of the power plant

    • Jun-Ho Bae
    • Moon-Saeng Kim
    • Chul Kim

    OriginalPaper 21 May 2010 Pages: 299 - 307

15. Fracture toughness of CFRP laminated plates according to resin content

    • In Young Yang
    • Joo Yeong Jeong
    • Ji Hoon Kim

    OriginalPaper 21 May 2010 Pages: 309 - 313

16. Assessment of running safety of railway vehicles using multibody dynamics

    • Beom-Gyu Eom
    • Hi Sung Lee

    OriginalPaper 21 May 2010 Pages: 315 - 320

17. Preparation and absorption properties of ZnO nanostructures for cleanup of H₂S contained gas

    • No-Kuk Park
    • Gi Bo Han
    • Tae Jin Lee

    OriginalPaper 21 May 2010 Pages: 321 - 325

18. NC machining of free-form Kriging surfaces

    • Abbas Vafaeesefat

    OriginalPaper 21 May 2010 Pages: 327 - 333

19. Three-dimensional microstructure using partitioned cross-sections in projection microstereolithography

    • Young-Myoung Ha
    • In-Baek Park
    • Seok-Hee Le

    OriginalPaper 21 May 2010 Pages: 335 - 340

20. Tool wear, chip formation and workpiece surface issues in CBN hard turning: A review

    • Manu Dogra
    • Vishal S. Sharma
    • Jasminder Singh Dureja

    ReviewPaper 21 May 2010 Pages: 341 - 358