Abstract
Drilling is one of the most important machining operations in manufacture process. When drilling process is applied, unexpected burrs will be formed on the surface of workpiece. Even a small burr can cause unwanted problems, resulting in low quality products. In order to get better drilled parts, it is very important to know characteristics of burr formation and to remove the burr from the drilled surface with machining process. In this study, magnetic abrasive polishing (MAP) was used to research the deburring factors of magnesium alloy. Moreover, design of experiments was performed to evaluate parameters’ effect on the MAP process. As a result, it was seen that the MAP was useful to remove the burrs on the workpiece without damage from its original surface.
Similar content being viewed by others
References
Chung, I. D., Kim, J. D. and Kang, K. H., “Ablation Drilling of Invar Alloy Using Ultra-short Pulsed Laser,” Int. J. Precis. Eng. Manuf., Vol. 10, No. 2, pp. 11–16, 2009.
Xia, W., Chen, Z., Chen, D. and Zhu, S., “Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets Produced by Differential Speed Rolling,” Journal of Materials Processing Technology, Vol. 209, No. 1, pp. 26–31, 2009.
Lin, B. T. and Kuo, C. C., “Application of an Integrated RE/RP/CAD/CAE/CAM System for Magnesium Alloy Shell of Mobile Phone,” Journal of Materials Processing Technology, Vol. 209, No. 6, pp. 2818–2830, 2009.
Hwang, J. K. and Kang, D. M., “FE Analysis on the Press Forging of AZ31 Magnesium Alloy,” Transaction of the Korean Society of Automotive Engineers, Vol. 14, No. 1, pp. 81–91, 2006.
Sohn, K. Y., “The Effect of Heat Treatment and Extruded Mg-Al-Zn Alloy,” Material Science Forum, Vol. 419–422, pp. 135–140, 2003.
Yin, S. and Shinmura, T., “A Comparative Study: Polishing Characteristics and Its Mechanisms of Three Vibration Modes in Vibration-assisted Magnetic Abrasive Polishing,” International Journal of Machine Tools and Manufacture, Vol. 44, No. 4, pp. 383–390, 2004.
Kim, S. O. and Kwak, J. S., “Effect of Magnetic Abrasive Polishing on Surface Quality of Different Kinds of Materials,” Proceedings of International Symposium on Advanced Mechanical and Power Engineering, pp. 27–31, 2008.
Kwak, J. S. and Kim, Y. S., “Mechanical Properties and Grinding Performance on Aluminum-based Metal Matrix Composites,” International Journal of Materials Processing Technology, Vol. 201, No. 1–3, pp. 596–600, 2008.
Hwang, Y. K., Lee, C. M. and Park, S. H., “Evaluation of Machinability According to the Changes in Machine Tools and Cooling Lubrication Environments and Optimization of Cutting Conditions Using Taguchi Method,” Int. J. Precis. Eng. Manuf., Vol. 10, No. 3, pp. 65–73, 2009.
Kwak, J. S., “Application of Taguchi and Response Surface Methodologies for Geometric Error in Surface Grinding Process,” International Journal of Machine Tools and Manufacture, Vol. 45, No. 3, pp. 327–334, 2005.
Yin, S. and Shinmura, T., “Vertical Vibration-assisted Magnetic Abrasive Finishing and Deburring for Magnesium Alloy,” International Journal of Machine Tools and Manufacture, Vol. 44, No. 12–13, pp. 1297–1303, 2004.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kim, TW., Kwak, JS. A study on deburring of magnesium alloy plate by magnetic abrasive polishing. Int. J. Precis. Eng. Manuf. 11, 189–194 (2010). https://doi.org/10.1007/s12541-010-0021-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-010-0021-4