1. Overview of Small Punch Test

   • S. Arunkumar

   ReviewPaper 21 September 2019 Pages: 719 - 738

   

2. High Temperature Plastic Deformation Constitutive Equation of a New Alloy for Piston Ring

   • Dejin Wei
   • Ruirui Liu
   • Haitao Zhou

   ReviewPaper 19 October 2019 Pages: 739 - 746

   

3. Effects of Ga Content on Dynamic Recrystallization and Mechanical Properties of High Strain Rate Rolled Mg–Ga Alloys

   • Wensen Huang
   • Jihua Chen
   • Weijun Zhu

   OriginalPaper 22 July 2019 Pages: 747 - 759

   

4. Microstructural and Mechanical Behavior of Al6061-Graphene Oxide Nanocomposites

   • Mahdi Hedayatian
   • Khodadad Vahedi
   • Amir Momeni

   OriginalPaper 24 July 2019 Pages: 760 - 772

   

5. Effect of pH on Dimethylamine Borane Reduced Electroless Nickel Deposits on AISI/SAE 1045 Steel Surface

   • L. Guerra
   • F. Echeverría
   • E. Correa

   OriginalPaper 17 July 2019 Pages: 773 - 782

   

6. Electrochemical Polishing of Additively Manufactured Ti–6Al–4V Alloy

   • Yifei Zhang
   • Jianzhong Li
   • Yanwen Tian

   OriginalPaper 04 December 2019 Pages: 783 - 792

   

7. AlNiCrFeMn Equiatomic High Entropy Alloy: A Further Insight in Its Microstructural Evolution, Mechanical and Surface Degradation Response

   • E. Ananiadis
   • K. Lentzaris
   • A. E. Karantzalis

   OriginalPaper 31 July 2019 Pages: 793 - 811

   

8. Microstructure and Properties of Electrodeposited nc-TiO₂/Ni–Fe and Ni–Fe Coatings

   • P. Ledwig
   • T. Ratajski
   • B. Dubiel

   OriginalPaper Open access 22 September 2019 Pages: 812 - 826

   

9. Characterization Investigations of 2 wt% LaB₆ Particulate-Reinforced Al-7 wt% Si Matrix Composites Fabricated by Powder Metallurgy Methods

   • Sıddıka Mertdinç
   • Duygu Ağaoğulları
   • M. Lütfi Öveçoğlu

   OriginalPaper 20 July 2019 Pages: 827 - 843

   

10. Mechanical Properties and Microstructural Behaviour of Microwave Sintered WC–Co

    • Raihan Rumman
    • Lee C. Chuan
    • Reza Ghomashchi

    OriginalPaper 24 July 2019 Pages: 844 - 853

    

11. Dissimilar Metal Joining of 304 Stainless Steel to SMA490BW Steel Using the Filler Metal Powders with a High-Entropy Design

    • Dejia Liu
    • Rui Guo
    • Xiangjie Wang

    OriginalPaper 01 August 2019 Pages: 854 - 866

    

12. Microstructure and Charpy Impact Properties of FCAW and SAW Heat Affected Zones of 100 mm Thick Steel Plate for Offshore Platforms

    • Dongki Choi
    • Hun Lee
    • Sang Yong Shin

    OriginalPaper 13 February 2020 Pages: 867 - 881

    

13. Processing Route Effects on the Mechanical and Corrosion Properties of Dual Phase Steel

    • Maryam Soleimani
    • Hamed Mirzadeh
    • Changiz Dehghanian

    OriginalPaper 14 October 2019 Pages: 882 - 890

    

14. Calibration of Laser Penetration Depth and Absorptivity in Finite Element Method Based Modeling of Powder Bed Fusion Melt Pools

    • Jaewoong Kim
    • Seulbi Lee
    • Yoon Suk Choi

    OriginalPaper 10 January 2020 Pages: 891 - 902

    

15. Correction to: Calibration of Laser Penetration Depth and Absorptivity in Finite Element Method Based Modeling of Powder Bed Fusion Melt Pools

    • Jaewoong Kim
    • Seulbi Lee
    • Yoon Suk Choi

    Correction 25 February 2020 Pages: 903 - 904

    

16. Microstructural and Mechanical Properties of TiC_X–Ni₃(Al,Ti)/Ni Functionally Graded Composites Fabricated from Ti₃AlC₂ and Ni Powders

    • Guangming Zheng
    • Zhenying Huang
    • Hongxiang Zhai

    OriginalPaper 22 July 2019 Pages: 905 - 913