Influence of strain rate on the behavior of constructional alloys in static tension under conditions of extreme cooling (4.2 K) V. A. StrizhaloV. Yu. BugaevI. I. Medved' Scientific and Technical Section Pages: 1 - 7
Simulating the behavior of the material in the vicinity of wedge-shaped zones of engine components G. N. Tret'yachenkoV. G. Barilo Scientific and Technical Section Pages: 8 - 15
Kinetics of damage cumulation in materials of flexible vacuum elements L. R. BotvinaA. I. DanilovI. B. Oparina Scientific and Technical Section Pages: 15 - 20
Load-carrying capacity of circular cylindrical shells in cyclic loading with internal pressure V. N. BastunL. M. Shkaraputa Scientific and Technical Section Pages: 20 - 24
Cold resistance of steels in static loading in conditions with high plastic strains A. V. VikulinA. V. Popkov Scientific and Technical Section Pages: 24 - 28
Durability and dislocation structure of nickel at high loading frequency V. B. ShevchenkoT. A. MolodkinaYu. F. Lugovskoi Scientific and Technical Section Pages: 29 - 33
Fracture mechanics of multilayer and reinforced spherical type pressure vessels at reduced test temperature S. V. SerikovYu. I. PashkovN. A. Zvonarev Scientific and Technical Section Pages: 33 - 38
Determination of the stress intensity factor by methods of photoelastic simulation A. A. OstseminS. A. DeniskinL. L. Sitnikov Scientific and Technical Section Pages: 39 - 45
Fracture surface formation of ceramics in the precritical crack growth range V. G. Borovik Scientific and Technical Section Pages: 45 - 51
Effect of substructure on crack formation and total failure of industrial alloys of the aluminium-copper-magnesium system under low-cycle fatigue conditions V. V. TeleshovV. I. KuzginovL. A. Nosik Scientific and Technical Section Pages: 52 - 59
Creep of medium and high strength aluminum alloys at normal temperature in moist atmospheres V. M. PolyanskiiN. I. VolkovA. N. Khailov Scientific and Technical Section Pages: 59 - 70
Effect of technological factors on the compressive strength of sitalls (glass ceramics) G. S. PisarenkoYu. M. RodichevA. M. Raikhel' Scientific and Technical Section Pages: 71 - 78
Strength of a structurally inhomogeneous material under axial tension V. A. NikitinI. A. Sazonov Scientific and Technical Section Pages: 79 - 82
Experimental determination of the strength of reinforced dies V. G. SynkovA. A. Strebul'T. R. Rezakova Scientific and Technical Section Pages: 83 - 86
Structural factors determining the change in young's modulus of polycrystalline carbon materials in heat treatment I. Ya. LevintovichA. S. Kotosonov Scientific and Technical Section Pages: 86 - 91
Influence of deformation anisotropy on the size of the plastic zone at the tip of an opening mode crack V. N. Bastun Scientific and Technical Section Pages: 91 - 95
Computing the limiting state of banded pipes V. Yu. ZavarukhinA. A. Ostsemin Scientific and Technical Section Pages: 95 - 102
Determining the stiffnesses of structural components with a periodic structure V. I. Antonenko Scientific and Technical Section Pages: 102 - 108
Computation of the thermoelastic deformation of three-dimensional pipeline components of complex shape A. M. Timonin Scientific and Technical Section Pages: 108 - 112
Reduction of residual stresses in welded plates by local heat treatment using moving heat sources L. V. KhomlyakV. N. MaksimovichA. Z. Kuz'menko Scientific and Technical Section Pages: 113 - 117
Construction of discretely equal-strength systems based on an algorithm of iterative interaction of local and general deformations I. N. SerpikV. G. Medvedev Scientific and Technical Section Pages: 117 - 122
Calculation and experimental method of estimating the cold resistance of structural elements of steel A. V. Vikulin Scientific and Technical Section Pages: 122 - 127
Automatic system of programmed control of parameters of vibration and thermal tests of gas turbine engine blades (ASPC VTT) V. T. TroshchenkoV. S. KostenkoK. G. Svyatyshev Production Section Pages: 128 - 132
Nondestructive method of checking the strength of joints with interference fit V. F. TikhonovM. K. KravtsovB. M. Arpent'ev Production Section Pages: 133 - 138
Computerized automated system for measuring the vibration-damping characteristics of mechanical systems A. G. BaskovA. G. KratkoB. S. Chaikovskii Production Section Pages: 138 - 140
Apparatus for experimental investigation of the bearing capacity of shell structures subjected to a combined loading O. M. Dubovik Production Section Pages: 140 - 143
Effectiveness of strengthening by surface plastic deformation of threaded and gear parts with partial cutting of the work hardened layer I. B. VolkovL. M. BelkinL. D. Kotel'nikov Production Section Pages: 143 - 147
Limiting state of radial turbine rotors V. É. GokhbergO. S. Sadakov Production Section Pages: 147 - 150
Microinhomogeneity of deformation and mechanical properties of steel in static and impact tests L. V. Kuksa Production Section Pages: 150 - 153