International conference on aluminum alloys ICAA12 N. A. BelovV. V. AntipovD. G. Eskin OriginalPaper 05 February 2012 Pages: 405 - 407
Recent trends in the science and technology of crystallization of aluminum alloys D. G. Eskin OriginalPaper 05 February 2012 Pages: 408 - 413
Special features of crystallization of scandium-alloyed aluminum alloys V. V. Zakharov OriginalPaper 05 February 2012 Pages: 414 - 419
Sparingly alloyed high-strength aluminum alloys: principles of optimization of phase composition N. A. Belov OriginalPaper 05 February 2012 Pages: 420 - 427
High-strength Al – Zn – Mg – Cu alloys and light Al – Li alloys V. V. AntipovO. G. SenatorovaR. O. Vakhromov OriginalPaper 05 February 2012 Pages: 428 - 433
About some aspects of production of cast shapes from “secondary” silumins in Russia V. D. BelovN. A. Belov OriginalPaper 05 February 2012 Pages: 434 - 439
Structure, properties and application of alloys of the Al – Mg – Si – (Cu) system N. I. KolobnevL. B. BerD. K. Ryabov OriginalPaper 05 February 2012 Pages: 440 - 444
Weldability and properties of welds of high-strength aluminum alloys of the Al – Cu – Li system A. M. DritsV. V. Ovchinnikov OriginalPaper 05 February 2012 Pages: 445 - 449
Effect of annealing on the structure and properties of aluminum alloy Al – 8% MM A. A. MoguchevaD. V. ZyabkinR. O. Kaibyshev OriginalPaper 05 February 2012 Pages: 450 - 454
Comparative analysis of alloying additives as applied to the production of heat-resistant aluminum-base wires N. A. BelovA. N. AlabinA. R. Teleuova OriginalPaper 05 February 2012 Pages: 455 - 459
Casting of aluminum alloys with pressure crystallization. Part 1 K. A. Batyshev Aluminum Alloys 05 February 2012 Pages: 463 - 471
Aluminum-base amorphous and nanocrystalline materials D. V. Louzguine-Luzgin OriginalPaper 05 February 2012 Pages: 472 - 477
Production of additions for aluminum alloys V. I. NapalkovS. V. MakhovD. A. Popov OriginalPaper 08 February 2012 Pages: 478 - 483
Reconditioning heat treatment of tpp steam pipes by induction heating with mobile inductor G. S. ZislinN. I. Kamenskaya Heat Treatment 05 February 2012 Pages: 484 - 490
Choice of tempering mode for relieving stresses in parts L. B. GetsovN. A. KatanahaYu. K. Petrenya OriginalPaper 05 February 2012 Pages: 491 - 494
Structure and mechanical properties of rapidly quenched Al – 5% Mg alloy after heat treatment El Said Gouda OriginalPaper 05 February 2012 Pages: 495 - 497
Structural and kinetic features of dynamic recrystallization of alloyed austenite upon multipass hot deformation I. N. KunitskayaYa. I. SpektorV. E. Olshanetskii Deformation 05 February 2012 Pages: 498 - 502
High cold plastic deformation of die steel 4Kh5VF1S subjected to hardening and tempering Jun ShenXianshun WeiB. S. Vekshin OriginalPaper 05 February 2012 Pages: 503 - 504
Fabrication of high-strength Ti – 6% Al – 4% V titanium alloy by multipass warm rolling S. V. S. Narayana MurtyNiraj NayanP. P. Sinha OriginalPaper 05 February 2012 Pages: 505 - 507
High-temperature gas corrosion of austenitic Cr – Ni steel containing Mo and Ti D. S. StavrevTs. D. DikovaI. P. Ivanov Corrosion 05 February 2012 Pages: 508 - 511