Continuous fiber reinforced mullite matrix composites by sol–gel processing: Part II Properties and fracture behaviour J WuF. R JonesP. F James OriginalPaper Pages: 3629 - 3635
Effect of electron-beam irradiation on water wettability of hydroxy apatites for artificial bone Y NishiH IzumiM Ochi OriginalPaper Pages: 3637 - 3639
Fatigue fracture mechanisms and fractography of short-glassfibre-reinforced polyamide 6 J. J HorstJ. L Spoormaker OriginalPaper Pages: 3641 - 3651
Preparation of the Bi8Sb32Te60 solid solution by mechanical alloying P PierratA DauscherH Scherrer OriginalPaper Pages: 3653 - 3657
Preparation and properties of barium titanate glass-ceramics sintered from sol–gel-derived powders KUI YaoLiangying ZhangWeiguang Zhu OriginalPaper Pages: 3659 - 3665
Growth crystallography of Bi12SiO20 single crystals solidified by a floating zone method Senlin FuHiroyuki Ozoe OriginalPaper Pages: 3667 - 3674
Deformation of spherulitic polyethylene thin films M. F ButlerA. M Donald OriginalPaper Pages: 3675 - 3685
Long term coarsening of γ′ precipitates in a Ni-base superalloy A GesO FornaroH Palacio OriginalPaper Pages: 3687 - 3691
Corrosion inhibition of Al–bronze in acidified 4% NaCl solution A. A El-WarrakyH. A El-Dahan OriginalPaper Pages: 3693 - 3700
HgO as an internal oxygen source in Y1Ba2Cu3O7-δ A PandeyY. S ReddyR. G Sharma OriginalPaper Pages: 3701 - 3703
Electrical and morphological characterization of a nickel–polyester composite prepared by spreading and spraying techniques M. M DavilaM. P ElizaldeR Silva OriginalPaper Pages: 3705 - 3710
Evaluation of the statistical parameters of a Weibull distribution M. R GurvichA. T DibenedettoA Pegoretti OriginalPaper Pages: 3711 - 3716
Effect of 1,3-bis(citraconimidomethyl) benzene on the aerobic and anaerobic ageing of diene rubber vulcanizates N. R KumarA. K ChandraR Mukhopadhyay OriginalPaper Pages: 3717 - 3725
Effect of silicon ion implantation on the properties of a cast Co–Cr–Mo alloy M KaminskiJ BaszkiewiczJ Jagielski OriginalPaper Pages: 3727 - 3732
The kinetics of decomposition of solid solutions V. V SlezovYA. J TkatchJ Schmelzer OriginalPaper Pages: 3739 - 3747
Composition dependence of discontinuousmagnetization in CuxFe3-xO4+δ A. H WafikA. M Abd-El-RahmanS. A Mazen OriginalPaper Pages: 3749 - 3752
Processing, sintering characteristics and dielectric properties of barium-substituted Pb(Mg1/3Nb2/3)O3–PbTiO3 solid solution J. P GuhaG. H Haertling OriginalPaper Pages: 3753 - 3758
Microstructural investigation of Bi–Sr–Ca–Cu–oxide thick films on alumina substrates J. A AlarcoA IlushechkinI. D. R Mackinnon OriginalPaper Pages: 3759 - 3764
Crystal growth of selected II–VI semiconducting alloys by directional solidification: Part I Ground-based experiments CHING-HUA SuYI-GAO ShaR. N Scripa OriginalPaper Pages: 3765 - 3768
Determination of the parent grain orientation and habit plane normals for β′1 martensite in a Cu–Al–Ni–Mn shape memory alloy L ChenD. P DunneN. F Kennon OriginalPaper Pages: 3769 - 3773
Mechanism of film growth during anodizing of Al-alloy-8090/SiC metal matrix composite in sulphuric acid electrolyte M Shahid OriginalPaper Pages: 3775 - 3781
Dielectric relaxations in liquid-impregnated porous solids B NettelbladG. A Niklasson OriginalPaper Pages: 3783 - 3800
Excimer laser processing of chemical vapour-deposited diamond fibres G MeadenP. G PartridgeM. N. R Ashfold OriginalPaper Pages: 3801 - 3806
Processing of spodumene-modified mullite ceramics I. M LowE MathewsX. M Pillai OriginalPaper Pages: 3807 - 3812
Anisotropy of creep deformation rate in hot-pressed Si3N4 with preferred orientation of the elongated grains S. Y YoonT AkatsuE Yasuda OriginalPaper Pages: 3813 - 3819
Solidification microstructure of super-α2 alloy prepared by gas atomization R XuY. Y CuiZ. Q Hu OriginalPaper Pages: 3821 - 3827
Aluminium nitride–molybdenum ceramic matrix composites: influence of molybdenum concentration on the mechanical properties A. A KhanJ. C Labbe OriginalPaper Pages: 3829 - 3833
Solid-state reaction in nanocrystalline Fe/SiC composites prepared by mechanical alloying T. D ShenC. C KochJ. T Wang OriginalPaper Pages: 3835 - 3839
Residual stress and thermal properties of zirconia/metal (nickel, stainless steel 304) functionally graded materials fabricated by hot pressing Yeon-Gil JungSung-Churl ChoiUn-Gyu Paik OriginalPaper Pages: 3841 - 3850
Delamination study using four-point bending of bilayers J ZhangJ. J Lewandowski OriginalPaper Pages: 3851 - 3856
Relaxation time for ionized impurity scattering in compensated n-type Hg1-xCdxTe near x=0.2 P GiraultC BlanchardJ. F Barbot OriginalPaper Pages: 3857 - 3861
Synthesis and characterization of lanthanum phosphate sol for fibre coating Peng ChenTai-Il Mah OriginalPaper Pages: 3863 - 3867
Characterization of molybdenum black coatings on zinc substrates F JahanB. E Smith OriginalPaper Pages: 3869 - 3874
A conduction calorimetric study of early hydration of ordinary Portland cement/high alumina cement pastes Ping GuJ. J Beaudoin OriginalPaper Pages: 3875 - 3881
The mechanical properties of friction welded aluminium-based metal–matrix composite materials Y ZhouJ ZhangZ Wang OriginalPaper Pages: 3883 - 3889
Mechanical properties and microstructural stability of wrought, laser, and electron beam glazed NARloy-Z alloy at elevated temperatures J SinghG JermanA. K Kuruvilla OriginalPaper Pages: 3891 - 3903