A device for automatic deposition of a lubricant under pressure on a threaded surface V. M. Yanko OriginalPaper 28 October 2009 Article: 517
Casting molds for the routine production of plastic hydrocyclone components A. BaranovA. I. ProninM. G. Lagutkin Manufacturing Technology 28 October 2009 Article: 513
Calculating diffusion parameters for a corrosive medium acting on polymer materials O. Yu. ErenkovE. A. MyasnikovR. S. Mazin Materials Science and Corrosion Protection 28 October 2009 Article: 505
Calculating the heights of a standard series of scrubbers working with complete evaporation of the irrigating liquid A. Yu. Val’dbergT. N. KuzinaYu. V. Bykova OriginalPaper 28 October 2009 Article: 500
Granulation in technology for utilization of industrial waste materials T. N. Il’inaE. I. Gibelev OriginalPaper 28 October 2009 Article: 495
Ecological monitoring of a megalopolis atmosphere Yu. I. BelyaevD. P. VentK. P. Latyshenko Industrial Ecology 28 October 2009 Article: 491
A new approach to procedure for calculating head characteristics of worms and axial-vortex pump stage B. N. Zotov Compressors, Pumps, and Pipeline Fittings 30 October 2009 Article: 484
Methodological principles of measurements of nitrogen and helium concentrations in liquid propellant constituents V. A. Buzanovskii Cryogenic Engineering, Production and use of Industrial Gases, Refrigeration Engineering 28 October 2009 Article: 478
Formation of secondary drops upon collision of a drop with a liquid surface V. G. SisterO. A. EliseevaA. K. Lednev OriginalPaper 28 October 2009 Article: 473
Effect of particle separation in the curtain of a packed drum vessel O. O. IvanovV. Ya. BorshchevV. N. Dolgunin OriginalPaper 28 October 2009 Article: 468
Mathematical modeling of mass transfer during centrifugal filtration of polydisperse suspensions V. F. PozhidaevYu. B. RubinshteinS. A. Osadchii OriginalPaper 27 October 2009 Article: 460
Polymeric drop-film sprinklers for cooling towers E. V. BoevS. P. IvanovE. A. Nikolaev OriginalPaper 27 October 2009 Article: 454
Processes and equipment for chemical and oil-gas production I. A. KuznetsovaV. M. KlevleevN. S. Trutnev Research, Design, Calculations, and Operating Experience 30 October 2009 Article: 449
The scope for using a vortex tube as a dust trap L. A. TarasovaO. A. TroshkinA. L. Tsvetkov Industrial Ecology 27 October 2009 Article: 443
Mechanical efficiency and losses in a piston compressor for various working bodies Yu. A. AntipovI. A. BarskiiI. K. Shatalov OriginalPaper 27 October 2009 Article: 438
Selection of optimum parameters of pumping equipment at trunk pipeline oil pumping stations R. S. GasparyantsI. V. ShcherbatenkoI. L. Levchenko Compressors, Pumps, and Pipeline Fittings 27 October 2009 Article: 427
Synthesis of a system for monitoring oxygen concentration in working area air V. A. Buzanovskii OriginalPaper 27 October 2009 Article: 422
Physics of processes in the expansion stages of an electrogasdynamic generator with a new electrode system with a pulsed voltage G. I. BumaginYu. A. Bur’yanE. I. Rogal’skii Cryogenic Engineering, Production and use of Industrial Gases, Refrigeration Engineering 27 October 2009 Article: 413
Process control in a single-shaft blade mixer O. V. DeminV. F. PershinM. M. Sviridov OriginalPaper 27 October 2009 Article: 410
A model for the cooling of an elastomer coating on cloth after thermal vulcanization A. A. AvaevYu. R. OsipovV. V. Pavlov OriginalPaper 27 October 2009 Article: 406
Characteristics of effective industrial packings for evaporative cooling of circulating water in cooling towers A. M. KaganA. S. PushnovV. I. Shishov OriginalPaper 27 October 2009 Article: 402
Motion specifics of grinding bodies in vertical planetary mills P. E. VaitekhovichD. V. SemenenkoD. V. Yukhnevich OriginalPaper 27 October 2009 Article: 395
Processes and equipment for chemical and oil-gas production D. A. BaranovA. I. ProninM. G. Lagutkin Research, Design, Calculations, and Operating Experience 30 October 2009 Article: 389