Abstract
Molecular rotors are a group of fluorescent molecules that form twisted intramolecular charge transfer (TICT) states upon photoexcitation. When intramolecular twisting occurs, the molecular rotor returns to the ground state either by emission of a red-shifted emission band or by nonradiative relaxation. The emission properties are strongly solvent-dependent, and the solvent viscosity is the primary determinant of the fluorescent quantum yield from the planar (non-twisted) conformation. This viscosity-sensitive behavior gives rise to applications in, for example, fluid mechanics, polymer chemistry, cell physiology, and the food sciences. However, the relationship between bulk viscosity and the molecular-scale interaction of a molecular rotor with its environment are not fully understood. This review presents the pertinent theories of the rotor-solvent interaction on the molecular level and how this interaction leads to the viscosity-sensitive behavior. Furthermore, current applications of molecular rotors as microviscosity sensors are reviewed, and engineering aspects are presented on how measurement accuracy and precision can be improved.
Similar content being viewed by others
Introduction
The term molecular rotor is commonly used to describe a fluorescent molecule that has the ability to undergo an intramolecular twisting motion in the fluorescent excited state. Typically, a molecular rotor consists of three subunits, an electron donor unit, an electron acceptor unit, and an electron-rich spacer unit that is composed of a network of alternative single and double bonds. This network brings the donor and acceptor units in conjugation, thus facilitating electron movement between this pair, but it ensures minimum overlap of the electron donor and electron acceptor orbitals [1]. In this configuration, the molecule responds to photoexcitation with an intramolecular charge transfer from the donor to the acceptor unit. Whereas the three subgroups assume a planar or near-planar configuration in the ground state, electrostatic forces induce an intramolecular twisting motion of the sub-groups relative to each other [2]. The molecule enters a nonplanar (twisted) state with a lower excited-state energy, and relaxation from the twisted state is associated with either a red-shifted fluorescence emission or nonfluorescent relaxation, depending on the molecular structure [3, 4]. The basic structure of a molecular rotor, together with several typical examples, is shown in Figure 1. Moreover, several chemical classes of molecular rotors exist [5], which are listed in Table 1 together with photophysical characteristics of typical representatives [6–9]. Other fluorophores exist which show predominantly polarity-sensitive behavior that has been attributed to formation of twisted states, but they are much less well-explored than the classes listed in Table 1. Examples are Nile Red [10, 11] and 8-(phenylamino)-1-naphthalenesulfonate (ANS) [12]. A meso-substituted form of dipyrrometheneboron difluoride (BODIPY) has also been hypothesized to form twisted states [13]. However, chemical computations by Kee et al. [13] present a very atypical picture where a planar configuration (0° or 180°) of a 5-aryl-substituted dipyrrin is energetically preferred in the excited state, whereas the lowest-energy angle is 55° in the ground state, i.e., only 35° from perpendicularity. A low degree of rotation would correspond to a low sensitivity towards the environment. For these classes of dyes, further research is needed to understand the specific fluorophore-solvent interactions and the role of segmental mobility in the possible formation of TICT states.
General structure of a molecular rotor ( A ), highlighting the electron donating subunit (green), the electron accepting subunit (red), and the spacer unit (blue), which spatially separates the donor and acceptor groups. Typical representatives are aniline nitriles, such as 1,4-dimethylamino benzonitrile (DMABN, B), julolidine malononitriles, such as 9-(dicyanovinyl) julolidine (DCVJ, C), and stilbenes, such as p-(dimethylamino) stilbazolium (p-DASPMI, D). The arrows indicate bonds around which intramolecular rotation can take place.
Relaxation from the TICT state occurs in one of two ways (see Table 1): In the case of DMABN, the S1 - S0 energy gap in the twisted state is large enough to allow photon emission when the molecule returns to the ground state in a twisted conformation. Such a molecule exhibits a distinct second emission band that is red-shifted from the LE fluorescence. DMABN, for example, has a twisted-state energy gap that is approximately 30% lower than the LE energy gap, and relaxation from both LE and twisted conformation leads to photon emission. Conversely, when the TICT energy gap is much smaller than the LE energy gap, nonradiative relaxation occurs from the TICT conformation. In the example of DCVJ, the twisted-state S1 - S0 energy gap is three times smaller than the LE energy gap [4]. Fluorophores of this class exhibit only a single emission band.
The most notable feature of molecular rotors is the dependency of the twisted state formation rate on the local microenvironment, predominantly the microviscosity of the solvent. In the case of molecular rotors that emit from the twisted state with a red-shifted emission band, steric hindrance of the twisted-state formation in higher-viscosity solvents changes the emission in favor of the shorter-wavelength emission from the planar state [14]. In the case of molecular rotors that exhibit nonradiative relaxation from the twisted state, the fluorescent quantum yield increases in higher-viscosity solvents [15]. The molecular and photophysical phenomena that govern this behavior are explained after the next section.
Biological and Chemical Applications of Molecular Rotors
Bulk viscosity measurement of fluids advertises itself as a possible application. Viscosity changes of protein-containing biofluids, i.e., blood plasma and interstitial fluid, have been linked to various diseases [16] that are mostly associated with altered protein levels. Examples include infections and infarction [17], hypertension [18], diabetes [19], atherosclerosis [20], and normal aging [21]. Furthermore, one of the adverse effects of smoking is elevated plasma viscosity [22], which may be the link between cigarette consumption and cardiovascular disease. The viscosity of lymphatic fluid is directly linked to blood plasma viscosity, because the lymphatic system captures fluid and protein that diffused into the tissue and returns it to the vascular system. Lymphatic fluid viscosity is increased, for example, in conjunction with breast cancer treatment [23], and viscosity changes alter lymphatic fluid circulation during acute shock [24].
Some progress has been made in providing proof-of-principle for this application [25] and in demonstrating that measurement precision of an optical method based on fluorescent molecular rotors is comparable to that of conventional mechanical rheometers [26]. However, few studies exist where bulk viscosity of fluids has been measured with fluorescent molecular rotors. A likely reason is the wide availability of established mechanical rheometers [27]. Moreover, fluorescence-based methods are confounded by the optical properties of the liquid, and correction methods are still under investigation [28]. On the other hand, mechanical rheometers are time-consuming due to single measurements requiring measurement times in the range of minutes, they require scrupulous cleaning and are limited to bulk volumes. These disadvantages make fluorescence-based viscsoity measurements an attractive proposition, most notably due to their considerable speed advantage over mechanical methods [26].
A popular application of molecular rotors is real-time monitoring of aggregation and polymerization processes. Loutfy and Teegarden [29] demonstrated that the emission intensity of DCVJ, but not its peak emission wavelength, strongly depend on the tacticity of PMMA macromolecules: When DCVJ was embedded in PMMA films, it exhibited a quantum yield of 0.015 - 0.020 in syndiotactic PMMA and a slightly higher quantum yield of 0.018 - 0.025 in atactic PMMA. Quantum yield was markedly increased to 0.036 - 0.049 in isotactic PMMA, leading to the conclusion that the flexibility of isotactic chains is lower than that of atactic and syndiotactic chains. Loutfy [30] also demonstrated that the quantum yield of a molecular rotor related to DCVJ increased in polystyrene samples with increasing molecular weight. Similarly, Zhu et al. [31] found that emission of the molecular rotor FCVJ (a hydrophobic ester of (2-carboxy-2-cyanovinyl)-julolidine [7]) is strongly dependent on the chain entanglement in macromolecules - FCVJ fluorescence intensity accurately reported whether polypropylene oxide melts were in the Rouse or the reptation regime.
Molecular rotors have been used to report protein aggregation and protein conformational changes. Hawe et al. [32] showed that heat stressing of immunoglobulin-polysorbate 4 preparations changed the balance of DCVJ and (2-carboxy-2-cyanovinyl)-julolidine towards preferentially binding to polysorbate and thus decreasing their quantum yields. Similar observations were not possible with Nile Red [32]. Not only protein aggregation within the rotor's solvent causes the fluorescence to shift towards emission from the planar state, but also binding of the molecular rotor to a protein. In this context, molecular rotors become fluorescent probes for protein conformational changes and protein assembly. Kung and Reed [33] have shown that DCVJ binds to tubulin, thereby increasing DCVJ quantum yield. DCVJ further increased its fluorescence emission intensity when tubulin aggregated as tubules over tubulin aggregating as sheets [33]. In this study, the peak emission wavelength of DCVJ remained widely constant, indicating that viscosity and polarity do not cause a significant solvatochromic shift, an observation that was later confirmed by our group [34]. Sawada et al. [35] used a molecular rotor related to DCVJ to noncovalently bind to actin, and observed that the transition from G-actin to F-actin was accompanied by a strong intensity increase form the molecular rotor reporter. Lindgren et al. [36] examined the folding kinetics of transthyretin, a protein known to misfold and form amyloid deposits in peripheral nerves. The authors found that the molecular rotors DCVJ and thioflavin T preferentially bind to misfolded transthyretin and allow to specifically monitor the formation dynamics of pathogenic transthyretin aggregates.
The characterization of cyclodextrins is another representative area where the ability of molecular rotors to report the properties of the microenvironment plays a key role [37, 38]. Cyclodextrins have a hydrophobic core that can be used to deliver hydrophobic compounds to aqueous environments (e.g., drug delivery) [39]. To optimize cyclodextrins for a particular purpose, the nature of the core region needs to be explored. Dual-emission molecular rotors, such as DMABN, are ideally suited for this task, because emission from the twisted state reports hydrophobicity, whereas emission from the planar state reports on the restricted environment of the core.
Another area where molecular rotors found widespread application is the examination 5 of phospholipid bilayers and cell membranes [40–43]. Lukac [44], for example, examined several phospholipids that were stained with molecular rotor reporters under varying temperature conditions and found a change in the temperature-dependent behavior: When the phospholipid transitioned from the gel- to the liquid-crystal phase, a blue-shift of the emission was observed when the rotor molecules moved towards the more hydrophobic center of the bilayer as the bilayer "melted" at higher temperature. Moreover, Lukac was able to deduce an apparent bilayer microviscosity for the individual phospholipids. Following the same line of investigation, Nipper et al. [45] demonstrated that microviscosity, determined through molecular rotor fluorescence, correlates highly with the viscosity determined through fluorescence recovery after photobleaching (FRAP). FRAP is a microscopy method where fluorophore diffusivity in a phospholipid membrane can be determined, thus allowing to estimate microviscosity.
Whereas many fluorescent probes in biology predominantly offer qualitative information, the promise of molecular rotor fluorescence is the quantitative nature of the fluorescent response. In fact, fluorescence emission of molecular rotors can be used to determine the microviscosity of the environment with the same level of rigor as two established methods, FRAP [46] and fluorescence anisotropy [47]. All three methods are based on diffusion. FRAP is governed by lateral diffusion of a fluorophore into a region where the dye has been destroyed by intense light. Fluorescence anisotropy is governed by the rotational diffusion of a dye that has been excited by polarized light, where rotational diffusion leads to depolarization of the emission light. Rotational diffusion governs the propensity of a molecular rotor to form twisted states and therefore relates diffusivity to fluorescence quantum yield. In this respect, molecular rotors report diffusivity similar to anisotropy probes. However, the dominating factor in molecular rotor emission is the rotation of one segment relative to the other. The segment (such as the dimethylamino group or the dicyanovinyl segment) is generally very small and enjoys greater freedom of rotation than a typical anisotropy probe, such as 1,6-diphenyl-1,3,5-hexatriene (DPH). The relationship between viscosity, rotational diffusivity, and intramolecular rotation makes molecular rotors attractive reporters for the microenvironment, because the sensing of the diffusivity - and with it, microviscosity - can be reduced to simple and rapid spectroscopic intensity measurements [16].
Photophysical Principles of Molecular Rotors
A fluorescent intramolecular charge-transfer (ICT) complex is elevated to a higher energy level after photoabsorption by charge separation, that is, an electron is transferred from the donor unit to the acceptor unit. With reference to Figure 1A, the molecule assumes the excited-state configuration D+ - π - A-. The charge separation is associated with an increased dipole moment. In the example of DMABN, the ground-state dipole moment is approximately 6 Debye (1 Debye [D] ≈ 3.336·10-23C·m), and the excited-state dipole moments have been found to be approximately 10 Debye in the planar conformation and between 19 and 22 Debye, depending on the solvent, in the TICT (twisted intramolecular charge transfer) conformation [48]. Polar solvent molecules orient themselves along the fluorophore dipole by aligning their electric fields. Upon relaxation, the solvent molecules return to the ground-state orientation. As a consequence, the fluorophore exhibits a bathochromic shift that reflects the energy expended for the reorientation of the solvent molecules. The magnitude of this effect depends on the solvent polarity, that is, its dielectric constant [49]. Molecular rotors typically exhibit stronger solvatochromism in the twisted-state emission band than in the planar locally excited (LE) emission band. Furthermore, both the ground-state and the excited-state energy levels depend on the degree of intramolecular rotation [50–52]. The Jabłonski diagram of the energy states can be extended to include the TICT-state energy levels (Figure 2). In the ground state, a planar conformation is energetically preferred, whereas the twisted conformation is the preferred conformation in the excited state. Therefore, the excited molecule rapidly assumes the twisted-state conformation. Viscous solvents are known to increase the energy barrier between the LE and TICT states (indicated by a dashed line in Figure 2), and emission shifts in favor of the LE band. Figure 2 does not include triplet states, because intersystem crossing plays a negligible role in the spectral emission of molecular rotors. The TICT formation rate emerges as the dominant factor that determines the relative intensity of the two emission bands in the case of molecular rotors with dual emission and the overall quantum yield in the case of molecular rotors with radiationless relaxation from the TICT state.
Extended Jabłonski diagram for molecular rotors. Like conventional fluorophores, a molecular rotor is elevated from the ground state (S0) to the energetically higher first excited state (S1) by photon absorption. Different vibrational states (indicated by parallel lines) cause some energy loss, and emission from the LE state occurs at a longer wavelength than the excitation (Stokes shift). For molecular rotors, the Jabłonski diagram needs to be extended, because the excited-state energy is lower in the TICT state, whereas the ground-state energy is higher in the TICT state than in the LE state. Therefore, the S1 - S0 energy gap is lower in the TICT state with a correspondingly lower relaxation energy. In the case of moelcular rotors with dual-band emission (such as DMABN), the TICT energy gap is slightly smaller than the LE energy gap (A). If the TICT energy gap is much smaller than the LE energy gap, for example in DCVJ, emission from the TICT state occurs without photon emission (B). This diagram does not reflect intersystem crossing, because triplet states do not play any significant role in the fluorescence of molecular rotors.
Interactions of Molecular Rotors with the Environment
The solvent directly influences the TICT formation rate. Polar solvents are known to stabilize the TICT state [48] and thus increase relaxation from the TICT state. The polarity of molecules is associated with the ability to form hydrogen bonds, and hydrogen bond formation between molecular rotors and the solvent has been found to increase TICT formation rate [53]. With respect to the applications that were presented earlier, the most important rotor-solvent interaction is the sensitivity towards the solvent's viscosity. In viscosity-sensing applications, molecular rotors with a single emission band are most widely used, because emission from the LE state is relatively insensitive towards the solvent polarity [4, 34, 41]. LE-state quantum yield ϕ F and bulk viscosity η follow a power-law relationship that is widely referred to as the Förster-Hoffmann equation,
where C and x are solvent- and dye-dependent constants. This relationship has been experimentally shown to be valid in a wide range of viscosities and in both polar and nonpolar fluids [15, 34, 40, 54, 55], although deviations exist particularly in the low-viscosity regime that need additional interpretation. Equation 1 has become so popular that in some instances the existence of this power-law relationship has been used to purport TICT behavior of specific molecules [56–59].
Equation 1 holds the prisomise of a quantitative relationship between viscosity and quantum yield. Steady-state emission intensity is proportional to the quantum yield, and the excited-state lifetime τ is related to the quantum yield through
where τ0 is the natural lifetime of the fluorophore. To understand the relationship in Equation 1 and the significance of the constants C and x, it is necessary to closely examine the relationship between bulk viscosity, molecular-scale interaction of the molecular rotor with the solvent, and the fluorescence quantum yield.
Quantitative Influence of Diffusion on Tict Behavior
Currently accepted theories of rotor-solvent interaction center on diffusion. Two derivations of Equation 1 are based on Debye-Stokes-Einstein diffusion and free-volume diffusion, respectively. Förster and Hoffmann [9] provided a rigorous derivation based on classical mechanics and the assumption of Debye-Stokes-Einstein (DSE) diffusion. In their ground-breaking work on triphenylamine dyes, Förster and Hoffmann postulated that each aniline group acts as a nanoscale ellipsoid that obeys the second-order differential equation of rotational motion,
where φ is the rotational angle of the aniline group with respect to the ground-state equilibrium position φ0, θ is the rotational inertia of the aniline group, and α reflects the electrostatic force that returns the aniline group to its equilibrium position. The microfriction κ is linked to bulk viscosity η through the DSE diffusion model,
where r is the effective radius of the aniline group. Under the assumption of strong damping (more precisely, κ2 ≫ 4κθ), a twisted aniline group returns to the ground-state equilibrium in an exponential-decay fashion with a decay constant of κ/α. Förster and Hoffmann define a function B(φ) as B(φ) = β(φ-φ0)2 that describes the rate of deactivation processes through conformational changes, with β being a proportionality constant. With this definition, a differential equation can be found that governs the probability ρ(t) that the molecule is in the excited state:
Here, δ is the angular difference between the lowest-energy conformations in the excited and ground states and τ s is the lifetime of the fluorophore in the absence of rotational relaxation events. The quantum yield ϕ F can be obtained by integrating the excited-state probability:
Although not defined in the original manuscript [9], τ0 can be assumed to be the natural lifetime, that is, the lifetime of the fluorophore in the absence of any nonradiative deactivation processes as opposed to τ s , which is the lifetime in the absence of only rotational deactivation processes. According to Förster and Hoffmann, typically τ s /τ0 ≈ 0.5 for this class of molecular rotors [9]. To simplify the solution of Equation 5 and its subsequent integration (Equation 6), Förster and Hoffmann examined three special cases. The first case (Equation 7) emerges for low viscosities where the quantum yield reaches a solvent-independent minimum:
The second case occurs in solvents of very high viscosity, where radiative relaxation dominates with negligible rotational relaxation, and the quantum yield can be approximated by Equation 8:
In Equation 8, σ is a dye-dependent constant that contains all viscosity-independent variables and has units of viscosity:
The most important case, the third case, is found for intermediate viscosities η ≪ σ, when the solution of Equation 6 simplifies to Equation 10:
For crystal violet, a triphenylmethane dye, σ ≈ 100 Pa s can be found. The remaining constants can be combined into one constant , yielding Equation 11, which is the non-logarithmic form of Equation 1 with an exponent x ≡ 2/3 as the result of an integration step:
Other quantitative treatments of the viscosity-sensitive behavior are based on the premise that the intramolecular reorientation rate k or depends on rotational diffusivity, more precisely, k or ∝ D. A fluorophore's quantum yield ϕ F is defined as the radiative relaxation rate k R relative to the total relaxation rate k R + k NR (Equation 12):
The approximation is valid for molecular rotors, because the intramolecular reorientation rate k or is the dominant nonradiative relaxation pathway, and k or ≫ k R . Furthermore, k R is a viscosity-independent dye constant. DSE diffusion stipulates that the rotational diffusion constant D is inversely proportional to viscosity (Equation 13):
Here, V is the effective volume of the molecule, s reflects a boundary condition (s = 1 for a stick condition and s < 1 for a slip condition), g is a shape factor, k B is Boltzmann's constant, and T is the temperature. Vogel and Rettig [60] define a driving force F , which is the force constant of the harmonic twist potential in triphenylmethane dyes, such that
where ζ S is the Stokes friction coefficient, defined as ζ S = 6V η, implicitly setting s = 1 and g = 1. Vogel and Rettig now argue that the product of viscosity and rotational reorientation rate would be constant under the DSE theory (Equation 15) [60].
Experimental evidence invalidates Equation 15, because the product k or η increases strongly with decreasing temperature. To explain the deviation from DSE theory, Vogel and Rettig use the microfriction model introduced by Gierer and Wirtz [61]. These authors extend DSE theory by accounting for the finite thickness of molecular layers that surround the fluorophore. By solving the equation of rotational motion for a spherical molecule of radius r M surrounded by finite layers of spherical solvent molecules with a radius r S , Gierer and Wirtz obtain a corrected microfriction coefficient ζ Micro that is related to the DSE macrofriction coefficient ζ Macro through Equation 16 [61]:
Vogel and Rettig interpret this result as a superposition of Stokes diffusional freedom 1/ζ S and free-volume diffusional freedom 1/ζ FV (Equation 17), where diffusion is facilitated by void spaces between solvent and solute.
Viscosity decreases with increasing temperature. A commonly-used model is the Arrhenius function
where η0 is a material constant, E A is an apparent activation energy, k B is Boltzmann's constant, and T is the absolute temperature. Since viscosity is assumed to be proportional to the friction coefficient ζ, the apparent microviscosity η Micro of the solvent, which is reported by the molecular rotor, would be smaller than the DSE macroviscosity. More specifically, the apparent microviscosity can be described as the superposition of two Arrhenius terms (Equation 19),
where a and b are related to the material constant η0, and E η and E FV are the apparent activation energies for DSE macroviscosity and the free-volume viscosity term, respectively. After some arithmetic manipulation, Vogel and Rettig arrive at an extension of Equation 15, namely, k or η = A + B ηx , where A corresponds to the term F/3V in Equation 15 and x reflects the relative contribution from Stokes and free-volume diffusion and is not identical to the exponent x in Equation 1. With A and B being experimental constants, this model was found to represent a good fit of experimental data [60]. To obtain an equation similar to Equation 11, k or can be substituted in Equation 12, leading to Equation 20, which is an alternative model to Equation 1:
Free volume was also recognized as an important determinant of a molecular rotor's quantum yield by Loutfy and coworkers [62–64]. The treatment by Loutfy et al. is based on Doolittle's [65] empirical relationship between viscosity and free volume, Equation 21,
where A and B are empirical, solvent-dependent constants with B ≈ 1, v o is the occupied volume, and v f is the free volume. The free volume is the temperature-dependent factor, and for glass-forming liquids, the free volume reaches a minimum at the glass transition temperature [66]. The ratio v f /v o is the relative free space for a liquid and becomes very small, typically 0.025, at the glass transition of many alcohols. Loutfy and Arnold [63] provide experimental evidence that the quantum yield of a fluorophore follows a relationship analogous to Equation 21,
where kNR,0is interpreted as an intrinsic, fluorophore-dependent constant, and x is the slope found in plots of logϕ F over . Equation 22 allows to express the rotational relaxation rate as a function of free volume, namely, k or = kNR,0exp(-x v v /v f ). Contrary to the assumptions by Vogel and Rettig and by Förster and Hoffmann, Loutfy and Arnold found 15 a power-law relationship between viscosity and diffusional reorientation rate. Equation 21 can be used to replace the free-volume term by viscosity, which yields Equation 23:
By combining the dye- and solvent-dependent constants k R , kN R,0, and Ax into one constant C, Equation 1 readily emerges. It is noteworthy that the rigorous derivation by Förster and Hoffmann - under the assumption of rotational friction according to the DSE model - and the more empirical derivation by Loutfy and Arnold - under the assumption of a power-law microfriction behavior - lead to the same relationship between quantum yield and bulk viscosity. Contrary to the Förster- Hoffmann derivation, however, the exponent x in Equation 23 can vary with the solvent and the molecular rotor molecule.
In practice, each of the models has limited applicability. A comparison of the model by Vogel and Rettig to the model by Loutfy et al. is shown in Figure 3. Each data point represents solvent viscosity and measured intensity of the molecular rotor DCVJ at a concentration of 5 μ M. Intensity is proportional to quantum yield, and an additional proportionality constant needs to be introduced in Equations 1 and 20 to reflect concentration and instrument constants. It can be seen that Equation 1 describes the data from polar solvents well in accordance with the literature [15, 34, 40, 54]. Equation 20 describes the data almost equally well, although Equation 1 is statistically the preferred model (F-test, P = 0.89). The model in Equation 20 tends to underestimate the viscosity at very low and very high solvent viscosities. In fact, when A ≪ B, Equation 20 takes up the form of Equation 1. The curve fit in Figure 3 provided A ≈ B/10. However, this ratio is not in agreement with values reported by Vogel and Rettig, where A and B are in the same order of magnitude. In this example, high viscosities were achieved with a viscosity gradient of mixtures of glycerol and a low-viscosity alcohol, such as ethylene glycol or methanol. This method is commonly used in the literature [33, 40, 54, 56, 63, 67] to achieve large-scale variations in viscosity with relatively small variations in polarity.
Comparison of the models for the quantum yield - viscosity relationship. Shown is the peak emission intensity of 5 μ M DCVJ in various solvents. Black squares indicate polar, protic solvents (single- and polyfunctional alcohols); green circles indicate dipolar, aprotic solvents, and brown squares indicate nonpolar solvents. Equations 1 and 20 have been fitted to the intensity/viscosity data of the polar solvents (black squares) with the exception of water (open square). The gray region indicates a viscosity gradient made of mixtures of ethylene glycol and glycerol. Equation 1 creates a straight line (blue) in the double-logarithmic plot with a slope of x = 0.45, whereas Equation 20 (red) curves and drops below Equation 1 for large and small η. It can be seen that polarity effects dominate at low viscosities. The light-blue dotted line indicates qualitatively a deviation reported by Law [15] in long-chained 1-alkanols.
Deviations from the model can be seen in several instances. Water with its very high polarity reduces the barrier to the TICT state [50] and causes an anomalous low fluorescence. Polar aprotic solvents, such as dimethylsulfoxide, dimethylformamide, and acetone show a higher DCVJ intensity than predicted by the models, and nonpolar solvents (methylene chloride, benzene and toluene) have an even higher intensity, because nonpolar solvents stabilize the LE state. It can be seen that at low viscosities, other effects than microfriction dominate. Law [15] has reported that the chain length of short-chain 1-alkanols has a very small effect on the quantum yield, which would corroborate the low viscosity case presented by Förster and Hoffmann (Equation 7). According to Law [15], long-chain 1-alkanols also deviate from the models (light blue dotted line in Figure 3), because the alkane chain becomes the main determinant of intramolecular rotation, and the viscosity of alkanes is known to be much lower than that of the corresponding 1-alkanols.
In summary, rotational diffusivity is the most important determinant of intramolecular rotation rate and therefore a molecular rotor's quantum yield. However, when the intramolecular rotation rate becomes very high in solvents of low viscosity, additional effects, such as hydrogen bond formation, excimer formation, and polar-polar interaction are no longer negligible and cause significant deviations from established models that describe the relationship between quantum yield and viscosity.
Engineering Aspects of Molecular Viscometers
There is a growing need for viscosity reporters with microscopic resolution and ultrafast response. Due to the nature of the twisted-state formation, which takes place within tens of picoseconds [68], a molecular rotor reports changes in the local microviscosity almost instantaneously. Since molecular rotors are affected only by their immediate microenvironment, they can be used to report spatially resolved microviscosity with resolution limited only by the optical equipment. These two features explain the popularity of molecular rotors in cell and vesicle research [40, 43–45, 69–73]. Furthermore, molecular rotors enjoy high popularity as real-time probes of polymerization processes [62, 74, 75], where one reason is the poor suitability of conventional methods due to their invasive nature and associated destructiveness, and their poor accuracy [76]. Conversely, molecular rotors allow in situ probing. Other potential areas of application are food science, for example, the crystallization behavior of lactose [77] or the behavior of soy flour according to the Williams-Landel-Ferry model [78], and the measurement of bulk viscosity of biofluids, where short measurement and turnaround times may accelerate serial viscosity measurement by orders of magnitude [26]. The key to these applications is the potential of a quantitatively accurate measurement.
Steady-State Spectroscopy and Intensity Measurements
Emission intensity I EM and quantum yield ϕ F are proportional. Therefore, steady-state fluorescence spectroscopy can be calibrated to provide quantum yield from peak spectral intensity. In any steady-state instrument, Equation 24 holds for low dye concentrations:
Here, G is the instrument gain factor, c is the dye concentration, and I EM is the emission light intensity. If ϕ F is substituted with Equation 1, these factors are combined together with the dye-dependent constant C, into one calibration constant that can be determined with reference fluids. This calibration process is comparable to that of mechanical rheometers, although the exponent x plays an important role and needs to be determined beforehand for each specific class of fluids, such as alcohols, aqueous solutions, or oils. If the proportionality factors in Equation 24 are known, they can be combined into a single calibration constant ξ, and the equation can be solved for η:
With this method the precision of mechanical rheometers can be reached or exceeded [26]. However, intensity measurements can be confounded if the solvent is absorbent (colored) or scattering. Spectrofluorometers exist that can simultaneously measure fluorescence emission and spectral absorption. In practice, it is difficult to distinguish dye absorption from fluid absorption, but dye concentration and its absorption coefficient are usually known. In this case, it is possible to correct the measured intensity and obtain a value that represents the idealized intensity in the absence of fluid absorption. The fraction of excitation light I A that passes through the sample can be described by Beer's law as I A = I0exp(-ϵcl) where ϵ is the dye extinction coefficient and l is the length of the light path though the sample. The difference between the incident light I0 and the exiting light I A is available for dye excitation. Measurement of I A allows to calculate one unknown coefficient, either c or l. The corrected I EX can be used in Equation 24. Although this method can be used to reduce the influence of variations in dye concentration in a clear fluid, its practical relevance becomes much higher in absorbing or scattering fluids [28]. Examples are blood plasma and lymphatic fluid, which preferentially absorb blue light and solutions of macromolecules, which often exhibit Rayleigh scattering. If a solvent has an absorption coefficient μ A , less light is available for photoexcitation, and I EX can be approximated with Equation 26:
Again, absorption measurement can provide the unknown μ A , and when the dye concentration is known, a corrected excitation intensity can be computed for Equation 24. A spectrophotometer that measures fluorescence, scattering, and absorbance simultaneously can be designed with relatively few, low-cost components. One possible design is shown in Figure 4. A single light source provides excitation light for the sample. Absorbance is measured with a photodiode, and both scattering and fluorescence intensity are measured with a photomultiplier through a monochromator.
Proposed spectrophotometer with the capability to measure fluorescence intensity, absorbance, and scattering simultaneously. The excitation light source L can be a laser, a highly collimated light-emitting diode (LED), or a broadband source with selectable excitation filters. Excitation light is directed onto the sample S. Light that is not absorbed by the sample reaches the photodetector PD1, which can be a photodiode or a photomultiplier tube. The measurement of absorbed light against a blank sample provides total sample absorbance. Fluorescence emission is collected in a monochromator MC and can be spectrally resolved and analyzed in the second detector PD2, which needs to be a photomultiplier tube. Single-wavelength measurements are possible by using filters instead of a monochromator. Fluorescence collection uses the conventional L geometry, because the smallest amount of scattered light is found perpendicular to the excitation beam. However, a scattering sample causes a measurable amount of excitation light to be scattered into the monochromator, and by selecting the excitation wavelength, the amount of scattering can be determined. This device is similar to the one presented by Milich et al. [28].
Correction for fluid optical properties becomes even more complex when the dye concentration is high and when the solvent absorption is strongly wavelength-dependent. The presence of scatterers further complicates the correction. In two relatively simple cases of forward-scattering microspheres and of starch solutions, the average excitation path length was found to be increased, and the presence of the scatterer increased fluorescence intensity. By measuring the scattering intensity, a corrected fluorescence emission was found that almost completely eliminated the influence of the scattering agent [28]. Higher scatterer content, however, would again reduce the measured intensity, and additional studies need to be performed to obtain correction formulas or algorithms for different types and concentrations of scatterers, and for combinations of scatterers and absorbers.
Time-Resolved Spectroscopy
Time-resolved spectroscopy promises to overcome some of the challenges associated with steady-state measurements. Most important, quantum yield and lifetime τ are directly related without the proportionality factors seen in Equation 24. When the natural lifetime τ0 - the largest possible lifetime for a fluorphore - is known, for example from a measurement in supercooled glass, the quantum yield can be computed as ϕ F = τ/τ0. The resulting quantum yield can be used directly in Equation 1, which leads to the lifetime equation analogous to Equation 25:
Natural lifetimes for some molecular rotors have been found to be between 3 ns and 4 ns [15, 64], and actual lifetimes can be in the low picosecond range for low-viscosity solvents [64]. To accurately measure such short lifetimes, relatively sophisticated instruments are required, which can be very expensive compared to simple steady-state instruments.
Moreover, lifetime measurements may reveal multiexponential decay behavior. Vogel and Rettig [15] found double-exponential decays in triphenylmethane dyes and attributed the two decay components to DSE and free-volume diffusion, respectively. Law [15] reported that solvent diffusional rotation causes shorter measured lifetimes. Multiexponential relaxation dynamics that were dominated by solvent relaxation constants were also found by Dutta and Bhattacharyya [79], who reported lifetime constants in the low picosecond range and in the low nanosecond range, whereby the nanosecond range carried significant information about the type of solvent. Hara et al. [80] found triple-exponential decay functions when they applied pressure to the solvents to cause a pressure-induced viscosity increase. The analysis of lifetime experiments is complex, because many levels of solvent-rotor interaction, such as diffusion, electrostatic and polar interaction, and hydrogen bonding influence the lifetime dynamics and lead to complex decay patterns. This level of complexity cannot be seen in steady-state experiments. Whereas steady-state measurements can be confounded by solvent- and instrument-related factors, lifetime experiments are affected by the complex rotor-solvent interaction. More research is needed to separate and interpret the lifetime components and find an accurate relationship to the solvent's microviscosity.
On the other hand, spatially-resolved lifetime measurement, for example, fluorescence lifetime imaging microscopy (FLIM) [81] is a promising method, and in many cases a simplified lifetime-viscosity relationship (Equation 27) is sufficiently accurate for physiological studies. The major advantage of FLIM over steady-state fluorescence microscopy is its in-dependence from local dye concentration gradients, which makes FLIM an ideal method for studies in living cells [56, 57]. With the exception of very expensive and advanced devices, FLIM is limited to single-exponential decays [81], and the complexity of the decay dynamics described in the previous section is difficult to reproduce.
Ratiometric Measurements and Self-Calibrating Dyes
A third approach to reduce the influence of local concentration gradients and some sample optical properties (absorption, scattering) are engineered ratiometric dye systems [82]. It is possible to covalently couple a molecular rotor to a reference fluorophore that is not viscosity-sensitive (Figure 5). The two covalently linked fluorophores exhibit three distinct emission peaks as shown in Figure 6: direct emission from the reference fluorophore, direct emission form the molecular rotor, and indirect emission from the molecular rotor, where excited-state energy is transferred from the reference fluorophore through resonance energy transfer (RET). Since the two units are covalently linked, their local concentration is always identical. Therefore, the instrument-dependent constants G and I EX and the concentration c cancel out in Equation 24 when the ratio of rotor emission to reference emission is used. The emission light of both fluorophores also experiences the same absorption and scattering. The ratiometric method offers similar advantages as lifetime measurement, albeit with relatively low-cost steady-state equipment. One limitation occurs when fluid absorption and scattering become wavelength-dependent, in which case reference and rotor intensity need to undergo additional correction steps. Moreover, fluorescence intensity from RET is inherently less efficient than direct excitation. Particularly in low-viscosity cases, this method may suffer from a poor signal-to-background ratio in absorbing or scattering media. However, the spectra in Figure 6B demonstrate that intensity from RET is only about a factor 2 lower than direct intensity, which should be sufficient for most applications.
Basic structure of an engineered ratiometric dye system (A). A conventional fluorescent molecule that is not viscosity-sensitive serves as intensity reference (Ref) and is coupled to a molecular rotor through a linker structure. The fluorescent groups can be excited individually and emit fluorescence at their typical wavelength. However, when the reference unit is excited, it transfers some of its excited-state energy to the rotor via resonance energy transfer (RET), and dual emission from both reference and rotor can be observed. One possible chemical structure is shown in B. The reference is a coumarin (blue), and the rotor is a structure is based on an aniline motif rather than the tricyclic julolidine found in DCVJ.
Emission profile of the ratiometric dye system in Figure 5. The fluorescence fingerprint (A) shows the emission intensity as a function of both excitation and emission wavelength. Three distinct emission peaks emerge. The first is caused by the reference fluorophore (Ref), the second by the molecular rotor where the excitation of the rotor molecule takes place through resonance energy transfer from the reference (RET), and the third is emitted from the rotor after direct excitation of the rotor (ROTOR). B shows the emission maxima in solvents of different viscosity. It can be seen that the reference emission is widely independent of the viscosity, and small variations can be attributed to refractive index changes. Conversely, rotor emission increases with viscosity in a power-law fashion, irrespective of whether the rotor is excited directly or through RET.
Conclusion
Molecular rotors are a twisted-state-forming subgroup of intramolecular charge transfer fluorophores. The twisted-state formation rate is strongly dependent on the environment, most dominantly on the local diffusion coefficient. Two overarching groups of these fluorophores are those where relaxation from both LE and twisted states are associated with photon emission, and those where relaxation from the twisted state occurs radiationless. The former show a dual- band emission with a strong polarity-dependent solvatochromic shift and very strong dependency of the twisted-state emission band (the red-shifted band) on both polarity and viscosity of the medium. The latter show single-band emission from the LE state with a highly viscosity-dependent quantum yield. The viscosity-dependent emission is hypothesized to be related to rotational diffusion, although different theoretical treatments of the viscosity-dependence exist. Apart from viscosity, solvent polarity, hydrogen bond formation and excimer formation also play a role in the spectroscopic properties of molecular rotors. These complex interactions with the environment provide one impediment to using molecular rotors as fluorescent microrheometers. However, at viscosities above 2 mPa s, steric hindrance dominates twisted-state formation, and viscosity becomes the singularly most dominant factor to influence the molecular rotor's quantum yield. A power- law relationship between quantum yield and viscosity is most widely used, and this relationship is confirmed by experimental observation over more than three orders of magnitude of solvent viscosity. With molecular rotors, viscosity measurement can be reduced to either intensity measurements or fluorescent lifetime measurements. A particular strength of the fluorescent method lies in the ability to spatially resolve the emission (fluorescent imaging) with applications in biology, cell physiology and polymer chemistry. However, there are confounding factors that deserve further research. First, the optical properties of the microenvironment can influence the emission signal, and the emission needs to be corrected for absorption and scattering to obtain accurate microviscosity information. Second, the constants in the power-law relationship between quantum yield and viscosity require calibration for each fluid type. Most notably, the exponent × was found to be a constant of x = 2/3 by Förster and Hoffmann, but can be variable according to the free-volume theory by Loutfy et al. Further research into the rotor-solvent interaction will likely illuminate the constants used in the relationship between quantum yield and viscosity and therefore increase the accuracy with which the microvisocsity can be measured with molecular rotors.
Acknowledgements
The authors gratefully acknowledge research support from the National Institutes of Health through NIH grant 1R21 RR 025358.
References
Beens H, Weller A: Excited molecular n -complexes in solution. In Organic molecular photophysics. Edited by: Birks JW. Wiley, New York; 1975.
Grabowski ZR, Rotkiewicz K, Rettig W: Structural Changes Accompanying Intramolecular Electron Transfer: Focuson Twisted Intramolecular Charge-Transfer States and Structures. Chem Rev 2003,103(10):3899-4031. 10.1021/cr940745l
Rettig W: Application of a simplified microstructural solvent interaction model to the solvatochromism of twisted intramolecular charge transfer (TICT) states. J Mol Struct 1982,84(3-4):303-327. 10.1016/0022-2860(82)85263-0
Allen BD, Benniston AC, Harriman A, Rostron SA, Yu C: The photophysical properties of a julolidene-based molecular rotor. Physical Chemistry Chemical Physics 2005,7(16):3035-3040. 10.1039/b507165h
Haidekker MA, Nipper ME, Mustafic A, Lichlyter D, Dakanali M, Theodorakis EA: Dyes with segmental mobility: molecular rotors. In Advanced Fluorescence Reporters in Chemistry and Biology I. Edited by: Demchenko A. New York: Springer; 2010:in press. [Wolfbeis O (Series Editor): Springer series in fluorescence, vol. 8]
Atsbeha T, Mohammed AM, Redi-Abshiro M: Excitation Wavelength Dependence of Dual Fluorescence of DMABN in Polar Solvents. Journal of Fluorescence 2010, in press.
Haidekker MA, Ling T, Anglo M, Stevens HY, Frangos JA, Theodorakis EA: New fluorescent probes for the measurement of cell membrane viscosity. Chemistry & biology 2001,8(2):123-131.
Ramadass R, Bereiter-Hahn J: Photophysical properties of DASPMI as revealed by spectrally resolved fluorescence decays. J Phys Chem B 2007,111(26):7681-7690. 10.1021/jp070378k
Förster T, Hoffmann G: Die Viskositatsabhängigkeit der Fluoreszenzquantenausbeuten einiger Farbstoffsysteme [Effect of viscosity on the fluorescence quantum yield of some dye systems]. Z Phys Chem 1971, 75: 63-76.
Dutta AK, Kamada K, Ohta K: Spectroscopic studies of Nile red in organic solvents and polymers. Journal of Photochemistry & Photobiology, A: Chemistry 1996, 93: 57-64.
Golini CM, Williams BW, Foresman JB: Further solvatochromic, thermochromic, and theoretical studies on Nile Red. Journal of Fluorescence 1998,8(4):395-404. 10.1023/A:1020584801600
Kosower EM: Intramolecular donor-acceptor systems. 9. Photophysics of (phenylamino) naphthalenesulfonates: a paradigm for excited-state intramolecular charge transfer. Accounts of Chemical Research 1982,15(8):259-266. 10.1021/ar00080a005
Kee HL, Kirmaier C, Yu L, Thamyongkit P, Youngblood WJ, Calder ME, Ramos L, Noll BC, Bocian DF, Scheidt WR: Structural control of the photodynamics of borondipyrrin complexes. The journal of physical chemistry B 2005,109(43):20433. 10.1021/jp0525078
Rotkiewicz K, Grellmann KH, Grabowski ZR: Reinterpretation of the anomalous fluorescence of pN, N-dimethylaminobenzonitrile. Chem Phys Lett 1973, 19: 315-318. 10.1016/0009-2614(73)80367-7
Law KY: Fluorescence Probe for Microenvironments: Anomalous Viscosity Dependence of the Fluorescence Quantum Yield of P-N, N Dialkylaminobenzylidenmalononitrile in 1-Alkanols. Chem Phys Lett 1980,75(3):545-549. 10.1016/0009-2614(80)80574-4
Haidekker MA, Theodorakis EA: Molecular rotors -fluorescent biosensors for viscosity and flow. Organic & Biomolecular Chemistry 2007,5(11):1669-1678.
Harkness J: The viscosity of human blood plasma; its measurement in health and disease. Biorheology 1971,8(3):171.
Letcher RL, Chien S, Pickering TG, Sealey JE, Laragh JH: Direct relationship between blood pressure and blood viscosity in normal and hypertensive subjects:: Role of fibrinogen and concentration. The American Journal of Medicine 1981,70(6):1195-1202. 10.1016/0002-9343(81)90827-5
McMillan DE: Further observations on serum viscosity changes in diabetes mellitus. Metabolism 1982,31(3):274-278. 10.1016/0026-0495(82)90064-6
Otto C, Ritter MM, Richter WO, Minkenberg R, Schwandt P: Hemorrheologic abnormalities in defined primary dyslipoproteinemias with both high and low atherosclerotic risks. Metabolism 2001,50(2):166-170. 10.1053/meta.2001.20192
Roe PF, Harkness J: Plasma viscosity in the elderly. Gerontology 1975,17(3):168-172.
Ernst E, Matria A, Schmölzl C, Magyarosy I: Dose-effect relationship between smoking and blood rheology. British journal of haematology 1987,65(4):485-487. 10.1111/j.1365-2141.1987.tb04155.x
Bates DO, Levick JR, Mortimer PS: Change in macromolecular composition of interstitial fluid from swollen arms after breast cancer treatment, and its implications. Clinical science (London, England: 1979) 1993,85(6):737.
Martin GS, Lewis CA: Fluid management in shock. In Seminars in Respiratory and Critical Care Medicine. Volume 25. New York: Thieme Medical Publishers; 1994:683-693. 10.1055/s-2004-860982
Haidekker MA, Tsai AG, Brady T, Stevens HY, Frangos JA, Theodorakis E, Intaglietta M: A novel approach to blood plasma viscosity measurement using fluorescent molecular rotors. American Journal of Physiology 2002,282(5):H1609-H1614.
Akers WJ, Haidekker MA: Precision assessment of biofluid viscosity measurements using molecular rotors. Journal of Biomechanical Engineering 2005, 127: 450. 10.1115/1.1894366
Rosencranz R, Bogen SA: Clinical laboratory measurement of serum, plasma, and blood viscosity. American journal of clinical pathology 2006, 125: S78.
Milich K, Akers W, Haidekker MA: A Ratiometric Fluorophotometer for Fluorescence-Based Viscosity Measurement with Molecular Rotors. Sensor Letters 2005,3(3):237-243. 10.1166/sl.2005.031
Loutfy RO, Teegarden DM: Effect of polymer chain tacticity on the fluorescence of molecular rotors. Macromolecules 1983,16(3):452-456. 10.1021/ma00237a022
Loutfy RO: Effect of polystyrene molecular weight on the fluorescence of molecular rotors. Macromolecules 1983,16(4):678-680. 10.1021/ma00238a035
Zhu D, Haidekker MA, Lee JS, Won YY, James CML: Application of Molecular Rotors to the Determination of the Molecular Weight Dependence of Viscosity in Polymer Melts. Macromolecules 2007,40(21):7730-7732. 10.1021/ma0702288
Hawe A, Filipe V, Jiskoot W: Fluorescent Molecular Rotors as Dyes to Characterize Polysorbate-Containing IgG Formulations. Pharmaceutical Research 2010,27(2):314-326. 10.1007/s11095-009-0020-2
Kung CE, Reed JK: Fluorescent molecular rotors: a new class of probes for tubulin structure and assembly. Biochemistry 1989,28(16):6678-6686. 10.1021/bi00442a022
Haidekker MA, Brady TP, Lichlyter D, Theodorakis EA: Effects of solvent polarity and solvent viscosity on the fluorescent properties of molecular rotors and related probes. Bioorganic Chemistry 2005,33(6):415-425. 10.1016/j.bioorg.2005.07.005
Sawada S, Iio T, Hayashi Y, Takahashi S: Fluorescent rotors and their applications to the study of GF transformation of Actin. Analytical biochemistry 1992, 204: 110-117. 10.1016/0003-2697(92)90148-Z
Lindgren M, Sörgjerd K, Hammarström P: Detection and characterization of aggregates, prefibrillar amyloidogenic oligomers, and protofibrils using fluorescence spectroscopy. Biophysical journal 2005,88(6):4200-4212. 10.1529/biophysj.104.049700
Kim YH, Cho DW, Yoon M, Kim D: Observation of Hydrogen-Bonding Effects on Twisted Intramolecular Charge Transfer of p-(N, N-Diethylamino) benzoic Acid in Aqueous Cyclodextrin Solutions. J Phys Chem 1996,100(39):15670-15676. 10.1021/jp9613652
Al-Hassan KA, Khanfer MF: Fluorescence probes for cyclodextrin interiors. Journal of Fluorescence 1998,8(2):139-152. 10.1023/A:1022550409844
Albers E, Muller BW: Cyclodextrin derivatives in pharmaceutics. Crit Rev Ther Drug Carrier Syst 1995,12(4):311-337.
Haidekker MA, L'Heureux N, Frangos JA: Fluid shear stress increases membrane fluidity in endothelial cells: a study with DCVJ fluorescence. American Journal of Physiology- Heart and Circulatory Physiology 2000,278(4):H1401.
Kung CE, Reed JK: Microviscosity measurements of phospholipid bilayers using fluorescent dyes that undergo torsional relaxation. Biochemistry 1986,25(20):6114-6121. 10.1021/bi00368a042
Furuno T, Isoda R, Inagaki K, Iwaki T, Noji M, Nakanishi M: A fluorescent molecular rotor probes the kinetic process of degranulation of mast cells. Immunology letters 1992,33(3):285-288. 10.1016/0165-2478(92)90074-X
Viriot ML, Carré MC, Geoffroy-Chapotot C, Brembilla A, Muller S, Stoltz JF: Molecular rotors as fluorescent probes for biological studies. Clinical Hemorheology and Microcirculation 1998,19(2):151-160.
Lukac S: Thermally induced variations in polarity and microviscosity of phospholipids and surfactant vesicles monitored with a probe forming an intramolecular charge-transfer complex. Journal of the American Chemical Society 1984,106(16):4386-4392. 10.1021/ja00328a016
Nipper ME, Majd S, Mayer M, Lee JCM, Theodorakis EA, Haidekker MA: Characterization of changes in the viscosity of lipid membranes with the molecular rotor FCVJ. Biochimica et Biophysica Acta (BBA)-Biomembranes 2008,1778(4):1148-1153. 10.1016/j.bbamem.2008.01.005
Axelrod D, Koppel DE, Schlessinger J, Elson E, Webb WW: Mobility measurement by analysis of fluorescence photobleaching recovery kinetics. Biophysical Journal 1976,16(9):1055-1069. 10.1016/S0006-3495(76)85755-4
Shinitzky M, Yuli I: Lipid fluidity at the submacroscopic level: determination by fluorescence polarization. Chemistry and Physics of Lipids 1982,30(2-3):261-282. 10.1016/0009-3084(82)90054-8
Schuddeboom W, Jonker SA, Warman JM, Leinhos U, Kühnle W, Zachariasse KA: Excited-State Dipole Moments of Dual Fluorescent 4-(Dialkylamino) Benzonitriles. Influence of Alkyl Chain Length and Effective Solvent Polarity. J Phys Chem 1992, 96: 10809-10819. 10.1021/j100205a041
Ghoneim N, Suppan P: Solvation of TICT states in solvent mixtures. Pure and applied chemistry 1993, 65: 1739-1739. 10.1351/pac199365081739
Grabowski ZR, Dobkowski J: Twisted intramolecular charge transfer (tict) excited states: energy and molecular structure. Pure Appl Chem 1983, 55: 245. 10.1351/pac198855020245
Gregoire G, Dimicoli I, Mons M, donder Lardeux C, Jouvet C, Martrenchard S, Solgadi D: Femtosecond Dynamics of "TICT" State Formation in Small Clusters: The Dimethylaminobenzomethyl Ester Acetonitrile System. J Phys Chem A 1998,102(41):7896-7902. 10.1021/jp9818378
Rullière C, Grabowski ZR, Dobkowski J: Picosecond absorption spectra of carbonyl derivatives of dimethylaniline: the nature of the TICT excited states. Chemical Physics Letters 1987,137(5):408-413. 10.1016/0009-2614(87)80224-5
Guilbault GG: Practical fluorescence. CRC; 1990.
Iwaki T, Torigoe C, Noji M, Nakanishi M: Antibodies for fluorescent molecular rotors. Biochemistry 1993,32(29):7589-7592. 10.1021/bi00080a034
Wang K, Shi W, Jia J, Chen S, Ma H: Characterization of 2-phenylbenzo [g] quinoxaline derivatives as viscosity-sensitive fluorescent probes. Talanta 2009,77(5):1795-1799. 10.1016/j.talanta.2008.10.021
Kuimova MK, Yahioglu G, Levitt JA, Suhling K: Molecular rotor measures viscosity of live cells via fluorescence lifetime imaging. J Am Chem Soc 2008,130(21):6672-6673. 10.1021/ja800570d
Kuimova MK, Botchway SW, Parker AW, Balaz M, Collins HA, Anderson HL, Suhling K, Ogilby PR: Imaging intracellular viscosity of a single cell during photoinduced cell death. Nature Chemistry 2009, 1: 69-73. 10.1038/nchem.120
Levitt JA, Kuimova MK, Yahioglu G, Chung PH, Suhling K, Phillips D: Membrane-Bound Molecular Rotors Measure Viscosity in Live Cells via Fluorescence Lifetime Imaging. The Journal of Physical Chemistry C 2009, 113: 11634-11642. 10.1021/jp9013493
Wang D, Miyamoto R, Shiraishi Y, Hirai T: BODIPY-Conjugated Thermoresponsive Copolymer as a Fluorescent Thermometer Based on Polymer Microviscosity. Langmuir 2009,25(22):13176-13182. 10.1021/la901860x
Vogel M, Rettig W: Excited state dynamics of triphenylmethane-dyes used for investigation of microviscosity effects. Berichte der Bunsengesellschaft für Physikalische Chemie 1987,91(11):1241-1247.
Gierer Av, Wirtz K: Molekulare Theorie der Mikroreibung [Molecular theory of microfriction]. Zeitschrift für Naturforschung 1953, 8: 532-538.
Loutfy RO: Fluorescence probes for polymer free-volume. NATO ASI series. Series C, Mathematical and physical sciences 1986, 182: 429-448.
Loutfy RO, Arnold BA: Effect of viscosity and temperature on torsional relaxation of molecular rotors. The Journal of Physical Chemistry 1982,86(21):4205-4211. 10.1021/j100218a023
Loutfy RO, Law KY: Electrochemistry and Spectroscopy of Intramolecular Charge-Transfer Complexes.p -N,N-Dialkylamlnobenzylidenemalononitrlles. J Phys Chem 1980, 84: 2803-2808. 10.1021/j100458a027
Doolittle AK: Studies in Newtonian Flow. III. The Dependence of the Viscosity of Liquids on Molecular Weight and Free Space (in Homologous Series). Journal of Applied Physics 1952, 23: 236. 10.1063/1.1702182
Williams ML, Landel RF, Ferry JD: The temperature dependence of relaxation mechanisms in amorphous polymers and other glass-forming liquids. Journal of the American Chemical Society 1955,77(14):3701-3707. 10.1021/ja01619a008
Lang JM, Dreger ZA, Drickamer HG: A high pressure study of the effect of viscosity on the light induced isomerization of DMABN in three linear alcohols, iso-butanol and glycerol. Chemical Physics Letters 1995,243(1-2):78-84. 10.1016/0009-2614(95)00775-Y
Zachariasse KA, Grobys M, von der Haar T, Hebecker A, Il'ichev YV, Jiang YB, Morawski O, Knhnle W: Intramolecular charge transfer in the excited state. Kinetics and configurational changes. Journal of Photochemistry & Photobiology, A: Chemistry 1996,102(1S1):59-70.
Kuimova MK, Yahioglu G, Ogilby PR: Singlet Oxygen in a Cell: Spatially Dependent Lifetimes and Quenching Rate Constants. Journal of the American Chemical Society 2009, 131: 332-340. 10.1021/ja807484b
Kumar S, Singh AK, Krishnamoorthy G, Swaminathan R: Thioflavin T displays enhanced fluorescence selectively inside anionic micelles and mammalian cells. Journal of Fluorescence 2008,18(6):1199-1205. 10.1007/s10895-008-0378-2
White CR, Frangos JA: The shear stress of it all: the cell membrane and mechanochemical transduction. Philosophical Transactions B 2007,362(1484):1459. 10.1098/rstb.2007.2128
Mukherjee S, Raghuraman H, Chattopadhyay A: Membrane localization and dynamics of Nile Red: effect of cholesterol. BBA-Biomembranes 2007, 1768: 59-66. 10.1016/j.bbamem.2006.07.010
Haidekker MA, Brady T, Wen K, Okada C, Stevens HY, Snell JM, Frangos JA, Theodor-akis EA: Phospholipid-bound molecular rotors: synthesis and characterization. Bioorganic & medicinal chemistry 2002,10(11):3627-3636.
Haidekker MA, Lichlyter D, Johny MB, Grimes CA: Probing polymerization dynamics with fluorescent molecular rotors and magnetoelastic sensors. Sensor Letters 2006,4(3):257-261. 10.1166/sl.2006.031
Bur AJ, Wang FW, Thomas CL, Rose JL: In-line optical monitoring of polymer injection molding. Polymer Engineering and Science 2004,34(8):671-679. 10.1002/pen.760340809
Bosch P, Catalina F, Corrales T, Peinado C: Fluorescent probes for sensing processes in polymers. Chemistry-A European Journal 2005,11(15):4314. 10.1002/chem.200401349
Roos Y, Karel M: Crystallization of amorphous lactose. Journal of food science 2006,57(3):775-777. 10.1111/j.1365-2621.1992.tb08095.x
Yildiz ME, Kokini JL: Determination of Williams-Landel-Ferry constants for a food polymer system: Effect of water activity and moisture content. Journal of Rheology 2001, 45: 903-912. 10.1122/1.1380425
Dutta P, Bhattacharyya K: Ultrafast chemistry in complex and confined systems. Journal of Chemical Sciences 2004, 116: 5-16. 10.1007/BF02708207
Hara K, Bulgarevich DS, Kajimoto O: Pressure tuning of solvent viscosity for the formation of twisted intramolecular charge transfer state in 4, 4 diaminodiphenyl sulfone in alcohol solution. The Journal of chemical physics 1996,104(23):9431. 10.1063/1.471687
Suhling K, French PMW, Phillips D: Time-resolved fluorescence microscopy. Photochemical & Photobiological Sciences 2005, 4: 13-22.
Haidekker MA, Brady TP, Lichlyter D, Theodorakis EA: A ratiometric fluorescent viscosity sensor. Journal of the American Chemical Society 2006,128(2):398-399. 10.1021/ja056370a
Author information
Authors and Affiliations
Corresponding author
Additional information
Competing interests
The authors declare that they have no competing interests.
Authors' contributions
MH is responsible for the overall content and contributed the engineering aspects. ET contributed the chemistry-related content of this review. All authors have read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
This article is published under license to BioMed Central Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Haidekker, M.A., Theodorakis, E.A. Environment-sensitive behavior of fluorescent molecular rotors. J Biol Eng 4, 11 (2010). https://doi.org/10.1186/1754-1611-4-11
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/1754-1611-4-11