Abstract
Due to an increase in the commercial use of biodiesel and biodiesel blends, both ASTM D 6751 and EN 14214 include the acid number (AN) as an important quality parameter. It was found that determination of AN of biodiesel and biodiesel blends using the ASTM D 974 results in large values of repeatability (up to 73.41%) and larger percentage error (up to 42.88%). Therefore, ASTM D 974 has been modified using a lower concentration of base (0.02 M KOH instead of 0.1 M KOH) as well as reducing the amount of toxic titration solvent from 100 mL to only 10 mL. This makes the modified ASTM D 974 as a green analytical method which uses a reduced amount of toxic solvent. This modified method significantly reduced the maximum percentage error from 42.88 to 5.92%. The application of this modified ASTM D 974 for the determination of AN of biodiesel and biodiesel blends was studied. The accuracy of this modified ASTM D 974 for biodiesel (B100) was measured to be within 3.51% over the AN range of 0.313–0.525 mg KOH/g and maximum repeatability was decreased from 8.37 to 2.75% within this AN range which is far below the ASTM D 974 stated repeatability specifications. For B20, B10, B5, B2, and B1, the most accurate values were measured at AN values of 0.177, 0.067, 0.072, 0.126, and 0.096 mg KOH/g, respectively. Excellent linearity values of R 2 for calculated and experimentally determined AN were obtained. The difference between the experimental and the calculated AN for all biodiesel and biodiesel blend samples was within ± 0.018 mg KOH/g. This extensive study has demonstrated that this modified ASTM D 974 is a reliable method for the determination of AN and could be used for establishing the specifications of AN for biodiesel and biodiesel blends ranging from B1 to B20 in quality standards.
Similar content being viewed by others
References
Baig A, Ng FTT (2010) A Single-step solid acid-catalyzed process for the production of biodiesel from high free fatty acid feedstocks. Energy Fuels 24(9):4712–4720. doi:10.1021/ef901258b
Knothe G (2006) Analyzing biodiesel: standards and other methods. J Am Oil Chem Soc 83:823–833
ASTM (2009) Standard specification for biodiesel fuel blend stock (B100) for middle distillate fuels. Designated D 6751-09a
Fatty acid methyl esters: requirements and test methods, DIN EN 14214 (2003)
ASTM (2008) Standard test method for acid and base number by color-indicator titration, ASTM D 974-08
ASTM (2009) Standard test method for acid number of petroleum products by potentiometric titration. Designated D 664-09a
Mahajan S, Konar SK, Boocock DGB (2006) Determining the acid number of biodiesel. J Am Oil Chem Soc 83:567–570
Wang H, Tang H, Wilson J, Salley SO, Ng KYS (2008) Total acid number determination of biodiesel and biodiesel blends. J Am Oil Chem Soc 85:1083–1086
Clean cities fact sheet: biodiesel blends April 2008, National Renewable Energy Laboratory (NREL), USA. http://www.afdc.energy.gov/afdc/pdfs/42562.pdf (accessed in April 2010)
Tang H, Abunasser N, Wanga A, Clark BR, Wadumesthrige K, Zeng S, Kim M, Salley SO, Hirschlieb G, Wilson J, Ng KYS (2008) Quality survey of biodiesel blends sold at retail stations. Fuel 87:2951–2955
Acknowledgments
The authors acknowledge the Natural Science and Engineering Research Council (NSERC) of Canada, Strategic Projects Program, for financial support of this research. We also thank Rothsay for providing a sample of refurbished waste oils and fats based biodiesel.
Author information
Authors and Affiliations
Corresponding author
About this article
Cite this article
Baig, A., Ng, F.T.T. Determination of Acid Number of Biodiesel and Biodiesel Blends. J Am Oil Chem Soc 88, 243–253 (2011). https://doi.org/10.1007/s11746-010-1667-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11746-010-1667-x