Abstract
Nanotechnology applied to polymer foams is an emerging field. The possibility to add nanofillers to polymers and to expand them by supercritical carbon dioxide represents an important development in polymer foam production, tailoring the foams’ properties. In this study, polystyrene (PS) composites with cellulose nanofibers (CNF) were obtained by producing PS/CNF nanocomposites and subsequently expanding them with supercritical CO2. The viscosity, mechanical and dynamic-mechanical properties of non-expanded composites were obtained. The morphology and compressive strength of the expanded composites were evaluated. The non-expanded composites’ mechanical properties remained unchanged, and the viscosity increased with the addition of CNF. PS/CNF non-expanded composites displayed higher storage modulus in the rubbery region with increasing CNF content. The expanded foams displayed smaller cell size as CNF is introduced, which increased the compressive strength and decreased the deformation at 5 wt% CNF. This allows the tailoring of the mechanical properties and cell size with varying CNF content to better suit a wide range of applications.
Similar content being viewed by others
References
Yang J, Wu M, Chen F, Fei Z, Zhong M (2011) Preparation, characterization, and supercritical carbon dioxide foaming of polystyrene/graphene oxide composites. J Supercrit Fluid 56:201–207. https://doi.org/10.1016/j.supflu.2010.12.014
Mori T, Hayashi H, Okamoto M, Yamasaki S, Hayami H (2009) Foam processing of polyethylene ionomers with supercritical CO2. Compos Part A Appl Sci 40:1708–1716. https://doi.org/10.1016/j.compositesa.2009.08.018
Goren K, Chen L, Schadler LS, Ozisik R (2010) Influence of nanoparticle surface chemistry and size on supercritical carbon dioxide processed nanocomposite foam morphology. J Supercrit Fluid 51:420–427. https://doi.org/10.1016/j.supflu.2009.09.007
Lee LJ, Zeng C, Cao X, Han X, Shen J, Xu G (2005) Polymer nanocomposite foams. Compos Sci Technol 65:2344–2363. https://doi.org/10.1016/j.compscitech.2005.06.016
Kourki H, Famili MHN, Mortezaei M, Malekipirbazar M (2017) Mixing challenges for SiO2/polystyrene nanocomposites. J Thermoplast Compos 1:1–18. https://doi.org/10.1177/0892705717718599
Famili MHN, Janani H, Enayati MS (2010) Foaming of a polymer-nanoparticle system: effect of the particle properties. J Appl Polym Sci 119:2847–2856. https://doi.org/10.1002/app.32969
Wong A, Mark LH, Hasan MM, Park CB (2014) The synergy of supercritical CO2 and supercritical N2 in foaming of polystyrene for cell nucleation. J Supercrit Fluid 90:35–43. https://doi.org/10.1016/j.supflu.2014.03.001
Tsivintzelis I, Sanxaridou G, Pavlidou E, Panayiotou C (2016) Foaming of polymers with supercritical fluids: a thermodynamic investigation. J Supercrit Fluid 110:240–250. https://doi.org/10.1016/j.supflu.2015.11.025
Jacobs MA, Kemmere MF, Keurentjes JTF (2004) Foam processing of poly(ethylene-co-vinyl acetate) rubber using supercritical carbon dioxide. Polymer 45:7539–7547. https://doi.org/10.1016/j.polymer.2004.08.061
Tsivintzelis I, Angelopoulou AG, Panayiotou C (2007) Foaming of polymers with supercritical CO2: an experimental and theoretical study. Polymer 48:5928–5939. https://doi.org/10.1016/j.polymer.2007.08.004
Ngo TTV, Rumeau JD, Whittaker AK, Gerard JF (2010) Processing of nanocomposite foams in supercritical carbon dioxide. Part I: effect of surfactant. Polymer 51:3436–3444. https://doi.org/10.1016/j.polymer.2010.05.039
Cho SY, Park HH, Yun YS, Jin HJ (2013) Influence of cellulose nanofibers on the morphology and physical properties of poly(lactic acid) foaming by supercritical carbon dioxide. Macromol Res 21:529–533. https://doi.org/10.1007/s13233-013-1057-y
Siqueira G, Bras J, Dufresne A (2009) Cellulose whiskers versus microfibrils: influence of the nature of the nanoparticle and its surface functionalization on the thermal and mechanical properties of nanocomposites. Biomacromol 10:425–432. https://doi.org/10.1021/bm801193d
Peng Y, Gardner DJ, Han Y (2012) Drying cellulose nanofibrils: in search of a suitable method. Cellulose 19:91–102. https://doi.org/10.1007/s10570-011-9630-z
Zimmermann MVG, Borsoi C, Lavoratti A, Zanini M, Zattera AJ, Santana RMC (2016) Drying techniques applied to cellulose nanofibers. J Reinf Plast Comp 35:628–643. https://doi.org/10.1177/0731684415626286
Reverchon E, Cardea S (2007) Production of controlled polymeric foams by supercritical CO2. J Supercrit Fluid 40:144–152. https://doi.org/10.1016/j.supflu.2006.04.013
Sauceau M, Nikitine C, Rodier C, Fages J (2007) Effect of supercritical carbon dioxide on polystyrene extrusion. J Supercrit Fluid 43:367–373. https://doi.org/10.1016/j.supflu.2007.05.014
Arora KA, Lesser AJ, McCarthy TJ (1998) Preparation and characterization of microcellular polystyrene foams processed in supercritical carbon dioxide. Macromolecules 31:4614–4620. https://doi.org/10.1021/ma971811z
Poletto M, Zattera AJ (2015) Mechanical and dynamic mechanical properties of polystyrene composites reinforced with cellulose fibers. J Thermoplas Compos 30:1242–1254. https://doi.org/10.1177/0892705715619967
Spence KL, Venditti RA, Rojas OJ, Habibi Y, Pawlak JJ (2011) A comparative study of energy consumption and physical properties of microfibrillated cellulose produced by different processing methods. Cellulose 18:1097–1111. https://doi.org/10.1007/s10570-011-9533-z
Kalia S, Boufi S, Celli A, Kango S (2014) Nanofibrillated cellulose: surface modification and potential applications. Colloid Polym Sci 292:5–31. https://doi.org/10.1007/s00396-013-3112-9
Petchwattana N, Covavisaruch S (2011) Influences of particle sizes and contents of chemical blowing agents on foaming wood plastic composites prepared from poly(vinyl chloride) and rice hull. Mater Des 32:2844–2850. https://doi.org/10.1016/j.matdes.2010.12.044
Jonoobi M, Mathew AP, Oksman K (2012) Producing low-cost cellulose nanofiber from sludge as new source of raw materials. Ind Crop Prod 40:232–238. https://doi.org/10.1016/j.indcrop.2012.03.018
Lavoratti A, Scienza LC, Zattera AJ (2016) Dynamic-mechanical and thermomechanical properties of cellulose nanofiber/polyester resin composites. Carbohyd Polym 136:955–963. https://doi.org/10.1016/j.carbpol.2015.10.008
Jabbar A, Militký J, Wiener J, Kale BM, Ali U, Rwawiire S (2017) Nanocellulose coated woven jute/green epoxy composites: characterization of mechanical and dynamic mechanical behavior. Compos Struct 161:340–349. https://doi.org/10.1016/j.compstruct.2016.11.062
Ornaghi HL, Bolner AS, Fiorio R, Zattera AJ, Amico SC (2010) Mechanical and dynamic mechanical analysis of hybrid composites molded by resin transfer molding. J Appl Polym Sci 118:887–896. https://doi.org/10.1002/app.32388
Romanzini D, Lavoratti A, Ornaghi HL, Amico SC, Zattera AJ (2013) Influence of fiber content on the Mechanical and dynamic mechanical properties of glass/ramie polymer composites. Mater Des 47:9–15. https://doi.org/10.1016/j.matdes.2012.12.029
Chirayil CJ, Mathew L, Hassan PA, Mozetic M, Thomas S (2014) Rheological behaviour of nanocellulose reinforced unsaturated polyester nanocomposites. Int J Biol Macromol 69:274–281. https://doi.org/10.1016/j.ijbiomac.2014.05.055
Khiari R (2017) Valorization of agricultural residues for cellulose nanofibrils production and their use in nanocomposite manufacturing. Int J Polym Sci 2017:1–10. https://doi.org/10.1155/2017/6361245
Margem FM, Monteiro SN, Neto JB, Rodriguez RJS, Soares BG (2010) The dynamic-mechanical behavior of epoxy matrix composites reinforced with ramie fibers. Matéria 15:164–171. https://doi.org/10.1590/S1517-70762010000200012
Lee KY, Aitomäki Y, Berglund LA, Oksman K, Bismarck A (2014) On the use of nanocellulose as reinforcement in polymer matrix composites. Compos Sci Technol 105:15–27. https://doi.org/10.1016/j.compscitech.2014.08.032
Nikfarjam N, Qazvini NT, Deng Y (2015) Surfactant free Pickering emulsion polymerization of styrene in w/o/w system using cellulose nanofibrils. Eur Polym J 64:179–188. https://doi.org/10.1016/j.eurpolymj.2015.01.007
Doroudiani S, Kortschot MT (2004) Expanded wood fiber polystyrene composites: processing–structure–mechanical properties relationships. J Thermoplast Compos 17:13–30. https://doi.org/10.1177/0892705704035405
Eaves D (2004) Handbook of polymer foams. Smithers Rapra, Shrewsbury
Zhao J, Zhao Q, Wang L, Wang C, Guo B, Park CB, Wang G (2018) Development of high thermal insulation and compressive strength BPP foams using mold-opening foam injection molding with in situ fibrillated PTFE fibers. Eur Polym J 98:1–10. https://doi.org/10.1016/j.eurpolymj.2017.11.001
Zhao J, Zhao Q, Wang C, Guo B, Park CB, Wang G (2017) High thermal insulation and compressive strength polypropylene foams fabricated by high-pressure foam injection molding and mold opening of nano-fibrillar composites. Mater Design 131:1–11. https://doi.org/10.1016/j.matdes.2017.05.093
Acknowledgements
The authors would like to express their gratitude to the National Council of Technological and Scientific Development (CNPq), and the Secretariat of Science, Innovation and Development of Rio Grande do Sul (SCT/RS) for the financial support.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zimmermann, M.V.G., Boakoski, D.G., Lavoratti, A. et al. Influence of cellulose nanofiber content on the expansion of polystyrene nanocomposites expanded by supercritical CO2. Polym. Bull. 75, 5809–5824 (2018). https://doi.org/10.1007/s00289-018-2360-8
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00289-018-2360-8