Abstract
The time-temperature-transformation behavior of a metastable β-titanium alloy, Ti-3A1-8V-6Cr-4Zr-4Mo (RMI 38644), has been examined using hardness, X-ray measurements, and optical and transmission electron microscopy. This examination has shown that a variety of metastable and stable phases may form in this alloy system. These include metastable zones, ω, both Burgers (Type 1) α and non-Burgers (Type 2) α, TiCr2, and a Ti-Zr-silicide. A composite TTT diagram is presented which describes the influence of aging time and temperature on the stability of these phases. Finally, the appearance of these transformation products is correlated with the observed hardness changes when RMI 38644 is aged at elevated temperatures.
Similar content being viewed by others
References
V. C. Peterson and J. B. Guernsey:Manufacturing Procedures for a New High Strength Beta Titanium Alloy Having Superior Formability, AFML-TR-69-171, June 1969.
N. V. Ageev and L. A. Petrova:Metastable Beta-Alloys of Titanium, FTD-HT- 23-0154-73, April 1973.
E. Bohanek: “Deep Hardenable Titanium Alloys for Large Airframe Elements,”Titanium Sci. Technol., R. I. Jaffee and H. N. Burte, eds., p. 1993, Plenum Press, New York, 1973.
R. G. Berryman, F. H. Froes, J. C. Chesnutt, C. G. Rhodes, J. C. Williams, and R. F. Malone:High Toughness Titanium Alloy Development, NAVAIR TFD-74-657, July 1974.
F. H. Froes, R. F. Malone, V. C. Petersen, C. G. Rhodes, J. C. Chesnutt, and J. C. Williams:Research on Deep Hardenable Titanium Alloy for Large Air- frame Structural Members, AFML-TR-7541, September 1975.
R. Chait and C. Stead:Met. Trans. B, 1977, vol. 8B, pp. 371–76.
M. J. Blackburn, W. H. Smyrl, and J. A. Feeney: “Titanium Alloys,”Stress Corrosion Cracking in High Strength Steels and in Titanium and Aluminum Alloys, B. F. Brown, ed., p. 245, Naval Research Lab., Washington, D.C., 1972.
R. Chait and T. S. DeSisto: “The Fracture Toughness of Three Titanium Alloys,”Titanium Sci. Technol., R. I. Jaffee and H. M. Burte, eds., p. 1377, Plenum Press, New York, 1973.
D. N. Williams, R. A. Wood, and E. S. Bartlett:Met. Trans., 1972, vol. 3, pp. 1529–36.
G. Lenning: “Formable Sheet Titanium Alloys,” AFML-TR-76-45, August 1976.
T. B. Gurganus:Improvement of Reliability and the Mechanical Properties of Titanium Alloy Forgings, AFML-TR-75-211, December 1975.
C. G. Rhodes and N. E. Paton:Met. Trans. A, 1977, vol. 8A, pp. 1749–61.
J. W. Hagemeyer and D. E. Gordon: “Properties of Two Beta Titanium Alloys After Aging at Several Different Temperatures,” Titanium Sci. Technol, R. I. Jaffee and H. M. Burte, eds., p. 1957, Plenum Press, New York, 1973.
D. E. Gordon and J. W. Hagemeyer:J. Mater. Sci., 1975, vol. 10, pp. 1725–31.
W. F. Czyrlik and M. Levy:Corrosion, 1976, vol. 32, pp. 99–102.
H. J. Rack:Met. Trans. A, 1976, vol. 7A, pp. 1571–76.
G. A. Sargent, H. Huang, and R. J. DeAngelis:J. Mater. Sci., 1974, vol. 9, pp. 487–90.
T. J. Headley: “Autocatalytic Nucleation of Omega Phase in a Beta-Titanium Alloy,”34th Annual Proc. of the Electron Microscope Society of America, G. W. Bailey, ed., p. 604, Claitor’s, New Orleans, 1976.
R. J. DeAngelis, Y. H. Huang, and G. A. Sargent:Scr. Met., 1974, vol. 8, pp. 339–42.
H. J. Rack and T. J. Headley: Sandia Laboratories, Albuquerque, NM, Un- published research, 1976.
T. J. Headley and H. J. Rack:Scr. Met., 1975, vol. 9, pp. 399–406.
H. J. Rack, D. Kalish, and K. D. Fike:Mater. Sci. Eng., 1970, vol. 6, pp. 181–98.
R. A. Spurting, C. G. Rhodes, and J. C. Williams:Met. Trans., 1974, vol. 6, pp. 2597–2600.
G. M. Pennock, H. N. Flower, and D. R. F. West:Metallography, 1977, vol. 10, pp. 43–53.
M. H. Mueller and L. Heaton:Determination of Lattice Parameter with the Aid of a Computer, Argonne National Laboratory, Argonne, 111., SNL-6176, January 1961.
F. H. Froes, J. M. Capenos, and M. G. H. Wells: “Alloy Partitioning in Beta-Ill and Effect on Aging Characteristics,”Titanium Sci. Technol., R. I. Jaffee and H. M. Burte, eds., p. 1621, Plenum Press, New York, 1973.
H. M. Flower, P. R. Swann, and D. R. F. West: Met. Trans., 1971. vol. 2, pp. 3289–97.
S. Seagle: RMI, Inc., Niles, Ohio, Private communication, January 1975.
G. Hari Narayanan and T. F. Archbold:Met. Trans., 1970, vol. 1, pp. 2281–90.
G. Hari Narayanan, T. S. Luhman, T. F. Archbold, R. Taggart, and D. H. Polonis:Metallography, 1971, vol. 4, pp. 343–58.
J. C. William, B. S. Hickman, and D. H. Leslie:Met. Trans., 1971, vol. 2, pp. 477–84.
M. J. Blackburn and J. C. Williams:Trans. TMS-AIME, 1968, vol. 242, pp. 2461–69.
J. A. Feeney and M. J. Blackburn:Met. Trans., 1970, vol. 1, pp. 3309–23.
J. C. Williams and M. J. Blackburn:Trans. TMS-AIME, 1969, vol. 245, pp. 2352–55.
C. G. Rhodes and J. C. Williams:Met. Trans. A, 1975, vol. 6A, pp. 2103–14.
G. Hari Narayanan and T. F. Archbold: “Microstructure-Mechanical Property- Fracture Relationships in All-Beta Titanium Alloy-Ti-13V-l 1O-3A1,”Elec- tron Microscopy and Structure of Materials, G. Thomas, R. M. Fulrath, and R. M. Fisher, eds., p. 657, Univ. of Calif. Press, Berkeley, CA, 1972.
H. J. Rack:Met. Trans. A, 1975, vol. 6A, pp. 947–49.
Data from Powder Diffraction File Card No. 5-713, Joint Committee on Powder Diffraction Standards, International Centre for Diffraction Data, Swarthmore, PA, 1977.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Headley, T.J., Rack, H.J. Phase transformations in Ti- 3AI- 8V- 6Cr- 4Zr- 4Mo. Metall Trans A 10, 909–920 (1979). https://doi.org/10.1007/BF02658310
Issue Date:
DOI: https://doi.org/10.1007/BF02658310