Abstract
The roles of grain-boundary sliding (GBS) and of other creep mechanisms in creep and fine-grain superplasticity are presented in relation to a model based on the division of grains into their central “cores“ and peripheral “mantles”; GBS and its accommodation is limited to the latter, which changes with the mode of accommodation,viz by fold formation, dislocation motion in the mantle or pure diffusion. This description is used to adapt from the literature or develop equations for creep rate based on dislocation or vacancy mechanisms, which are then combined to give plots of the various regimes of superplastic (or creep) behavior, all of which involve GBS in a quantitatively defined manner. The predictions of these equations are compared with a number of results in the literature and with those of a lead-thallium alloy of grain sizes intermediate between superplastic behavior and normal creep. Some preliminary comparisons of measured GBS are also made with the predictions of the model. Agreement is good.
Similar content being viewed by others
References
R. C. Gifkins:J. Inst. Metals, 1967, vol. 95, pp. 373–77.
R. C. Gifkins:Scr. Met., 1973, vol. 7, pp. 27–34.
R. C. Gifkins:J. Inst. Metals, 1952-53, vol. 81, pp. 417–25.
R. C. Gifkins:Acta Met., 1958, vol. 6, pp. 132–33.
R. B. Nicholson:Electron Microscopy and Structure of Materials, G. Thomas et al, eds., pp. 689–71, University of California Press, Los Angeles, Calif., 1972.
W. Boas and M. E. Hargreaves:Proc. Roy. Soc., 1948, vol. 193A, pp. 89–97.
M. F. Ashby:Phil. Mag., 1970, vol. 21, pp. 399–424.
R. C. Gifkins:CSIRO Physical Metallurgy Section Report No. 2, pp. 1-35, CSIRO Melbourne, Australia, May 1972.
R. L. Bell and T. G. Langdon:Interfaces Conference Melbourne, R. C. Gifkins, ed., pp. 115–37, Butterworths, Melbourne, 1970.
D. L. Holt and W. A. Backofen:Trans. ASM, 1966, vol. 59, pp. 55–68.
R. Raj and M. F. Ashby:Met. Trans., 1971, vol. 2, pp. 1113–27.
R. C. Gifkins:J. Aust. Inst. Metals, 1973, vol. 17, pp. 137–45.
J. Weertman:Trans. ASM, 1968, vol. 61, pp. 681–94.
A. Ball and M. M. Hutchison:Metal Sci. J., 1969, vol. 3, pp. 3–7.
A. K. Mukherjee:Mater. Sci. Eng., 1971, vol. 8, pp. 83–89.
M. F. Ashby and R. A. Verrall:Acta Met., 1973, vol. 21, pp. 149–63.
J. R. Cahoon:Metal Sci. J., 1975, vol. 9, pp. 346–52.
F. A. Mohamed and T G. Langdon:Acta Met., 1975, vol. 23, pp. 117–23.
F. A. Mohamed, S-A. Shei, and T. G. Langdon:Acta Met., 1975, vol. 23, p. 1143.
F. A. Nichols:Mater. Sci. Eng., 1971, vol. 8, pp. 108–20.
R. C. Gifkins:Scr. Met., 1976, vol. 10, pp. 000.
R. C. Gifkins:Mater. Sci. Eng., 1967, vol. 2, pp. 181–92.
H. F. Ryan and J. W. Suiter:Phil. Mag., 1964, vol. 10, pp. 727–79.
P. L. Bolin, J. T. Scardina, R. J. Bayuzick and B. N. Ranganathan:Can. Met. Quart., 1974, vol. 13, pp. 91–98.
M. Pahutora, J. Cadek, and P. Rys:Scr. Met., 1971, vol. 5, pp. 137–41.
M. Biscondi:J. Phys., in press.
P. A. Turner:Ph. D. Thesis, Imperial College, London, 1963.
C. J. Smithells:Metals Reference Book, 4th ed., vol. 1, no. 3, Butterworth, London, 1947.
H. Gleiter and B. Chalmers:Progress in Materials Science, B. Chalmers, J. W. Christian, and T. B. Massalski, eds., vol. 16, Pergamon, Oxford, 1972.
O. M. Sutton:Phys. Rev., 1953, vol. 91, pp. 816–20.
P. Shewmon:Diffusion in Solids, McGraw-Hill, New York, 1963.
A. K. Sturges:M. A. Sc. Thesis, University of British Columbia, 1970.
D. M. Avery and W. A. Backofen:Trans. ASM, 1965, vol. 58, pp. 551–62.
J. White and R. C. Gifkins:Unpublished results, Metallurgy Department, University of Melbourne, Parkville, Victoria, Australia.
A. E. Geckinli and C. R. Barrett:Scr. Met., 1974, vol. 8, pp. 115–20.
J. Friedel:Dislocations, Pergamon, Oxford, 1964.
B. Okkerse:Acta Met., 1954, vol. 2, pp. 551–53.
R. C. Gifkins:ibid. 1958, vol. 6, pp. 132–33.
F. BoUing:Trans. TMS-AIME, 1962, vol. 224, pp. 635–36.
H. W. Hayden, R. C. Gibson, H. F. Merrick, and J. H. Brophy:Trans. ASM, 1967, vol. 60, pp. 3–14.
D. L. Holt and W. A. Backofen:ibid, pp. 755–68.
S. Sagat, P. Blenkinsop, and D. M. R. Taplin:J. Inst. Metals, 1972, vol. 100, pp. 268–72.
R. C. Cook and N. R. Risebrough:Scr. Met., 1968, vol. 2, pp. 487–89.
M. F. Ashby:Acta Met., 1972, vol. 20, pp. 887–97.
T. G. Langdon and F. A. Mohamed:“Grain Boundaries in Engineering Materials,“4th Bolton Landing Conference, June, 1974, Claitor, Baton Rouge, La., U. S. A., 1975.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gifkins, R.C. Grain-boundary sliding and its accommodation during creep and superplasticity. Metall Trans A 7, 1225–1232 (1976). https://doi.org/10.1007/BF02656607
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02656607