Abstract
Piercing mandrels for the skew rolling mill at OAO Severskii Trubnyi Zavod are compared. The influence of the shape and length of the mandrel’s working section and its position in the deformation zone on the piercing of the blank is investigated in terms of the cyclic-shaping parameters.
Similar content being viewed by others
References
Hayashi, C. and Yamakawa, T., New methods piercing mills setting, ISIJ Intern., 1998, vol. 37, no. 11, p. 1225.
Kummerling, R., Transverse skew rolling of pipe, Izv. Vyssh. Uchebn. Zaved., Chern. Metall., 1989, no. 10, pp. 9–16.
Golubchik, R.M., Polukhin, P.I., Matveev, Yu.M., et al., Issledovanie protsessov proizvodstva trub (Polyarizatsionno-opticheskii metod) (Polarization-Optical Study of Pipe Piercing), Moscow: Metallurgiya, 1960.
Golubchik, R.M., Merkulov, D.V., Novikov, M.V., et al., Improving the shape of the mandrel’s working section when piercing blanks, Izv. Vyssh. Uchebn. Zaved., Chern. Metall., 2002, no. 11, pp. 30–33.
Panov, E.I., Stress-strain state of a blank in transverse skew rolling, Metallurg, 2003, no. 12, pp. 34–38.
Golubchik, R.M. and Lebedev, A.V., New methods piercing mill setting relating to the cyclic forming of hollows, History and Future of Seamless Tubes: 7th International Conference, Karlovy Vary, 1999, pp. (1/8)–(1/17).
Golubchik, R.M., Merkulov, D.V., and Chepurin, M.V., Improving the algorithm for calculating the cyclic-shaping parameters in skew rolling, Proizv. Prokata, 1999, no. 6, pp. 19–24.
Merkulov, D.V., Golubchik, R.M., and Chepurin, M.V., Piercing blanks in skew rolling mills of different design, Tr. IV mezhdunarodnogo kongressa prokatchikov (Proceedings of 4th International Congress of Rolling Specialists), Moscow: AO Chermetinformatsiya, 2002, vol. 2, pp. 82–87.
Merkulov, D.V. and Toporov, V.A., Minimum possible mandrel length in piercing blanks, Prokatn. Proizv., 2013, no. 1, pp. 22–25.
Golubchik, R.M., Investigation of skew rolling, Extended Abstract of Cand. Sci. Dissertation, Moscow Institute of Steel and Alloys, Moscow, 1961.
Tolmachev, V.S., Degai, A.S., Zuev, M.V., and Tereshin, A.V., USSR Inventor’s Certificate 2372159, Byull. Izobret., 2009, no. 31.
Merkulov, D.V., Titova, S.V., Novikov, M.V., et al., Using the parameters of cyclic shaping to determine the working-section profile of piercing mandrels, Tekhnol. Met., 2002, no. 2, pp. 5–8.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © V.A. Toporov, M.V. Chepurin, V.A. Parfenov, A.I. Stepanov, 2014, published in “Stal’,” 2014, No. 6, pp. 63–66.
About this article
Cite this article
Toporov, V.A., Chepurin, M.V., Parfenov, V.A. et al. Skew rolling in the piercing of blanks. Steel Transl. 44, 452–455 (2014). https://doi.org/10.3103/S0967091214060163
Published:
Issue Date:
DOI: https://doi.org/10.3103/S0967091214060163