CAD/CAM splint based on soft tissue 3D simulation for treatment of facial asymmetry
- 778 Downloads
Most cases of facial asymmetry involve yaw deformity, and determination of the yaw correction level is very difficult.
We use three-dimensional soft tissue simulation to determine the yaw correction level. This three-dimensional simulation is based on the addition of cephalometric prediction to gradual yaw correction. Optimal yaw correction is determined visually, and an intermediate splint is fabricated with computer-aided design and computer-aided manufacturing. Application of positioning devices and the performance of horseshoe osteotomy are advisable.
With this procedure, accurate repositioning of jaws was confirmed and patients obtained fairly good facial contour.
This procedure is a promising method for a widespread, predictable treatment of facial asymmetry.
KeywordsFacial asymmetry 3D simulation Soft tissue CAD/CAM Orthognathic surgery Horseshoe osteotomy Positioning device
Management of facial asymmetry is very challenging. Treatment followed by two-dimensional (2D) analysis alone, such as cephalometric prediction, can achieve midline correction. However, it is insufficient for facial contour correction. Three-dimensional (3D) models and/or 3D simulation are often used to overcome this issue. However, these bone-level simulations also have some limitations. Most cases of asymmetry require correction of yaw, and changes in yaw have a significant influence on the facial contour. Evaluation of facial contour is not sufficient only from the frontal and lateral directions; it should also be performed from the oblique direction. Our strategy for facial asymmetry is as follows. Using soft tissue simulation, gradual changes in yaw are evaluated from various angles to determine the optimal correction of yaw. Based on the determined movement, an intermediate splint is made with computer-aided design and computer-aided manufacturing (CAD/CAM). We developed 3D positioning devices [1, 2] to maintain the original position of the mandible during surgery. Because treatment of asymmetry often requires upward and/or backward repositioning of the maxillary segment bilaterally or unilaterally, we developed a modified horseshoe osteotomy technique to avoid bony interference of the posterior part of the maxilla [3, 4]. This sequential process is explained through a case presentation.
Computed tomography (CT) is performed with a presurgical splint that slightly opens the mandible from centric occlusion. The DICOM data of CT are converted into simulation software (SimPlant Pro OMS Ver. 13.0; Materialize, Leuven, Belgium) (Fig. 1c, d).
The metrical analysis results of cephalometric prediction are input into the simulation software, and 3D virtual prediction is performed (Fig. 2a). Midline correction can be achieved in many cases only by correction of the pitch and roll based on frontal and lateral cephalograms. Without yaw correction, however, a satisfactory facial contour cannot be achieved.
Gradual yaw correction while maintaining the anterior midline as a hinge is performed on soft tissue virtual simulation. Optimal yaw correction is determined visually not only from the frontal view but also from the oblique view (Fig. 2b, c). The facial contour gradually improves with correction of the yaw; at a certain critical point, however, the contour becomes worse. This critical point is the optimal point of yaw correction. However, multiple inspectors are required because this is an inspectional determination. The critical point is usually determined by one or more oral surgeons and orthodontists. The movement is determined from soft tissue-based simulation and is usually too complex to realize with facebow transfer and plaster model trimming because laboratory error is much larger.
An intermediate splint is produced by CAD/CAM. First, plaster models of the dental arches are laser-scanned (Fig. 3a). Using the virtual repositioning situation of the maxilla (the mandible is in an in situ position) (Fig. 3b), the digital data of the dental arches are fused to the bone data (Fig. 3c). Based on this intermaxillary relationship, an intermediate splint is produced by CAD/CAM (Fig. 4).
For proper repositioning of the maxilla using the intermediate splint, the mandible should be in exactly the same position as that on presurgical CT with the presurgical splint. A simple 3D positioning device that we developed [1, 2] is then used (Fig. 5).
Because maxillary deficiency is rarely involved in cases of facial asymmetry, most affected patients require backward and upward repositioning of the maxilla unilaterally or bilaterally. In these cases, complete removal of bony interference of the posterior part of the maxilla is mandatory. Application of the modified horseshoe osteotomy technique that we developed is effective for this purpose [3, 4, 5].
In simple cases of jaw deformity without yaw correction, conventional cephalometric prediction works well. However, patients with yaw deformity require analyses with 3D models or 3D virtual simulation. In most cases of facial asymmetry, even if 3D analyses are performed, hard tissue simulation alone does not provide a satisfactory outcome. We therefore propose yaw correction based on soft tissue simulation to overcome this problem. Our major correction strategy is based on cephalometric analysis with an enormous amount of accumulated knowledge, and soft tissue virtual simulation covers the weak points. Although the accuracy of virtual soft tissue prediction does not reach the level of the actual use of postoperative prediction , soft tissue evaluation of virtual yaw correction might provide a better vector to obtain better facial contour. Further research is needed before virtual soft tissue simulation is used for soft tissue prediction.
Optimal reproduction of this simulation technique in the operative field is necessary to successfully use this procedure. European researchers invented interactive visualizing displays to reposition the maxilla into the simulated position . However, they were unrealistic for routine orthognathic surgery and were extremely time-consuming and costly. Owing to recent improvement and popularization of 3D printers, various types of surgical stents with CAD/CAM for positioning of bone segments as well as osteotomy guides have been reported [6, 8, 9]. Although they require less time and cost, a certain amount of manpower and money are also necessary to design and manufacture these complex structures.
The CAD/CAM splint we used is custom-made by a manufacturer. The manufacturer also performs laser-scanning of plaster dental models. The operators must only perform virtual simulation and fusion between the jaw simulation and dental arch data. Our technique combines the CAD/CAM splint and a simple intraoperative positioning device, thus using the least cost and time to achieve the desired outcome. Additionally, it is possible to achieve upward and backward repositioning of the maxilla without bony interference; this is often needed in cases of facial asymmetry. The accuracy and reliability of the combination of the positioning device and horseshoe osteotomy have been reported elsewhere .
Our strategy can be used anywhere that simulation software is available and is a promising method for a widespread, predictable treatment of facial asymmetry.
Written informed consent was obtained from the patient for the publication of this report and any accompanying images.
- 5.Tominaga K, Habu M, Iwanaga K, Kodama M, Tsurushima H, Kokuryo S, Miyamoto I, Fukudome Y, Yoshioka I (2015) Maxillary single-jaw surgery combining Le Fort I and modified horseshoe osteotomies for the correction of maxillary excess. Int J Oral Maxillofac Surg http://dx.doi.org/10.1016/j.ijom.2015.10.020
- 6.Zinser MJ, Sailer HF, Ritter L, Baumann B, Maegele M, Zoller JE (2013) A paradigm shift in orthognathic surgery? A comparison of navigation, computer-aided designed/computer-aided manufactured splints, and “classic” intermaxillary splints to surgical transfer of virtual orthognathic planning. J Oral Maxillofac Surg 71:2151, e1-2151.e21CrossRefPubMedGoogle Scholar
- 10.Kokuryo S, Habu M, Miyamoto I, Uehara M, Kodama M, Iwanaga K, Yoshika I, Tominaga K (2014) Predicrability and accuracy of maxillary repositioning during bimaxillary surgery using a three-dimensional positioning technique. Oral Surg Oral Med Oral Pathol Oral Radiol 118:187–193CrossRefPubMedGoogle Scholar
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.