Abstract
Background
Anaerobic digestate is the effluent from anaerobic digestion of organic wastes. It contains a significant amount of nutrients and lignocellulosic materials, even though anaerobic digestion consumed a large portion of organic matters in the wastes. Utilizing the nutrients and lignocellulosic materials in the digestate is critical to significantly improve efficiency of anaerobic digestion technology and generate value-added chemical and fuel products from the organic wastes. Therefore, this study focused on developing an integrated process that uses biogas energy to power fungal fermentation and converts remaining carbon sources, nutrients, and water in the digestate into biofuel precursor-lipid.
Results
The process contains two unit operations of anaerobic digestion and digestate utilization. The digestate utilization includes alkali treatment of the mixture feed of solid and liquid digestates, enzymatic hydrolysis for mono-sugar release, overliming detoxification, and fungal fermentation for lipid accumulation. The experimental results conclude that 5 h and 30 °C were the preferred conditions for the overliming detoxification regarding lipid accumulation of the following fungal cultivation. The repeated-batch fungal fermentation enhanced lipid accumulation, which led to a final lipid concentration of 3.16 g/L on the digestate with 10% dry matter. The mass and energy balance analysis further indicates that the digestate had enough water for the process uses and the biogas energy was able to balance the needs of individual unit operations.
Conclusions
A fresh-water-free and energy-positive process of lipid production from anaerobic digestate was achieved by integrating anaerobic digestion and fungal fermentation. The integration addresses the issues that both biofuel industry and waste management encounter—high water and energy demand of biofuel precursor production and few digestate utilization approaches of organic waste treatment.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Background
Anaerobic digestion (AD) is a biological conversion process that has been proven effective at converting wet organic wastes into biogas, and capable of alleviating the environmental concerns associated with wastes while also producing clean electricity [1–3]. Recently, an increasing number of animal farms are using AD as part of their manure management strategy to produce methane as a renewable energy source [4]. In spite of advantages of renewable energy production and waste confinement, AD only partially utilizes the organic matter in waste streams, particularly for wastes rich in lignocellulosic materials such as dairy/cattle manure and crop residues. The AD effluent (the whole slurry after the digestion) still has relatively high levels of chemical oxygen demand (COD), fiber content, and nutrients (nitrogen and phosphorus). Further treatment is necessary to completely utilize all components in the organic wastes. The AD effluent is commonly separated by a liquid/solid separation unit into two streams: nitrogen- and phosphorus-rich liquid digestate, and fiber-rich solid digestate.
The solid digestate (AD fiber) has been widely recognized by scientific communities as a recalcitrant material that has limited applications such as soil amendment, animal bedding, and plant growing media [5]. Recent studies indicated that compared to other energy crops and agricultural residues, AD fiber demonstrates similar performance as a feedstock for bioethanol and biodiesel production [6–8], which significantly expands the potential application of AD fiber and enhances the economic benefits of anaerobic digestion technology. During the process of AD fiber utilization, chemical pretreatment is required to disrupt the internal association between fiber components and enable saccharification of cellulose and hemicellulose. However, such pretreatment also generates by-products (i.e., furfural, hydroxymethylfurfural, uronic acids, and phenolic compounds) that inhibit the following fermentation process [9, 10]. Our previous studies applied either washing or co-treatment with other feedstocks to reduce the inhibition [6, 8]. In this study, the AD fiber was used as the main feedstock for fermentation, and the washing step was not applied. Instead, a detoxification step is adopted to alleviate the inhibitory effects of the lignocellulose-derived by-products. Many detoxification approaches have been studied to date, such as overliming, reducing agents, polymers, and liquid–liquid extraction [11–14]. Among these approaches, overliming is considered to be as the most effective due to its advantages of less energy consumption, simple operation, and good performance [15, 16]. However, it has also been reported that overliming could cause sugar losses [16]. Therefore, overliming as the selected method for hydrolysate detoxification was investigated in this paper.
The liquid digestate, rich in nitrogen and phosphorus, is commonly used as irrigation water during the growing seasons [17]. However, seasonal demand of such nutrients requires a large storage capability to hold the liquid digestate. In addition, land application of liquid digestate is dependent on crop nutrient demand (nitrogen and phosphorus), which could result in great uncertainty and high cost of liquid digestate handling. To improve economic and environmental sustainability of the liquid digestate handling, alternative approaches are critically needed. Meanwhile, lignocellulosic biorefining demands a significant amount of water for biofuel production, which has triggered concerns about the sustainability of the second-generation biofuel production [18]. Considering the water and nutrient contents in the liquid digestate, if the liquid digestate can be used as the processing water for fermentative biofuel production, it would be an effective solution to address the water demand issue.
Considering the fact that some toxins could remain in the hydrolysate after the detoxification, the working microbes in the following fermentation must be robust enough to withstand them. Our previous studies have demonstrated that the oleaginous fungus, Mortierella isabellina, can tolerate relatively high concentrations of toxic compounds in lignocellulosic hydrolysates as well as efficiently consume glucose, xylose, and acetate for lipid accumulation [8, 19–22]. It is apparent that the strain well satisfies the needs of converting anaerobic digestate into value-added fuels and chemicals.
Therefore, this study focused on applying M. isabellina to utilize anaerobic digestate (both solid digestate and liquid digestate) for lipid accumulation, and integrating the fungal fermentation with AD to achieve an energy-positive and fresh-water-free process of lignocellulosic biodiesel production. Meanwhile, the studied process also contributes to development of next-generation organic waste management strategies that turn current treatment-based practices into future utilization-based practices. A win–win solution would be thus achieved for both biofuel production and waste management.
Methods
Feedstock characteristics
Anaerobic digestion effluent (after the digestion), liquid digestate (after liquid/solid separation), and solid digestate (after liquid/solid separation) were collected from the Michigan State University (MSU) South Campus Anaerobic Digester (42.698800, −84.488068). The digester is a completely stirred tank reactor (CSTR). The effective volume of the digester is 1570 m3. The feed of the digester consisted of animal manure from the MSU dairy farm and food wastes from the MSU cafeteria and a nearby food processing facility. The manure and food wastes were mixed at a dry matter ratio of 1.3:2. The characteristics of the mixed feed are listed in Table 1. The digestion temperature and retention time were 40 °C and 25 days, respectively. The biogas is combusted by a 400 kW MAN biogas engine to produce electricity and heat. The digestion performance data are listed in Table 1 as well.
After the digestion, a commercial screw press separator with 2 mm screen was used to carry out the liquid/solid separation of the AD effluent. The liquid digestate and solid digestate were obtained accordingly. The characteristics of the AD effluent, liquid digestate, and solid digestate are listed in Table 2.
Dilute alkali pretreatment and enzymatic hydrolysis of the digestates
It has been reported that alkali treatment was more efficient to pretreat solid digestate than other treatment methods [23]. Therefore, the solid digestate rich in cellulose, hemicellulose, and lignin was pretreated by a dilute alkali treatment with the conditions of 120 °C for 2 h and a sodium hydroxide (NaOH) concentration of 2% (w/w) using liquid digestate as the processing water. The pretreatment was carried out in 125 mL glass bottles (Wheaton Industries, Millville, NJ), and placed in an autoclave (Brinkmann 2540 M; Tuttnauer USA Co. Ltd., Hauppauge, NY). The effective volume of the slurry in the bottle was 50 mL. The TS of the pretreatment slurry was adjusted to 10% by adding the liquid digestate. After the dilute alkali pretreatment, the pretreated slurry was adjusted to a pH of 5.0 ± 0.2 using 20% (w/w) sulfuric acid (H2SO4). An enzyme mixture consisting of 9.10 mg cellulase (CTEC 3, protein content: 218 mg/mL; Novozymes North America, Franklinton, NC) and 1.43 mg xylanase (HTEC 3, protein content: 171 mg/mL; Novozymes North America, Franklinton, NC) per gram dry matter of the solid digestate was applied on the pretreated slurry to carry out the enzymatic hydrolysis at 50 °C and 150 rpm (2.5 Hz) in a shaking incubator (Thermo Scientific, Odessa, TX) for 72 h. After the enzymatic hydrolysis, the hydrolysate was centrifuged at 7025g for 10 min to separate the liquid hydrolysate from the residual solids. Approximately 2 mL of the liquid hydrolysate was filtered through a 0.22 µm polyethersulfone membrane filter for sugar analysis. The remaining liquid hydrolysate was used for the following detoxification and fermentation tests.
Overliming detoxification
A completely randomized design (CRD) was adopted to elucidate the effects of overliming conditions (detoxification time and temperature) on sugar recovery and fermentation performance. Three detoxification times (1, 5, and 16 h) and two temperatures (30 and 50 °C) formed six treatments, and each treatment had three replicates, which led to a total of eighteen runs. The detoxification was carried out in 500 mL media bottles (Wheaton Industries, Millville, NJ). Ca(OH)2 was added in the liquid hydrolysate until the pH reached 10. The bottles were placed in a shaking incubator (Thermo Scientific, Odessa, TX) at 150 rpm (2.5 Hz) according to the targeted detoxification time and temperature.
After detoxification, the pH of the detoxified hydrolysate was adjusted back to 6 using 20% (w/w) H2SO4. The detoxified hydrolysate was centrifuged at 7025g for 10 min to separate the liquid hydrolysate from the residues. Approximately 2 mL of the hydrolysate was filtered through a 0.22-µm polyethersulfone membrane filter for sugar analysis. The remaining detoxified liquid hydrolysate was stored in the −20 °C freezer for the following fermentation test.
Oleaginous fungal fermentation
Fungal fermentation to evaluate the effects of overliming detoxification
Mortierella isabellina ATCC 42613 was used to accumulate lipids on the detoxified hydrolysate medium. The spore and seed cultures were prepared according to methods described by previous studies [20, 24]. The fermentation was carried out in 250 mL Erlenmeyer flasks containing 80 mL of the medium. The detoxified hydrolysate served as the fermentation media. The raw hydrolysate and a synthetic solution containing glucose, xylose, and acetate in concentrations similar to those found in the hydrolysate were used as controls. All media were supplemented with yeast extract (DOT Scientific Inc., Burton, MI) and mineral salts. The yeast extract concentration in the media was 2.0 g/L. The mineral salts in the media were 1 g/L KH2PO4, 0.5 g/L MgCl2·6H2O, 0.0014 g/L ZnSO4·7H2O, 0.0016 g/L MnSO4·H2O, 0.0036 g/L CoCl2·6H2O, and 0.00275 g/L FeSO4·7H2O. All fermentation media were adjusted to pH 6.0 using 20% (w/w) H2SO4 solution or 30% (w/w) NaOH solution before being sterilized at 121 °C for 15 min. The fermentation medium was inoculated with 10% (v/v) seed and cultivated for 90 h at 25 ± 1 °C on a shaking incubator at 180 rpm (3 Hz).
Kinetics of batch fungal fermentation on the selected detoxified hydrolysate
The same dilute alkali pretreatment and enzymatic hydrolysis described in 2.2 was applied on the anaerobic digestate to prepare the hydrolysate. 500 mL flasks containing 200 mL of the digestate slurry were used to carry out the pretreatment and hydrolysis. The selected detoxification method was applied to detoxify the hydrolysate for the batch fungal fermentation. The supplemental nitrogen and mineral salts and inoculation and culture conditions were the same as those described in “Fungal fermentation to evaluate the effects of overliming detoxification” section. The culture was carried out in 500 mL Erlenmeyer flasks containing 200 mL of the medium. The batch fermentation duration was 77 h. Samples were taken along cultivation for sugar, acetate, and fungal biomass analyses. Three replicates were run for this experiment.
Kinetics of repeated-batch fungal fermentation on the selected detoxified hydrolysate
The same dilute alkali pretreatment, enzymatic hydrolysis, and detoxification described in “Fungal fermentation to evaluate the effects of overliming detoxification” section were used on the anaerobic digestate to prepare the detoxified hydrolysate for the repeated-batch fungal fermentation. The supplemental organic nitrogen and mineral salts along with inoculation and culture conditions were the same as described in “Fungal fermentation to evaluate the effects of overliming detoxification” section. The culture was carried out in 500 mL Erlenmeyer flasks containing 100 mL of the medium. Once the carbon sources were nearly depleted, the fungal biomass was sterilely separated from the fermentation broth by settling the flasks for 30 min. The supernatant was poured out, and the fresh medium was added to the flasks to carry out the next batch. The operation was repeated twice at 100 and 190 h. Five fermentation broth samples and one fungal biomass sample were collected from each stage for sugar, acetate, biomass and lipid analyses.
Mass and energy balance
Mass and energy balance analysis was carried out based on 1000 kg dry mixed feed for the anaerobic digestion. The target system included both anaerobic digestion and fungal fermentation of lipid accumulation. The performance data of the MSU CSTR digester were used to conclude the mass and energy balance of the anaerobic digestion operation. The data from the aforementioned hydrolysis, detoxification, and fermentation experiments were used for the mass and energy balance of the lipid production on the digestate according to a reported method [25].
Analytical methods
COD, TP, and TN were determined using HACH kits (product number: 2125915, 2767245 and 2714100, HACH Company, Loveland, CO). TS and VS were analyzed according to APHA [26]. Elemental analysis of the AD fiber was conducted using an element analyzer (ECS 4010, Costech Analytical Technologies Inc., Valencia, CA) in the MSU Soil Biology Lab. Fiber composition of the solid digestate was measured following the Laboratory Analytical Procedure (LAP) developed by the National Renewable Energy Laboratory (NREL) [27].
Glucose, xylose, and acetate in the hydrolysate and fermentation media were determined by high performance liquid chromatography (HPLC) (Shimadzu Corp., Kyoto, Japan) equipped with an analytical column (Aminex HPX-87H, Bio-Rad Laboratories, Inc., Hercules, CA) and a refractive index detector (Shimadzu Corp., Kyoto, Japan). The mobile phase was 0.005 mol/L sulfuric acid at a flow rate of 0.6 mL/min. The oven temperature was set at 65 °C. HPLC-grade standards including glucose, xylose, and sodium acetate were purchased from Sigma (Sigma–Aldrich, St. Louis, MO).
Fungal biomass was collected by filtration and washed three times with deionized water. Cell biomass was determined by drying at 105 °C until a constant weight was achieved. The dried cell biomass was ground in a mortar for lipid extraction. Total lipid was determined gravimetrically [28].
Statistical analysis
A two-way ANOVA using the Statistical Analysis System 9.0 (SAS Institute Inc., Cary, NC) was carried out to analyze the significance of impacts of two detoxification factors on sugar recovery and fermentation performance. A pair-wise comparison using SAS 9.0 was also conducted to identify significant differences between experimental runs.
Results and discussion
Characteristics of AD effluent, solid digestate, and liquid digestate
The characteristics of the AD effluent, solid digestate, and liquid digestate indicate that the solid digestate was the only stream that has both desirable TS content (30.60%) and carbohydrate contents (26, 13, and 30% of cellulose, xylan, and lignin, respectively) to be used as the lignocellulosic feedstock for fungal lipid accumulation (Table 2). In addition, the liquid digestate contained a significant amount of nitrogen and phosphorus (1900 and 810 mg/L, respectively), which represents a potential nutrient stream to support the fungal fermentation. Liquid and solid digestates can be mixed to achieve desirable TS, carbohydrate, and nutrient contents for different microbial processes. In this study, the TS content of the mixture feed was set at 10% to carry out pretreatment, hydrolysis, and fermentation based on previous M. isabellina studies on lignocellulosic materials [8, 20, 29].
Effects of overliming detoxification on sugar recovery and fungal fermentation
After pretreatment and hydrolysis, the mixture feed at the TS of 10% generated a hydrolysate containing 13.85 g/L of glucose, 8.95 g/L of xylose, and 2.67 g/L of acetate. The effects of different detoxification conditions on sugar and acetate concentrations in the hydrolysate are demonstrated in Fig. 1. The pair-wise comparison concluded that there were no significant (P > 0.05) differences on sugar and acetate concentrations between non-detoxified and detoxified hydrolysates. This result indicates that the tested overliming conditions did not lead to significant substrate loss in hydrolysates, which was different from other overliming treatment studies on hydrolysates from bagasse and other lignocellulosic materials [16, 30].
To further evaluate effects of the overliming on fungal fermentation, the hydrolysates from different detoxification conditions were used to carry out M. isabellina cultivation. The substrate consumption of M. isabellina on the hydrolysates are presented in Fig. 2. Sugars and acetate were not consumed in the hydrolysate without detoxification during the 89 h culture period (Fig. 2b). The lack of sugar consumption clearly demonstrates a strong inhibitory effect of the alkali pretreated hydrolysate on M. isabellina. Detoxification is necessary to make the hydrolysate amendable to the fungal strain. With overliming detoxification, the sugars and acetate were completely consumed in 89 h of fermentation for all hydrolysates under different overliming conditions, which indicates that the detoxification did effectively alleviate the inhibitory effect of the hydrolysates on the fungal strain. However, compared to the culture on the synthetic medium (all sugars and acetate were consumed in 66 h), a delay (23 h) of substrate consumption was observed from the cultures on detoxified hydrolysates (Fig. 2c–h).
To determine the preferred detoxification condition, lipid production was used to statistically compare the effects of detoxification conditions on fungal fermentation (Table 3). M. isabellina on the synthetic medium consumed all substrates and generated 3.69 g/L lipid. Compared to the culture on the synthetic medium, the cultures on the detoxified hydrolysates overall produced less lipid. The accumulated lipid and lipid productivities of the cultures on the detoxified hydrolysates ranged from 1.52 to 3.48 g/L and from 0.41 to 0.94 g/L/d, respectively. The corresponding lipid-substrate conversion were between 0.07 and 0.16 g/g. The two-way ANOVA elucidates that both detoxification temperature and time did significantly (P < 0.05) influence the lipid concentration, lipid-substrate conversion, and lipid productivity. The pair-wise comparison concludes that the detoxification conditions of 30 °C and 5 h had significantly (P < 0.05) better performance on fungal lipid accumulation (Table 3), in which lipid concentration, lipid-substrate conversion, and lipid productivity reached 3.48 g/L, 0.16 g/g, and 0.94 g/L/d, respectively. Therefore, 30 °C and 5 h was selected as the preferred detoxification method.
Fungal lipid accumulation on the selected detoxified hydrolysate
The effect of the preferred detoxification on fungal fermentation of biomass and lipid accumulation was then investigated. A batch fungal fermentation on the selected detoxified hydrolysate (under the detoxification conditions of 5 h and 30 °C) was performed (Fig. 3). The substrate consumption kinetics were very similar to the cultures in “Effects of overliming detoxification on sugar recovery and fungal fermentation” section. The glucose and acetate were completely consumed in 49–54 h, respectively. At the end of batch culture (77 h), 1.79 g/L xylose remained in the broth, and 8.98 g/L biomass and 1.50 g/L lipid were accumulated. The corresponding lipid and biomass yields were 0.07 and 0.42 g/g, respectively (Table 4).
Due to relatively low carbohydrate content (26.52% cellulose and 13.31% xylan) in the solid digestate (Table 2), the biomass and lipid concentrations were relatively low from the batch culture. Lipid concentration is a very important parameter for downstream separation and extraction as well as the process economics, thus methods for improvement should be investigated. Since lipid is a structural component of fungal biomass, accumulating more biomass substantially and directly leads to higher lipid concentration. Therefore, a repeated-batch fermentation culture, a common approach to enhance the biomass accumulation [31, 32], was adopted to improve the fermentation performance of fungal biomass and lipid production. Kinetics of the repeated-batch fermentation is shown in Fig. 4. The trends of substrate consumption, fungal biomass, and lipid accumulation were similar to the batch culture; however, the substrate consumption rates dramatically increased from the initial batch to the 2nd repeated batch, and so on. The glucose consumption rates were 4.68, 9.32 and 19.37 g/L/d, the corresponding acetate consumption rates were 1.15, 1.84, and 4.06 g/L/d, and the xylose consumption rates were 0.77, 1.04, and 1.12 g/L/d in the initial batch, 1st repeated-batch, and 2nd repeated-batch, respectively. The substantial increase in the substrate consumption rate in subsequent stages of fermentation may be explained by continuous accumulation of the fungal biomass. Higher biomass concentration in the late stages demands more nutrients, which leads to a higher substrate consumption rate. In addition, it is also possible that the fungal strain was gradually ‘trained’ during the repeated-batch fermentation to adapt to the ‘harsher’ culture environment so that the lag time was significantly shortened in the later stages. Further investigations are needed to draw an accurate conclusion.
Biomass and lipid accumulation kinetics also demonstrate that the biomass concentrations significantly increased from 6.74 g/L in the initial batch to 11.11 g/L in the 1st repeated-batch and 14.34 g/L in the 2nd repeated-batch (Fig. 4; Table 4). The lipid concentrations correspondingly changed from 1.25 to 2.17 to 3.16 g/L (Table 4). The lipid contents in the biomass also increased from 0.17 to 0.20 to 0.21 g/g while the lipid yields remained at approximately 0.07 g/g for all three stages during the repeated-batch culture. The biomass yields were reduced from 0.45 to 0.36 to 0.31 g/g. An increase in metabolism in the later stages of the culture, leading to more substrate oxidation (generating energy and carbon dioxide) than substrate assimilation (accumulating biomass and metabolites), may provide an explanation for the decrease in biomass yields over the course of cultivation. At the end of the repeated-batch fermentation, the biomass and lipid concentrations reached 14.36 and 3.16 g/L, respectively, which were 1.60 and 2.11 times more than the corresponding concentrations (8.98 and 1.50 g/L) from the batch culture (Table 4).
Even though the repeated-batch culture significantly enhanced biomass and lipid production, lipid yields were still lower compared to the previous studies using lignocellulosic materials [8, 19, 20, 33]. Zhong et al. reported a lipid yield of 0.15 g/g cultured on the hydrolysate from a mixture of corn stover and solid digestate [8]. Ruan et al. reported lipid yields of 0.12, 0.15, 0.13, and 0.10 g/g on the hydrolysates from corn stover, switchgrass, miscanthus, and giant reed, respectively [20]. The low lipid yield in this study was probably caused by the low C/N ratio. The C/N ratios of the hydrolysates used for the fungal cultivation ranged from 2.16 to 3.07 (Table 4), which were several magnitudes lower than the reported ratios. It has been reported that oleaginous organisms tend to accumulate more lipids under nitrogen limited culture conditions [24, 34]. The typical C/N mole ratios used for M. isabellina culture of lipid accumulation were in the range of 60–300 [24]. Therefore, it is apparent that adjusting C/N ratio of the hydrolysate from digestates is critical to further improve fungal lipid yield.
Mass and energy balance analysis
A mass and energy balance was conducted to evaluate the system performance (Fig. 5). The AD generates 169 kg methane, 1700 kg wet solid digestate, and 9971 kg liquid digestate per 1000 kg dry mixed feed to the digester (Fig. 4). A portion of the liquid digestate (4382 kg) was mixed with 1700 kg wet solid digestate to prepare the anaerobic digestate with 10% TS for hydrolysis/detoxification and fungal fermentation. The remaining liquid digestate (5589 kg/1000 kg dry mixed feed) rich in nitrogen and phosphorus can be used as a liquid fertilizer for crop production. The hydrolysis and detoxification applying three unit operations of NaOH pretreatment, enzymatic hydrolysis, and Ca(OH)2 detoxification generated a hydrolysate (4511 kg) that contained 66 kg glucose, 42 kg xylose, and 13 kg acetate. The hydrolysis and detoxification also generated 1668 kg wet solid residue rich in lignin (containing 157 kg lignin). The wet solid residue after drying can be used as the solid fuel for energy production. The repeated-batch fungal fermentation on the hydrolysate produced 38 kg dry fungal biomass with 23% lipid. The mass balance results also demonstrate that the liquid digestate provided enough water to satisfy the water demand of the process, which addresses one of the major challenges—a large amount of fresh water needed for fermentation processes of biofuel and chemical production [35–38].
Mass balance of the fungal lipid production on anaerobic digestate including both anaerobic digestion and fungal fermentation. a The glucose, xylose, and acetate concentrations of 13.85, 8.95 and 2.67 g/L were used for the calculation. b The biomass and lipid conversion (0.31 and 0.07 g/g substrates) from the repeated-batch operation were used to calculate the fungal biomass and lipid production. c The dry matter of the wet biomass was 25%
Energy balance shows that integrating AD and fungal fermentation leads to an energy-positive system of fungal lipid production (Table 5). Based on 1000 kg dry mixed feed, AD as a power unit in the system generated a net energy of 6478 MJ. The hydrolysis and detoxification operation consumed 1593 MJ. The hydrolysis residue rich in lignin can produce 3830 MJ, which led to a positive energy output of 2237 MJ for the hydrolysis and detoxification operation. The fungal fermentation as an aerobic cultivation process was the most energy-intensive unit operation in the system. It required 9048 MJ to complete the fermentation. 8.6 kg lipid from 38 kg dry fungal biomass had an energy content of 344 MJ. Due to energy production from biogas and lignin, a positive overall net energy of 11.09 MJ was achieved by the integrated system.
Based on the mass and energy balance analysis, a self-sustaining process to produce lipid from anaerobic digestate has been realized by combining AD and aerobic fungal fermentation. The results also indicate that improving hydrolysis (the current conversion of cellulose and xylan to glucose and xylose were only 47 and 64%, respectively) and fermentation (the lipid yield was only 0.07 g per g substrates) efficiencies could significantly enhance the system performance of lipid production. The related studies are currently being carried out in the authors’ labs.
Conclusions
A fresh-water-free and energy-positive process was developed in this study to simultaneously utilize both solid and liquid digestates to accumulate fungal lipids for biodiesel production. The mixture of solid and liquid digestates was pretreated and hydrolyzed by alkali and enzyme, respectively, to release mono-sugars. The subsequent overliming detoxification process was then applied to prepare the hydrolysate for fungal fermentation. The repeated-batch fungal cultivation significantly increased biomass and lipid concentrations. The methane production in the AD operation provided the energy for the fungal lipid accumulation on the digestate, which leads to an energy-positive process using aerobic fermentation for production of fuel precursor. The results clearly demonstrate that the studied process has potential to be a win–win solution for both biofuel production and waste management.
Abbreviations
- AD:
-
anaerobic digestion
- COD:
-
chemical oxygen demand
- CSTR:
-
completely stirred tank reactor
- TS:
-
total solids
- CRD:
-
completely randomized design
- TP:
-
total phosphorus
- TN:
-
total nitrogen
- C/N:
-
carbon:nitrogen
References
Campbell JE, Lobell DB, Field CB. Greater transportation energy and GHG offsets from bioelectricity than ethanol. Science. 2009;324(5930):1055–7.
Noike T, Goo IS, Matsumoto H, Miyahara T. Development of a new type of anaerobic digestion process equipped with the function of nitrogen removal. Water Sci Technol. 2004;49(5–6):173–9.
Nizami AS, Korres NE, Murphy JD. Review of the integrated process for the production of grass biomethane. Environ Sci Technol. 2009;43(22):8496–508.
AgStar. Continued growth in digester projects. Washington D.C.: US-EPA; 2010.
Tambone F, Genevini P, D’Imporzano G, Adani F. Assessing amendment properties of digestate by studying the organic matter composition and the degree of biological stability during the anaerobic digestion of the organic fraction of MSW. Biores Technol. 2009;100(12):3140–2.
Teater C, Yue ZB, MacLellan J, Liu Y, Liao W. Assessing solid digestate from anaerobic digestion as feedstock for ethanol production. Biores Technol. 2011;102(2):1856–62.
Mohan SV, Mohanakrishna G, Chiranjeevi P, Peri D, Sarma PN. Ecologically engineered system (EES) designed to integrate floating, emergent and submerged macrophytes for the treatment of domestic sewage and acid rich fermented-distillery wastewater: evaluation of long term performance. Biores Technol. 2010;101(10):3363–70.
Zhong Y, Ruan ZH, Zhong YK, Archer S, Liu Y, Liao W. A self-sustaining advanced lignocellulosic biofuel production by integration of anaerobic digestion and aerobic fungal fermentation. Biores Technol. 2015;179:173–9.
Jonsson LJ, Martin C. Pretreatment of lignocellulose: formation of inhibitory by-products and strategies for minimizing their effects. Biores Technol. 2016;199:103–12.
Yang B, Wyman CE. Pretreatment: the key to unlocking low-cost cellulosic ethanol. Biofuels Bioprod Biorefining. 2008;2(1):26–40.
Alriksson B, Sjode A, Nilvebrant N-O, Jonsson LJ. Optimal conditions for alkaline detoxification of dilute-acid lignocellulose hydrolysates. Appl Biochem Biotechnol. 2006;129–132:599–611.
Cavka A, Jonsson LJ. Detoxification of lignocellulosic hydrolysates using sodium borohydride. Biores Technol. 2013;136:368–76.
Cannella D, Sveding PV, Jorgensen H. PEI detoxification of pretreated spruce for high solids ethanol fermentation. Appl Energy. 2014;132:394–403.
Jonsson LJ, Alriksson B, Nilvebrant N-O. Bioconversion of lignocellulose: inhibitors and detoxification. Biotechnol Biofuels. 2013;6:1.
Millati R, Niklasson C, Taherzadeh MJ. Effect of pH, time and temperature of overliming on detoxification of dilute-acid hydrolyzates for fermentation by Saccharomyces cerevisiae. Process Biochem. 2002;38(4):515–22.
Martinez A, Rodriguez ME, York SW, Preston JF, Ingram LO. Effects of Ca(OH)(2) treatments (“overliming”) on the composition and toxicity of bagasse hemicellulose hydrolysates. Biotechnol Bioeng. 2000;69(5):526–36.
Nkoa R. Agricultural benefits and environmental risks of soil fertilization with anaerobic digestates: a review. Agron Sustain Dev. 2014;34(2):473–92.
Yeh S, Berndes G, Mishra GS, Wani SP, Neto AE, Suh S, Karlberg L, Heinke J, Garg KK. Evaluation of water use for bioenergy at different scales. Biofuels Bioprod Biorefining. 2011;5(4):361–74.
Ruan ZH, Zanotti M, Wang XQ, Ducey C, Liu Y. Evaluation of lipid accumulation from lignocellulosic sugars by Mortierella isabellina for biodiesel production. Biores Technol. 2012;110:198–205.
Ruan ZH, Zanotti M, Zhong Y, Liao W, Ducey C, Liu Y. Co-hydrolysis of lignocellulosic biomass for microbial lipid accumulation. Biotechnol Bioeng. 2013;110(4):1039–49.
Ruan ZH, Zanotti M, Archer S, Liao W, Liu Y. Oleaginous fungal lipid fermentation on combined acid- and alkali-pretreated corn stover hydrolysate for advanced biofuel production. Biores Technol. 2014;163:12–7.
Ruan ZH, Hollinshead W, Isaguirre C, Tang YJJ, Liao W, Liu Y. Effects of inhibitory compounds in lignocellulosic hydrolysates on Mortierella isabellina growth and carbon utilization. Biores Technol. 2015;183:18–24.
Yue ZB, Teater C, Liu Y, MacLellan J, Liao W. A sustainable pathway of cellulosic ethanol production integrating anaerobic digestion with biorefining. Biotechnol Bioeng. 2010;105(6):1031–9.
Ruan Z, Zanotti M, Wang X, Ducey C, Liu Y. Evaluation of lipid accumulation from lignocellulosic sugars by Mortierella isabellina for biodiesel production. Bioresour Technol. 2012;110:198–205.
Zanotti M, Ruan ZH, Bustamente M, Liu Y, Liao W. A sustainable lignocellulosic biodiesel production integrating solar- and bio-power generation. Green Chem. 2016;18(18):5059–68.
APHA. Standard methods for the examination of water and wastewater. Washington, D.C.: American Public Health Association; 1998.
Sluiter JB, Ruiz RO, Scarlata CJ, Sluiter AD, Templeton DW. Compositional analysis of lignocellulosic feedstocks. 1. review and description of methods. J Agric Food Chem. 2010;58(16):9043–53.
Bligh EG, Dyer WJ. A rapid method of total lipid extraction and purification. Can J Biochem Physiol. 1959;37(8):911–7.
Ruan Z, Zanotti M, Archer S, Liao W, Liu Y. Oleaginous fungal lipid fermentation on combined acid- and alkali-pretreated corn stover hydrolysate for advanced biofuel production. Bioresour Technol. 2014;163:12–7.
Larsson S, Reimann A, Nilvebrant NO, Jonsson LJ. Comparison of different methods for the detoxification of lignocellulose hydrolyzates of spruce. Appl Biochem Biotechnol. 1999;77–9:91–103.
Pan JG, Rhee JS, Lebeault JM. Physiological constraints in increasing biomass concentration of Escherichia-coli-b in fed-batch culture. Biotechnol Lett. 1987;9(2):89–94.
Costa JAV, Colla LM, Duarte PF. Improving Spirulina platensis biomass yield using a fed-batch process. Biores Technol. 2004;92(3):237–41.
Co A. Average digester capital cost per cow. Ferndale: Andgar corporation; 2008.
Ratledge C. Fatty acid biosynthesis in microorganisms being used for single cell oil production. Biochimie. 2004;86(11):807–15.
Wu M, Mintz M, Wang M, Arora S. Consumptive water use in the production of bioethanol and petroleum gasoline. Chicago: Center for Transportation Research, Energy Systems Division, Argonne National Laboratory; 2008.
Subhadra BG, Edwards M. Coproduct market analysis and water footprint of simulated commercial algal biorefineries. Appl Energy. 2011;88(10):3515–23.
Fingerman KR, Torn MS, O’Hare MH, Kammen DM. Accounting for the water impacts of ethanol production. Environ Res Lett. 2010;5(1):014020.
Martín M, Ahmetovic E, Grossmann IE. Optimization of water consumption in second generation bioethanol plants. Ind Eng Chem Res. 2010;50(7):3705–21.
Authors’ contributions
YZ, ZL, CI, YL, and WL conceived and designed the study, analyzed and interpreted data, and wrote the manuscript. YZ, ZL, CI, and YL conducted experiments. All authors read and approved the final manuscript.
Acknowledgements
The authors would like to thank the AgBioResearch at Michigan State University for funding this work through faculty salaries. The authors also like to thank Dr. Dana Kirk and Mr. Louis Faivor to provide the data of the MSU campus anaerobic digestion operation.
Competing interests
The authors declare they have no competing interests.
Availability of supporting data
Data will be made available upon request.
Consent for publication
All authors approved the manuscript.
Funding
This study is funded by the AgBioResearch at Michigan State University.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.
About this article
Cite this article
Zhong, Y., Liu, Z., Isaguirre, C. et al. Fungal fermentation on anaerobic digestate for lipid-based biofuel production. Biotechnol Biofuels 9, 253 (2016). https://doi.org/10.1186/s13068-016-0654-3
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13068-016-0654-3