Abstract
Nickel oxide (NiO) and phosphotungstic acid (PTA) supported on a ZIF-8 (NiO-PTA/ZIF-8) catalyst was first synthesized and it showed high activity and good selectivity for the hydrocracking of Jatropha oil. The catalyst was characterized by SEM, SEM-EDS, TEM, N2 adsorption, FT-IR, XRD and XPS. Compared with the NiO-PTA/Al2O3 catalyst, the selectivity of C15-C18 hydrocarbon increased over 36%, and catalytic efficiency increased 10 times over the NiO-PTA/ZIF-8 catalyst. The prepared NiO-PTA/ZIF-8 catalyst was stable for a reaction time of 104 h and the kinetic behavior was also analyzed. This catalyst was found to bypass the presulfurization process, showing promise as an alternative to sulfided catalysts for green diesel production.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
As global fossil fuel reserves diminish, there is a pressing need to develop renewable liquid fuels that are environmentally friendly1. Biofuels such as green diesel produced by hydroprocessing of plant oils typically display similar properties to petroleum diesel. They can be directly used in existing infrastructures with no modifications2. Various porous sulfided catalysts have been used to produce biofuels from plant oils3. NiMo4,5,6,7, CoMo8,9,10, Pt11,12 and Pd13,14 based catalysts with porous SiO2-Al2O315,16 and zeolites17,18 support have been used for hydrotreating of plant oils19. These catalysts were successfuly used to convert renewable feedstocks into green diesel, stimulating exploration of the potential of other porous materials as catalysts. Due to their high specific area and porosity20,21,22,23, metal organic frameworks (MOFs) are appealing candidates for this type of conversion.
The selection of MOF supports significantly affects catalytic activity and product selectivity24,25,26,27. Zeolitic imidazolate frameworks (ZIFs)28,29,30, a subfamily of MOFs, is a microporous material with uniform small pores. A number of ZIFs exhibit permanent porosity, as well as a thermal and chemical stability31,32. The prototype system ZIF-8 has been proposed as a promising material in adsorption/separation33,34 and as a heterogeneous catalyst35. It has been reported that ZIF-8 showed excellent catalytic activity and selectivity for transesterification of DMC with DEC36, and catalyze transesterification of vegetable oil with significant activity37. ZIF-8 was also used as a catalyst for Friedel-Crafts acylation of anisole with benzoyl chloride and the reaction afforded a selectivity of 93–95% to the p-isomer38.
The design and preparation of several catalysts in ZIF-8 supported monometallic or bimetallic nanoparticles have been reported, since metal nanoparticles supported on ZIF-8 show improved catalytic activity and selectivity39,40. For example, Pd@ZIF-8 exhibitd excellent catalytic activity toward the catalytic reduction of p-nitrophenol to p-aminophenol in the presence of NaBH4 at room temperature41. Hydrogen reduction and CO oxidation of Au/ZIF-8 was performed to verify the structural stability of the framework under common preparation and application conditions used for supported metal catalysts42. The Fe3O4@ZIF-8 catalyst exhibited fair separation ability and reusability, which can be repeatedly applied for Knoevenagel condensations and Huisgen cycloadditions for at least ten successive cycles43. The NiRh supported on nitrogen-doped porous carbon (NPC) derived from ZIF-8 were synthesized and exhibited the highest catalytic activity and 100% hydrogen selectivity toward hydrogen generation from hydrazine44. The Pd/ZIF-8-derived carbon catalyst exerts extremely high catalytic activity and electrochemical stability for methanol electrooxidation45. Tuan T. Dang et al.46 reported PdNPs/ZIF-8 was a efficient heterogeneous catalyst for the aminocarbonylation of bromoarenes.
The high surface area and narrow pore distribution of ZIF-8 may lead to uniform distribution of highly dispersed nanoparticles, which may control catalytic activity and selectivity47. For example, when Pd, Pt, Ru, and Ir nanoparticles supported on ZIF-8 were applied to the hydrogenation reaction, they showed high activity and selectivity48. Guang Lu et al.35 reported that Pt, Fe2O3 and CdTe nanoparticles supported on ZIF-8 exhibited catalytic, magnetic and photoluminescence properties, respectively. Hailong Jiang et al.49 found that Au@Ag/ZIF-8 exhibited a strong bimetallic synergistic effect and high catalytic activity. Chao Hou et al.50 synthesized Rh@ZIF-8, a highly efficient catalyst in the hydroformylation of alkenes. Peizhou Li et al.51 prepared highly dispersed Ni NPs immobilized on ZIF-8 (Ni/ZIF-8) and examined catalytic activity of hydrogen generation in the hydrolysis of ammonia borane. It is interesting to note that turnover frequency (TOF) values obtained for Ni/ZIF-8 are among the highest values for Ni catalysts ever reported52. However, there is little or no research on transition metals supported on ZIF-8 as a catalyst for hydrocracking of Jatropha oil.
Some literature has obtained encapsulation of phosphotungstic acid (PTA) into the MOF, such as MIL-10153, MIL-100(Fe)54, HKUST-1 Cu3(BTC)255 and Fe-EMOF56. In our previous work, we found that PTA combined with Ni/Al2O3, Ni/hydroxyapatite and flower-like NiO can be used as effective bifunctional catalysts for the hydrocracking of plant oil57,58,59. The PTA supplies the metal sites (W oxide species) and also provides acid sites for isomerization. Since nonedible Jatropha oil has many advantages, including high oil production at a low price and high energy density60,61, in this study, we prepared NiO and PTA supported on ZIF-8 as an efficient catalyst for hydrocracking of Jatropha oil. Results show that these catalysts exhibit high catalytic activity, good selectivity, and can prevent sulfurization and its effects on the environment and human health.
Methods
Synthesis of NiO-PTA/ZIF-8 catalyst
Figure 1 displays the synthetic procedure of NiO-PTA/ZIF-8 catalyst. Blank ZIF-8 nanocrystals were synthesized according to Christoph Rösler et al.62. Typically, Zn(NO3)2·6H2O (2.0 g) was added into 40 mL methanol and stirred until it was completely dissolved. Next, 2-methylimidazole (2.0 g) was added into the above solutions and stirred. After 10 min, a white suspension began to form, which was maintained at 25 °C and stirred for a total synthesis time of 2 h. Finally, the mixture was kept at 60 °C for 12 h without stirring. The white precipitates were collected by centrifuging and washed with methanol three times. Nickel nitrate and phosphotungstic acid (PTA) was introduced into the ZIF-8 with an impregnation method. The synthesized ZIF-8 was dried under a vacuum at 150 °C for 5 h and quickly added to a solution of Ni(NO3)2·6H2O (5 wt%). Then the NiO/ZIF-8 was prepared by calcination in a muffle oven at 400 °C for 4 h. Finally, a NiO-PTA/ZIF-8 catalyst was obtained by impregnanting NiO/ZIF-8 with an aqueous solution of H3O40PW12. We set the PTA loading amount 30%, which was confirmed as the suitable PTA loading amount for hydrocracking by our previous work63. Impregnated samples were calcined at 200 °C for 3 h.
The NiO-PTA/Al2O3 catalyst was used to compare with NiO-PTA/ZIF-8 catalyst, which was also prepared by wet impregnation. First, the NiO/Al2O3 was prepared by impregnating aqueous solutions of Ni(NO3)2·6H2O (5 wt%) on a commercial Al2O3 (diameter 0.2–0.3 mm). Impregnated samples were dried overnight at 105 °C and calcined at 400 °C for 4 h. The NiO-PTA/Al2O3 catalyst was prepared by impregnating the Ni/Al2O3 catalyst with a solution containing 30 wt% PTA. Impregnated samples were calcined at 200 °C for 3 h.
Characterization of NiO-PTA/ZIF-8 catalyst
Samples were examined under a scanning electron microscope (SEM, Hitachi S-4800) and transmission electron microscope (TEM, JEM-1010). The EDS-mapping (Energy-dispersive X-ray spectroscopy) was performed on a SU8010 instrument (Hitachi High-Tech, Japan). The working parameters of the EDS were: high voltage (HV) 15 kV and work distance (WD) 10 mm, and the sample was sputter coated with gold to reduce charging effects. Nitrogen adsorption-desorption isotherms were carried out a V-Sorb 2800 TP Surface Area and Pore Distribution Analyzer instrument. Before gas analysis, the samples were evacuated for 4 h at 300 °C under a vacuum. The surface area of the samples was estimated using the Brunauer-Emmett-Teller (BET) equation. The total pore volume (Vtotal) was determined using the adsorption branch of the N2 isotherm at P/P0 = 0.99, and the micropore volume (Vmicro) was calculated using the t-plot method. The size distribution was obtained by the Barrett-Joyner-Halenda (BJH) method by analyzing the adsorption branch of the isotherm. Fourier transform infrared (FT-IR) spectra were recorded using KBr pellets on GANGDONG FTIR-650 ranging from 400 to 4000 cm−1 at 1.5 cm−1 resolution averaging 32 scans. X-ray diffraction (XRD) patterns were recorded on a Bruker D8 Advance X-ray powder diffractometer with Cu Kα radiation (40 mA and 40 kV), over an angular range from 5° to 60°, a scan rate of 2° per minute, and with a step size of 0.02°. X-ray photoelectron spectroscopy (XPS) data was performed on an ESCALab250 electron spectrometer from Thermo Scientific Corporation with monochromatic 150 W Al Kα radiation. The analysis chamber pressure was about 6.5 × 10−10 mbar. Analysis of peaks was performed with a weighted sum of Lorentzian and Gaussian component curves after background subtraction. Binding energies were calibrated using the C 1 s photoelectron peak at 284.8 eV as a reference.
Catalytic properties
The experimental rig for catalyst testing was basically the same as our previous work64. The catalyst (1.0 g) was packed into a custom designed stainless steel tubular reactor with an inner diameter of 1.2 cm and a length of 56 cm. Prior to the reaction, the catalyst was pretreated by reduction with 3 MPa of H2 at 400 °C for 3 h. Then the reactant Jatropha oil was fed using a high-pressure liquid pump into the reactor. The reaction conditions for the hydrotreatment experiment were as follows: temperature 360 °C, hydrogen pressure 3 MPa, liquid hourly space velocity (LHSV) 9 h−1, and H2/feed 1000 mL/mL. Liquid products were collected in a liquid-gas separator and analyzed by gas chromatograph65,66,67,68,69 (GC-900C) equipped with a capillary column (AT. SE-30, 30 m × 0.25 mm; carrier gas N2) and a flame ionization detector (FID). The product oil (0.2 μL) was loaded onto the column and the following temperature program was used: initial column temp. 60 °C for 2 min, heating rate 15 °C /min to 210 °C, then at 8 °C /min to 270 °C, and at 5 °C /min to 285 °C, with a dwelling time of 5 min at 285 °C. Individual products were identified by GC standards. The conversion of Jatropha oil was calculated as:
![](http://media.springernature.com/lw176/springer-static/image/art%3A10.1038%2Fsrep23667/MediaObjects/41598_2016_Article_BFsrep23667_Equ1_HTML.gif)
where C(TG) is the concentrations of triglycerides (%) in the product oil, determined by GC analysis. The selectivity of C15-C18 hydrocarbon was calculated as:
![](http://media.springernature.com/lw200/springer-static/image/art%3A10.1038%2Fsrep23667/MediaObjects/41598_2016_Article_BFsrep23667_Equ2_HTML.gif)
where Y is the yield of the C15-C18 hydrocarbon (%), determined by GC analysis, and C is the conversion of Jatropha oil (%), calculated with Eq. (1).
Results
Catalyst characterization
As shown in Fig. 2, SEM images confirm the microscopic architecture of the composites. ZIF-8 was homogeneous, with a hexagonal shape, and the average particle size was about 500 nm. There were no obvious aggregations and changes in size and morphology when the NiO-PTA supported on ZIF-8, reflecting their good stability. However, the hexagonal shape of the spent catalyst showed small change, since carbon deposition and crystals significantly aggregated after the reaction.
Energy dispersive X-ray spectroscopy (EDS) was carried out to examine chemical the composition of the NiO-PTA/ZIF-8 catalyst. Figure S1 in the supplementary information shows the expected elemental constituents of Zn, O, Ni, P and W. EDS mapping also reveals that Ni, P and W elements were homogeneously distributed on the ZIF-8 substrate. The estimated Ni, P and W amount was 0.930 atom%, 1.108 atom% and 2.701 atom%, respectively. Compared with fresh catalyst, the Ni, P and W content of spent catalyst was 0.734 atom%, 0.971 atom% and 2.623 atom%, respectively, which decreased slightly after reaction.
To further investigate the morphologies of the ZIF-8 and NiO-PTA/ZIF-8 catalyst, TEM analysis was performed. As shown in Fig. S2A,B (see supplementary information), the ZIF-8 and NiO-PTA/ZIF-8 catalyst both showed the typical hexagonal shape with a particle size around 500 nm, in accordance with that observed in SEM images. This indicates that impregnation of NiO-PTA did not result in an obvious change in particle morphology for ZIF-8 particles. TEM images of the NiO-PTA/ZIF-8 catalyst (Fig. S2C) clearly showed surface clumping of NiO and PTA nanoparticles which form large agglomerated particles. The existing synergistic effects between the NiO-PTA and ZIF-8 support are discussed in the XPS results below.
The surface area and pore distribution of ZIF-8, NiO-PTA/ZIF-8 catalyst and spent NiO-PTA/ZIF-8 catalyst were analyzed using nitrogen adsorption-desorption isotherms (Fig. 3). The isotherms of the three samples (Fig. 3A) showed an abrupt increase at low relative pressure (P/P0 < 0.1), indicating their microporous structure. The pure ZIF-8 displayed typical type-I behavior40. The NiO-PTA/ZIF-8 catalyst and spent NiO-PTA/ZIF-8 catalyst both displayed typical type-IV isotherms with a type H4 hysteresis loop in the range of P/P0 = 0.4–0.8, indicating the presence of mesopores70. It also displayed high adsorption capacities at high relative pressure (P/P0 > 0.8), demonstrating the coexistence of macropores and mesopores71. These findings indicate that the NiO-PTA/ZIF-8 catalyst possesses hierarchically micro-meso-macroporous textures. This may be due to damage to the pores caused by thermal decomposition of the Ni precursor72. Table 1 displays the BET surface area, total pore volume and micropore volume of synthesized ZIF-8 nanoparticles at 1724.19 m2/g, 0.67 cm3/g and 0.58 cm3/g, respectively. Compared with ZIF-8, the NiO-PTA/ZIF-8 catalyst exhibited decreased BET surface area of 611.21 m2/g and a micropore volume of 0.21 cm3/g due to blocking of cavity windows by the deposited NiO and PTA on the surface73. After the reaction, BET surface area and total pore volume of spent NiO-PTA/ZIF-8 catalyst had both decreased. This was likely due to agglomeration of abundant deposited coke, leading to blockage of some micropores and mesopores.
The pore size distributions calculated by the BJH method are shown in Fig. 3B. The pore sizes were narrowly distributed between 1 nm and 5 nm, indicating that ZIF-8 nanoparticles had a highly uniform pore structure. However, the pore size distributions widened, and larger pore diameters distinctly increased after NiO and PTA were added. Macropores formed in the range of 150–300 nm for the NiO-PTA/ZIF-8 catalyst, implying that deposition of NiO-PTA and corresponding calcination might affect not only the surface area, but also pore diameter. The macropores can also be seen in spent NiO-PTA/ZIF-8 catalyst, which were not blocked by deposited carbon.
Figure 4A present the FT-IR spectrum of ZIF-8 and NiO-PTA/ZIF-8 catalyst with an absorption region of 400–4000 cm−1. Several bands were observed for ZIF-8 in the FT-IR spectrum. For example, absorption bands at 2929 cm−1 and 3135 cm−1 were attributed to the aromatic and aliphatic C-H stretch of the imidazole, respectively74. The band at 1579 cm−1 could be assigned as the C = N stretch mode75. The absorption band at 420 cm−1 was observed for the Zn-N stretching mode, while those in the 1100–1400 cm−1 region were associated with the C-N stretch76. Compared to the pure ZIF-8, the FT-IR spectra of the NiO-PTA/ZIF-8 catalyst showed the absorption bands at 1043 cm−1, 951 cm−1, 842–875 cm−1 and 754 cm−1, respectively. This corresponds to the ν(P-Oa), terminal ν(W-Ot), corner-sharing ν(W-Ob) and edge-sharing ν(W-Oc) band vibrations of H3PW12O4077,78. The band at 403 cm−1 was assigned to the Ni-O stretching mode, which was difficult to observe. Bands below 600 cm−1 were due to the symmetric stretching vibration of metal-oxygen groups79, while ZIF-8 showed no apparent absorption in this region. These facts suggest that NiO and PTA were present in the catalysts. The presence of H2O in both samples was likely due to moisture adsorption when exposed to air.
Figure 4B showed XRD patterns of the ZIF-8, NiO-PTA/ZIF-8 and spent catalyst. Almost all of the XRD peaks for ZIF-8 were in good agreement with previous reports80, confirming the formation of pure crystalline ZIF-8 phase. A minimal amount of ZnO in the impurity phase was found at 31.7° 81. As expected, all three samples showed the characteristic reflection at 2θ = 7.3°, attributed to the 110 peak of ZIF-8 82. The powder XRD pattern showed no significant change in the crystalline structure of both NiO-PTA/ZIF-8 and spent catalyst, with respect to the plain ZIF-8. This indicates that the framework of ZIF-8 was stable throughout the entire process of catalyst preparation and catalytic reaction. However, the large amount of NiO and PTA dispersed at the molecular level in ZIF-8 led to a marked decrease in intensity at 7.3°, and the spent NiO-PTA/ZIF-8 catalyst showed more decrease at 7.3° due to carbon deposition. The XRD pattern of NiO-PTA/ZIF-8 catalyst did not show the characteristic diffraction peaks of NiO, suggesting that the NiO were highly dispersed on ZIF-8 83. An alternative explanation was that the signal was below the detection limit due to relatively low NiO loading50. In Fig. 3B the positions of the sharp peaks below 2θ = 10° (8.89°) could be ascribed to cubic phase H3PW12O40, and were indexed to the reported data (JCPDS 50-0304)84.
Figure 5 shows elemental surveys by X-ray photoelectron spectroscopy (XPS), which showed the presence of the ZIF-8 framework elements (Zn, C, N) and O in ZIF-8 sample and clearly confirmed the presence of not only Zn, C, N and O but also Ni and W in the NiO-PTA/ZIF-8 catalyst sample. The binding energy of 1021.82 eV corresponded to the Zn 2p3/2, while the other located at 1044.93 eV was attributed to the Zn 2p1/285. The binding energy distance between these two lines was 23.11 eV, indicating that the Zn ions in the composites were of +2 states51. After loading with NiO and PTA, the peak for Zn 2p shifted slightly to higher binding energy (from 1021.82 to 1022.02 and 1044.93 to 1045.16 eV, respectively), implying that the Zn were involved in NiO and PTA sorption86, and the weak binding or coordination of Zn in ZIF-8 to NiO and PTA87. As shown in Fig. 5, both samples exhibited a symmetric peak (about 399.06 eV) for the nitrogen on imidazole of the ZIF-8 nanoparticles88, indicating that there was only one form of nitrogen. The C 1 s peaks of two samples for the N-doped carbon materials were observed at about 284.85 eV, consistent with sp2 carbons89. In the O 1 s XPS spectrum, the bonding energy of ZIF-8 was peaked at 532.28 eV, which could be assigned to O2− ions90 in the Zn-O bonding of the wurtzite ZnO structure, which has been also observed in XRD results. After adding NiO and PTA, the bonding energy was decreased from 532.28 to 531.17 eV. Such a negative shift could be due to the rich electron density on the oxygen atoms arising from the Zn-O linkage in the catalyst. In Fig. 5, two peaks for the 2p3/2 and 2p1/2 components at 855.62 eV and 873.70 eV were characteristics of the NiO phase and were in accordance with the literature91. Furthermore, the presence of two shakeup satellite peaks (861.14 eV and 880.44 eV for satellite of Ni 2p3/2 and Ni 2p1/2, respectively) indicated the electronic state of the Ni2+ ion92. This observation confirmed that the NiO-PTA/ZIF-8 catalyst contained more oxo-Ni species due to the larger peak areas. Notably, the peak at 852.73 eV was ascribed to metallic Ni93. This could be due to the reduction of nickel ions, while the positive shifts in binding energies of the Zn 2p states were ascribed to the oxidation of zinc ions. This implies that Zn species might donate partial electrons to Ni oxide species, the electron transfer between Zn and Ni due to the NiO-loaded and calcination. As shown in Fig. 5, the W 4f spectrum contained a doublet at a binding energy of 35.38 and 37.52 eV, assigned to W 4f7/2 and W 4f5/2 lines, respectively, which were characteristic of the W6+ ion94. This result clearly showed the existence of assembled NiO and PTA on NiO-PTA/ZIF-8 catalyst. Furthermore, the surface atomic contents of the NiO-PTA/ZIF-8 catalyst were 0.84% for Ni and 2.53% for W. This indicates that the catalyst was comprised of more tungsten atoms and was deficient in nickel atoms on the surface, which is in line with the EDS measurement.
Catalytic properties of NiO-PTA/ZIF-8 catalyst in hydrocracking of Jatropha oil
Figure 6A displays GC chromatograms of product oil from NiO-PTA/Al2O3 catalyst and NiO-PTA/ZIF-8 catalyst. Results show that the major components in both product oils were C15H32, C16H34, C17H36, and C18H38. Heptadecane and octadecane were the two most abundant liquid alkanes, which were produced from the fatty acids of the triglycerides. Although the product of C17H36 and C18H38 over NiO-PTA/Al2O3 catalyst produced more Iso-alkanes, this catalyst also had more light fraction (<C15) than that over NiO-PTA/ZIF-8 catalyst. These reactions are undesirable in the hydroconversion of triglycerides, because the by-products formed block the reaction sites and also act as sites for coke formation on the surface of the catalyst3. They both showed heavy fraction (>C18), which mainly contained long chain esters formed by esterification of alcohol and free fatty acid95, or stable oxygenated intermediate products such as esters and some acids, alcohols, aldehydes and ethers96.
Figure 6B displays the selectivity of product oil and conversion of Jatropha oil over the two catalysts. Although the Jatropha oil conversions over NiO-PTA/Al2O3 catalyst was close to the NiO-PTA/ZIF-8 catalyst (both more than 90%), the C15-C18 hydrocarbon selectivity over the NiO-PTA/ZIF-8 catalyst (67.31%) was much more than that of the NiO-PTA/Al2O3 catalyst (30.78%), and the selectivity increased 36.53% by NiO-PTA/ZIF-8 catalyst. We speculated that hydrocarbons less than C15 were probably adsorbed and detained in the micropore, and could not diffuse from the catalyst. This resulted in an increase of C15-C18 hydrocarbon selectivity. Moreover, appropriate amounts of macropores would favor the impregnation of large-size PTA molecules and readily allow the diffusion of bulky triglyceride molecules and prevent pore blockage.
The stability of the NiO-PTA/ZIF-8 catalyst was investigated in a continuous flow reactor at 360 °C, 3 MPa, LHSV 9 h−1 (Table 2). The selectivity of products and conversion of Jatropha oil measured at 15, 44, 76 and 104 h on stream, and the catalyst was stable over the entire duration. Results show that Jatropha oil conversion declined by 17%; however, this was still more than 75% during the 104 h. The liquid hydrocarbon (C15-C18) selectivity remained constant. This indicates that there was no significant deactivation of the catalyst with reaction time.
Reaction kinetics
A Langmuir-Hinshelwood model was used in the first kinetic study on the hydrocracking of Jatropha oil over different catalysts below 360 °C, 3.0 MPa and 9–36 h−1. The following first-order equation was obtained97:
![](http://media.springernature.com/lw184/springer-static/image/art%3A10.1038%2Fsrep23667/MediaObjects/41598_2016_Article_BFsrep23667_Equ3_HTML.gif)
where X is the conversion of triglyceride to the hydrocarbon products, kH (h−1) is the hydrocracking rate constant, W (g) is the weight of the catalyst and F (L/h) is the flow rate of triglyceride. The essentially linear relationship of −ln(1 − X) vs. reciprocal space velocity and the apparent first-order plot for the hydrocracking of Jatropha oil is shown in Fig. 7. This indicates that the experimental data followed empiric pseudo-first-order-kinetics.
The activity of catalysts in hydrocracking can be described by examining the conversion of triglycerides. This involves evaluating the rate of disappearance of triglycerides, using pseudo-first order kinetics to fit the relevant experimental data for different catalysts at 360 °C and 3.0 MPa98. Results are presented in Table 3. The relative pseudo-first order rate constants (kH) of NiO-PTA/Al2O3 and NiO-PTA/ZIF-8 catalyst were calculated, and results show that the kH of NiO-PTA/ZIF-8 catalyst was 1.4-fold higher than that of the NiO-PTA/Al2O3 catalyst under the same reaction condition. This indicates that the conversion of triglyceride over the NiO-PTA/ZIF-8 catalyst was higher than that of the NiO-PTA/Al2O3 catalyst. The values of activation energy (EH) calculated from the Arrhenius equation []99 were summarized in Table 3. Thermodynamic parameters for two catalysts were evaluated for the temperature range of 280–400 °C, while the pressure and LHSV were maintained at 3.0 MPa and 9 h−1. EH suggests the relative difficulty of the conversion of triglycerides. As shown in Table 3, the activation energy of conversion of triglycerides over NiO-PTA/ZIF-8 was lower than NiO-PTA/Al2O3. This indicates that conversion of triglyceride was easier over NiO-PTA/ZIF-8, due to its higher hydrocracking activity. This may be related to the metal active center (Ni and W phase). The NiO-PTA/ZIF-8 catalyst showed a high surface area, high metal content and uniform metal dispersion (proven by BET, XPS and SEM-EDS results), leading to the formation of a more active center and then a marked increase in hydrogenation activity.
Table S1 in Supplementary Information showed the effect of LHSV on the conversions of Jatropha oil and selectivity of products oil over NiO-PTA/ZIF-8 catalyst at reaction temperature 280–400 °C. It can be seen that the conversion and selectivity of C15-C18 both decreases as the LHSV increases from 4.5 to 36 h−1 under temperature of 280–360 °C. This decrease is due to the fact that with increasing LHSV, the contact time of the oil on the catalyst decreases, resulting in lower conversion as well as selectivity of main product. However, selectivity of C15-C18 increases when the LHSV increasing, it probably because that cracking ability of alkane increases at 400 °C, it can be observed that the light fractions (<C15) are more than that at 280–360 °C. While, the cracking ability decreases as the LHSV increasing which leads to the selectivity of C15-C18 increase, but the conversions of Jatropha oil are also decreased.
Discussion
In this study, 10 g NiO-PTA/Al2O3 catalyst was required to reach the same conversion of Jatropha oil as the NiO-PTA/ZIF-8 catalyst (1.0 g). Compared with the NiO-PTA/Al2O3 catalyst, the dosage of catalyst decreased 10 times and catalytic efficiency increased 10 times over the NiO-PTA/ZIF-8 catalyst. As shown in Fig. S3 (see supplementary information), the NiO-PTA/Al2O3 also exhibited Langmuir type IV isotherms with a typical mesoporous material and size-homogeneous 1D slit channels100,101. The total pore volume and micropore volume of NiO-PTA/Al2O3 were 0.39 cm3/g and 0.08 cm3/g, which were both smaller than NiO-PTA/ZIF-8 catalyst (0.54 cm3/g and 0.21 cm3/g). The BET surface area of NiO-PTA/Al2O3 was only 223 m2/g, while that of the NiO-PTA/ZIF-8 catalyst was more than 600 m2/g. Generally, the catalysts at a nanosize scale with a high surface area should provide the catalysts with higher activity102. Thus, the NiO-PTA/ZIF-8 catalyst possessed more active sites for hydrocracking of Jatropha oil than the NiO-PTA/Al2O3 catalyst. As confirmed by XPS results, the surface atomic contents of the NiO-PTA/ZIF-8 catalyst were 0.84% for Ni and 2.53% for W, and 0.41% for Ni and 1.29% for W of NiO-PTA/Al2O3 catalyst. We also prepared another sample of NiO-PTA/ZIF-8 catalyst with similar atomic content (0.53% for Ni and 1.36% for W) to NiO-PTA/Al2O3 catalyst, as shown in Fig. S3. The BET surface area, total pore volume and micropore volume of the NiO-PTA/ZIF-8 catalyst were 814 m2/g, 0.47 cm3/g and 0.28 cm3/g, respectively. These figures were still larger than that of the NiO-PTA/Al2O3 catalyst. GC results are showed in Fig. S4 (see supplementary information). The Jatropha oil conversions over the NiO-PTA/ZIF-8 catalyst was 92.55%, which was close to that of the NiO-PTA/Al2O3 catalyst. However, the C15-C18 hydrocarbon selectivity of the NiO-PTA/ZIF-8 catalyst (53.76%) was also more than that of the NiO-PTA/Al2O3 catalyst (30.78%). Therefore, pore structure as well as the surface area played an important role in the activity of the catalyst.
In conclusion, a highly efficient NiO-PTA/ZIF-8 catalyst was successfully prepared through the impregnation method. Results show the prominently enhanced selectivity of C15-C18 hydrocarbon (67.31%) for hydrocracking of Jatropha oil compare to the NiO-PTA/Al2O3 catalyst. Product selectivity increased 36.53% due to ZIF micropore structure, and the catalytic efficiency increased 10 times with the NiO-PTA/ZIF-8 catalyst due to its high catalyst surface area. The NiO-PTA/ZIF-8 catalyst exhibited excellent performance and stability in the reaction. The kinetic behavior of two catalysts was examined with an assumption of pseudo-first-order reaction kinetics. This work sheds light on new opportunities in the development of other metal particles (e.g., Pt and W), which have wide potential applications in catalytic reactions. Since non-sulfided NiO-PTA/ZIF-8 catalyst can bypass the presulfurization process, shows promise as an alternative to sulfided catalysts for green diesel production.
Additional Information
How to cite this article: Liu, J. et al. NiO-PTA supported on ZIF-8 as a highly effective catalyst for hydrocracking of Jatropha oil. Sci. Rep. 6, 23667; doi: 10.1038/srep23667 (2016).
References
Verma, D., Rana, B. S., Kumar, R., Sibi, M. G. & Sinha, A. K. Diesel and aviation kerosene with desired aromatics from hydroprocessing of jatropha oil over hydrogenation catalysts supported on hierarchical mesoporous SAPO-11. Appl. Catal. A-Gen. 490, 108–116 (2015).
Al Alwan, B., Salley, S. O. & Ng, K. Y. S. Hydrocracking of DDGS corn oil over transition metal carbides supported on Al-SBA-15: Effect of fractional sum of metal electronegativities. Appl. Catal. A-Gen. 485, 58–66 (2014).
Anand, M., Sibi, M. G., Verma, D. & Sinha, A. K. Anomalous hydrocracking of triglycerides over CoMo-catalyst–influence of reaction intermediates. J. Chem. Sci. 126, 473–480 (2014).
Gong, S., Shinozaki, A. & Qian, E. W. Role of Support in Hydrotreatment of Jatropha Oil over Sulfided NiMo Catalysts. Ind. Eng. Chem. Res. 51, 13953–13960 (2012).
Liu, J., Fan, K., Tian, W., Liu, C. & Rong, L. Hydroprocessing of Jatropha oil over NiMoCe/Al2O3 catalyst. Int. J. Hydrogen Energy 37, 17731–17737 (2012).
Wang, H., Yan, S., Salley, S. O. & Simon Ng, K. Y. Support effects on hydrotreating of soybean oil over NiMo carbide catalyst. Fuel 111, 81–87 (2013).
Kimura, T. et al. Hydroconversion of Triglycerides to Hydrocarbons Over Mo–Ni/γ-Al2O3 Catalyst Under Low Hydrogen Pressure. Catal. Lett. 143, 1175–1181 (2013).
Krár, M., Kovács, S., Kalló, D. & Hancsók, J. Fuel purpose hydrotreating of sunflower oil on CoMo/Al2O3 catalyst. Bioresour. Technol. 101, 9287–9293 (2010).
Anand, M. & Sinha, A. K. Temperature-dependent reaction pathways for the anomalous hydrocracking of triglycerides in the presence of sulfided Co–Mo-catalyst. Bioresour. Technol. 126, 148–155 (2012).
García-Dávila, J. et al. Jatropha curcas L. oil hydroconversion over hydrodesulfurization catalysts for biofuel production. Fuel 135, 380–386 (2014).
Barrón, C. A. E. et al. Catalytic hydrocracking of vegetable oil for agrofuels production using Ni–Mo, Ni–W, Pt and TFA catalysts supported on SBA-15. Catal. Today 166, 102–110 (2011).
Seo, M.-g., Lee, D.-W., Lee, K.-Y. & Moon, D. J. Pt/Al-SBA-15 catalysts for hydrocracking of C21–C34 n-paraffin mixture into gasoline and diesel fractions. Fuel 143, 63–71 (2015).
Veriansyah, B. et al. Production of renewable diesel by hydroprocessing of soybean oil: Effect of catalysts. Fuel 94, 578–585 (2012).
Gong, S., Shinozaki, A., Shi, M. & Qian, E. W. Hydrotreating of Jatropha Oil over Alumina Based Catalysts. Energy Fuels 26, 2394–2399 (2012).
Liu, Y., Sotelo-Boyás, R., Murata, K., Minowa, T. & Sakanishi, K. Hydrotreatment of Jatropha oil to produce green diesel over trifunctional Ni-Mo/SiO2-Al2O3 catalyst. Catal. Lett. 38, 552–553 (2009).
Liu, Y., Sotelo-Boyás, R., Murata, K., Minowa, T. & Sakanishi, K. Hydrotreatment of Vegetable Oils to Produce Bio-Hydrogenated Diesel and Liquefied Petroleum Gas Fuel over Catalysts Containing Sulfided Ni–Mo and Solid Acids. Energy Fuels 25, 4675–4685 (2011).
Sotelo-Boyás, R., Liu, Y. & Minowa, T. Renewable Diesel Production from the Hydrotreating of Rapeseed Oil with Pt/Zeolite and NiMo/Al2O3 Catalysts. Ind. Eng. Chem. Res. 50, 2791–2799 (2011).
Sankaranarayanan, T. M., Banu, M., Pandurangan, A. & Sivasanker, S. Hydroprocessing of sunflower oil–gas oil blends over sulfided Ni–Mo–Al–zeolite beta composites. Bioresour. Technol. 102, 10717–10723 (2011).
Ishihara, A., Fukui, N., Nasu, H. & Hashimoto, T. Hydrocracking of soybean oil using zeolite–alumina composite supported NiMo catalysts. Fuel 134, 611–617 (2014).
Doherty, C. M. et al. Using Functional Nano- and Microparticles for the Preparation of Metal-Organic Framework Composites with Novel Properties. Acc. Chem. Res. 47, 396–405 (2014).
Ou, S. & Wu, C. D. Rational construction of metal-organic frameworks for heterogeneous catalysis. Inorg. Chem. Front. 1, 721–734 (2014).
Li, S. Z. & Huo, F. W. Metal-organic framework composites: from fundamentals to applications. Nanoscale 7, 7482–7501 (2015).
Zhu, Q. L. & Xu, Q. Metal-organic framework composites. Chem. Soc. Rev. 43, 5468–5512 (2014).
Aijaz, A. & Xu, Q. Catalysis with Metal Nanoparticles Immobilized within the Pores of Metal–Organic Frameworks. J. Phys. Chem. Lett. 5, 1400–1411 (2014).
Liu, J. W. et al. Applications of metal-organic frameworks in heterogeneous supramolecular catalysis. Chem. Soc. Rev. 43, 6011–6061 (2014).
Gu, Z. Y., Park, J., Raiff, A., Wei, Z. W. & Zhou, H. C. Metal-Organic Frameworks as Biomimetic Catalysts. Chemcatchem 6, 67–75 (2014).
Falkowski, J. M., Liu, S. & Lin, W. B. Metal-Organic Frameworks as Single-Site Solid Catalysts for Asymmetric Reactions. Isr. J. Chem. 52, 591–603 (2012).
He, M. et al. Facile synthesis of zeolitic imidazolate framework-8 from a concentrated aqueous solution. Microporous Mesoporous Mater. 184, 55–60 (2014).
Thompson, J. A. et al. Tunable CO2 Adsorbents by Mixed-Linker Synthesis and Postsynthetic Modification of Zeolitic Imidazolate Frameworks. J. Phys. Chem. C 117, 8198–8207 (2013).
Almasoudi, A. & Mokaya, R. Preparation and hydrogen storage capacity of templated and activated carbons nanocast from commercially available zeolitic imidazolate framework. J. Mater. Chem. 22, 146–152 (2012).
Fischer, M. & Bell, R. G. Interaction of hydrogen and carbon dioxide with sod-type zeolitic imidazolate frameworks: a periodic DFT-D study. CrystEngComm 16, 1934–1949 (2014).
Amirilargani, M. & Sadatnia, B. Poly(vinyl alcohol)/zeolitic imidazolate frameworks (ZIF-8) mixed matrix membranes for pervaporation dehydration of isopropanol. J. Membr. Sci. 469, 1–10 (2014).
Liu, X. et al. Improvement of hydrothermal stability of zeolitic imidazolate frameworks. Catal. Commun. 49, 9140–9142 (2013).
Pan, Y. & Lai, Z. Sharp separation of C2/C3 hydrocarbon mixtures by zeolitic imidazolate framework-8 (ZIF-8) membranes synthesized in aqueous solutions. Catal. Commun. 47, 10275–10277 (2011).
Lu, G. et al. Imparting functionality to a metal–organic framework material by controlled nanoparticle encapsulation. Nat. Chem. 4, 310–316 (2012).
Zhou, X. et al. Zeolitic imidazolate framework as efficient heterogeneous catalyst for the synthesis of ethyl methyl carbonate. J. Mol. Catal. A: Chem. 366, 43–47 (2013).
Chizallet, C. et al. Catalysis of Transesterification by a Nonfunctionalized Metal−Organic Framework: Acido-Basicity at the External Surface of ZIF-8 Probed by FTIR and ab Initio Calculations. J. Am. Chem. Soc. 132, 12365–12377 (2010).
Nguyen, L. T. L., Le, K. K. A. & Phan, N. T. S. A Zeolite Imidazolate Framework ZIF-8 Catalyst for Friedel-Crafts Acylation. Chin. J. Catal. 33, 688–696 (2012).
Dai, H. et al. Synergistic catalysis of AgPd@ZIF-8 on dehydrogenation of formic acid. Appl. Catal. B-Environ. 165, 57–62 (2015).
Zhao, Y. et al. Pd nanoparticles supported on ZIF-8 as an efficient heterogeneous catalyst for the selective hydrogenation of cinnamaldehyde. Catal. Commun. 57, 119–123 (2014).
Wang, C. et al. Multifunctional Pd@MOF core–shell nanocomposite as highly active catalyst for p-nitrophenol reduction. Catal. Commun. 72, 29–32 (2015).
Yin, H., Kim, H., Choi, J. & Yip, A. C. K. Thermal stability of ZIF-8 under oxidative and inert environments: A practical perspective on using ZIF-8 as a catalyst support. Chem. Eng. J. 278, 293–300 (2015).
Schejn, A. et al. Fe3O4@ZIF-8: magnetically recoverable catalysts by loading Fe3O4 nanoparticles inside a zinc imidazolate framework. Dalton Trans. 44, 10136–10140 (2015).
Xia, B., Chen, K., Luo, W. & Cheng, G. NiRh nanoparticles supported on nitrogen-doped porous carbon as highly efficient catalysts for dehydrogenation of hydrazine in alkaline solution. Nano Res. 8, 3472–3479 (2015).
Li, J., Zhu, Q.-L. & Xu, Q. Pd nanoparticles supported on hierarchically porous carbons derived from assembled nanoparticles of a zeolitic imidazolate framework (ZIF-8) for methanol electrooxidation. Catal. Commun. 51, 10827–10830 (2015).
Dang, T. T. et al. Palladium Nanoparticles Supported on ZIF-8 As an Efficient Heterogeneous Catalyst for Aminocarbonylation. ACS Catal. 3, 1406–1410 (2013).
Zhang, M. et al. PVP-Pd@ZIF-8 as highly efficient and stable catalysts for selective hydrogenation of 1, 4-butynediol. Catal. Sci. Technol. 4, 329–332 (2014).
Bhattacharjee, S., Jang, M. S., Kwon, H. J. & Ahn, W. S. Zeolitic Imidazolate Frameworks: Synthesis, Functionalization, and Catalytic/Adsorption Applications. Catal. Surv. Asia 18, 101–127 (2014).
Jiang, H. L., Akita, T., Ishida, T., Haruta, M. & Xu, Q. Synergistic Catalysis of Au@Ag Core–Shell Nanoparticles Stabilized on Metal–Organic Framework. J. Am. Chem. Soc. 133, 1304–1306 (2011).
Hou, C. et al. Hydroformylation of alkenes over rhodium supported on the metal-organic framework ZIF-8. Nano Res. 7, 1364–1369 (2014).
Li, P. Z., Aranishi, K. & Xu, Q. ZIF-8 immobilized nickel nanoparticles: highly effective catalysts for hydrogen generation from hydrolysis of ammonia borane. Chem. Commun. 48, 3173–3175 (2012).
Helm, M. L., Stewart, M. P., Bullock, R. M., DuBois, M. R. & DuBois, D. L. A Synthetic Nickel Electrocatalyst with a Turnover Frequency Above 100,000 s−1 for H2 Production. Science 333, 863–866 (2011).
Deng, Q. et al. Highly selective self-condensation of cyclic ketones using MOF-encapsulating phosphotungstic acid for renewable high-density fuel. Green Chem. 17, 4473–4481 (2015).
Zhang, F. et al. Polyoxometalates confined in the mesoporous cages of metal–organic framework MIL-100(Fe): Efficient heterogeneous catalysts for esterification and acetalization reactions. Chem. Eng. J. 269, 236–244 (2015).
Wee, L. H. et al. Copper Benzene Tricarboxylate Metal–Organic Framework with Wide Permanent Mesopores Stabilized by Keggin Polyoxometallate Ions. J. Am. Chem. Soc. 134, 10911–10919 (2012).
Micek-Ilnicka, A. & Gil, B. Heteropolyacid encapsulation into the MOF: influence of acid particles distribution on ethanol conversion in hybrid nanomaterials. Dalton Trans. 41, 12624–12629 (2012).
Liu, J. et al. Hydroprocessing of Jatropha Oil for Production of Green Diesel over Non-sulfided Ni-PTA/Al2O3 Catalyst. Sci. Rep. 5, 11327 (2015).
Fan, K., Liu, J., Yang, X. & Rong, L. Effect of Keggin-type heteropolyacids on the hydrocracking of Jatropha oil. RSC Adv. 5, 37916–37924 (2015).
Liu, J. et al. A Non-sulfided flower-like Ni-PTA Catalyst that Enhances the Hydrotreatment Efficiency of Plant Oil to Produce Green Diesel. Sci. Rep. 5, 15576 (2015).
Rizo-Acosta, P., Linares-Vallejo, M. T. & Muñoz-Arroyo, J. A. Co-hydroprocessing of a mixture: Vegetable oil/n-hexadecane/4,6-dimethyldibenzothiophene for the production of sustainable hydrocarbons. A kinetic modeling. Catal. Today 234, 192–199 (2014).
Achten, W. M. J. et al. Jatropha bio-diesel production and use. Biomass Bioenergy 32, 1063–1084 (2008).
Rösler, C. et al. Encapsulation of Bimetallic Nanoparticles into a Metal–Organic Framework: Preparation and Microstructure Characterization of Pd/Au@ZIF-8. Eur. J. Inorg. Chem. 2014, 5514–5521 (2014).
Fan, K., Liu, J., Yang, X. & Rong, L. Hydrocracking of Jatropha oil over Ni-H3PW12O40/nano-hydroxyapatite catalyst. Int. J. Hydrogen Energy 39, 3690–3697 (2014).
Liu, J., Liu, C., Zhou, G., Shen, S. & Rong, L. Hydrotreatment of Jatropha oil over NiMoLa/Al2O3 catalyst. Green Chem. 14, 2499–2505 (2012).
Sinha, A. K. et al. Process Intensification for Hydroprocessing of Vegetable Oils: Experimental Study. Ind. Eng. Chem. Res. 53, 19062–19070 (2014).
Priecel, P., Kubička, D., Čapek, L., Bastl, Z. & Ryšánek, P. The role of Ni species in the deoxygenation of rapeseed oil over NiMo-alumina catalysts. Appl. Catal. A-Gen. 397, 127–137 (2011).
Tiwari, R. et al. Hydrotreating and hydrocracking catalysts for processing of waste soya-oil and refinery-oil mixtures. Catal. Commun. 12, 559–562 (2011).
Mikulec, J., Cvengroš, J., Joríková, Ľ., Banič, M. & Kleinová, A. Second generation diesel fuel from renewable sources. J. Cleaner Prod. 18, 917–926 (2010).
Šimáček, P., Kubička, D., Šebor, G. & Pospíšil, M. Fuel properties of hydroprocessed rapeseed oil. Fuel 89, 611–615 (2010).
Zhong, H.-x. et al. ZIF-8 Derived Graphene-Based Nitrogen-Doped Porous Carbon Sheets as Highly Efficient and Durable Oxygen Reduction Electrocatalysts. Angew. Chem. Int. Ed. 53, 14235–14239 (2014).
Wang, S., Fan, Y. & Jia, X. Sodium dodecyl sulfate-assisted synthesis of hierarchically porous ZIF-8 particles for removing mercaptan from gasoline. Chem. Eng. J. 256, 14–22 (2014).
Zhang, T. et al. Pd nanoparticles immobilized in a microporous/mesoporous composite ZIF-8/MSS: A multifunctional catalyst for the hydrogenation of alkenes. Microporous and Mesoporous Mater. 197, 324–330 (2014).
Yurderi, M., Bulut, A., Zahmakiran, M., Gülcan, M. & Özkar, S. Ruthenium(0) nanoparticles stabilized by metal-organic framework (ZIF-8): Highly efficient catalyst for the dehydrogenation of dimethylamine-borane and transfer hydrogenation of unsaturated hydrocarbons using dimethylamine-borane as hydrogen source. Appl. Catal. B-Environ. 160–161, 534–541 (2014).
Zhang, T. et al. Core–shell Pd/ZSM-5@ZIF-8 membrane micro-reactors with size selectivity properties for alkene hydrogenation. Catal. Today 236, Part A, 41–48 (2014).
He, M. et al. Facile synthesis of zeolitic imidazolate framework-8 from a concentrated aqueous solution. Microporous and Mesoporous Mater. 184, 55–60 (2014).
Ren, H. et al. Polyacrylic acid@zeolitic imidazolate framework-8 nanoparticles with ultrahigh drug loading capability for pH-sensitive drug release. Chem. Commun. 50, 1000–1002 (2014).
Liu, J. W., Liu, Y. C., He, H., Yang, B. F. & Yang, G. Y. Novel organic–inorganic hybrid monomeric Keggin-type phosphotungstate containing heterometallic Ni6WNi clusters. Inorg. Chem. Commun. 53, 60–63 (2015).
Li, R. et al. Polyoxometallates trapped in a zeolitic imidazolate framework leading to high uptake and selectivity of bioactive molecules. J. Mater. Chem. A 2, 2168–2173 (2014).
Shim, J., Venkata Reddy, C., Sarma, G. V. S. S., Narayana Murthy, P. & Ravikumar, R. V. S. S. N. Effect of Co(2+) and Ni(2+)-doped zinc borate nano crystalline powders by co-precipitation method. Spectrochim. acta. Part A 142, 279–285 (2015).
Singh, A. K. & Xu, Q. Metal–Organic Framework Supported Bimetallic Ni·Pt Nanoparticles as High-performance Catalysts for Hydrogen Generation from Hydrazine in Aqueous Solution. ChemCatChem 5, 3000–3004 (2013).
Marti, A., Van, M. & Balkus, K., Jr. Tuning the crystal size and morphology of the substituted imidazole material, SIM-1. J. Porous Mater. 21, 889–902 (2014).
Liédana, N., Galve, A., Rubio, C., Téllez, C. & Coronas, J. CAF@ZIF-8: One-Step Encapsulation of Caffeine in MOF. ACS Appl. Mater. Interfaces 4, 5016–5021 (2012).
Liu, M., Fan, B., Shi, X. & Li, R. Ru/ZIF-8 with a chiral modifier for asymmetric hydrogenation of acetophenone. Catal. Commun. 42, 20–24 (2013).
Chen, L. & Bai, B. Facile Preparation of Phosphotungstic Acid-Impregnated Yeast Hybrid Microspheres and Their Photocatalytic Performance for Decolorization of Azo Dye. Int. J. Photoenergy 2013, 9 (2013).
Li, C. et al. Decoration of graphene network with metal–organic frameworks for enhanced electrochemical capacitive behavior. Carbon 78, 231–242 (2014).
Jian, M., Liu, B., Zhang, G., Liu, R. & Zhang, X. Adsorptive removal of arsenic from aqueous solution by zeolitic imidazolate framework-8 (ZIF-8) nanoparticles. Colloids Surf. A 465, 67–76 (2015).
Jiang, J. Q., Yang, C. X. & Yan, X. P. Zeolitic Imidazolate Framework-8 for Fast Adsorption and Removal of Benzotriazoles from Aqueous Solution. ACS Appl. Mater. Interfaces 5, 9837–9842 (2013).
Liu, C. et al. MOFs synthesized by the ionothermal method addressing the leaching problem of IL-polymer composite membranes. Chem. Commun. 50, 14121–14124 (2014).
Bai, F., Xia, Y., Chen, B., Su, H. & Zhu, Y. Preparation and carbon dioxide uptake capacity of N-doped porous carbon materials derived from direct carbonization of zeolitic imidazolate framework. Carbon 79, 213–226 (2014).
He, L. et al. Fabrication of Au/ZnO nanoparticles derived from ZIF-8 with visible light photocatalytic hydrogen production and degradation dye activities. Dalton Trans. 43, 16981–16985 (2014).
Anandha Babu, G., Ravi, G., Navaneethan, M., Arivanandhan, M. & Hayakawa, Y. An investigation of flower shaped NiO nanostructures by microwave and hydrothermal route. J. Mater. Sci. Mater. Electron. 25, 5231–5240 (2014).
Dalavi, D. S. et al. Electrochromic properties of dandelion flower like nickel oxide thin films. J. Mater. Chem. A 1, 1035–1039 (2013).
Jian, M., Liu, B., Zhang, G., Liu, R. & Zhang, X. Adsorptive removal of arsenic from aqueous solution by zeolitic imidazolate framework-8 (ZIF-8) nanoparticles. Colloids Surf. 465, 67–76 (2015).
Chakhari, S., Younes, M., Rives, A. & Ghorbel, A. Textural, structural and catalytic properties of zirconia doped by heteropolytungstic acid: a comparative study between aerogel and xerogel catalysts. J. Sol-Gel Sci. Technol. 69, 378–385 (2014).
Toba, M. et al. Hydrodeoxygenation of waste vegetable oil over sulfide catalysts. Catal. Today 164, 533–537 (2011).
Anand, M. & Sinha, A. K. Temperature-dependent reaction pathways for the anomalous hydrocracking of triglycerides in the presence of sulfided Co–Mo-catalyst. Bioresour. Technol. 126, 148–155 (2012).
Furimsky, E. Catalytic hydrodeoxygenation. Appl. Catal. A-Gen. 199, 147–190 (2000).
Kumar, R. et al. Hydroprocessing of jatropha oil and its mixtures with gas oil. Green Chem. 12, 2232–2239 (2010).
Ferdous, D., Dalai, A. & Adjaye, J. Hydrodenitrogenation and hydrodesulfurization of heavy gas oil using NiMo/Al2O3 catalyst containing boron: Experimental and kinetic studies. Ind. Eng. Chem. Res. 45, 544–552 (2006).
Wang, S., Li, X., Yin, Q., Zhu, L. & Luo, Z. Highly active and selective Cu/SiO2 catalysts prepared by the urea hydrolysis method in dimethyl oxalate hydrogenation. Catal. Commun. 12, 1246–1250 (2011).
Yin, A., Guo, X., Dai, W.-L. & Fan, K. Effect of initial precipitation temperature on the structural evolution and catalytic behavior of Cu/SiO2 catalyst in the hydrogenation of dimethyloxalate. Catal. Commun. 12, 412–416 (2011).
Zhao, B. et al. Synthesis of Flower-Like NiO and Effects of Morphology on Its Catalytic Properties. J. Phys. Chem. C 113, 14440–14447 (2009).
Acknowledgements
This work was supported by the “Special Fund for Beijing Common Construction Project” and “Beijing Natural Science Foundation of China (2142024)”.
Author information
Authors and Affiliations
Contributions
J.D.L. initiated the project and conceived. J.L. supervised the experiments and wrote the paper. J.H. and L.Y.W. prepared and characterized the samples. R.L., P.C. and X.R. analyzed the data. L.H.D. and L.R. provided assistance with the analysis of the data and the revision of the paper, respectively. All authors reviewed the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Liu, J., He, J., Wang, L. et al. NiO-PTA supported on ZIF-8 as a highly effective catalyst for hydrocracking of Jatropha oil. Sci Rep 6, 23667 (2016). https://doi.org/10.1038/srep23667
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep23667
- Springer Nature Limited
This article is cited by
-
pH-Sensitive Stimulus Responsive ZIF-8 Composites Nanoparticles Coated with Folic Acid-Conjugated Chitosan for Targeted Delivery of Curcumin
Journal of Cluster Science (2024)
-
N-doped carbon nanocube with zinc oxide sodiophilic sites enables a superior sodium metal anode
Nano Research (2023)
-
Synergistic Effect of 2D ZIF Loading and Ionic Liquid Modification on Improving Gas Separation Performance of PES-Based Mixed Matrix Hollow Fiber Membrane
Arabian Journal for Science and Engineering (2023)
-
Poly(lactic acid) Nanofibrous Scaffolds Containing Aspirin-loaded Zeolitic Imidazolate Frameworks: Morphology, Drug Release, Hemocompatibility and Shape Memory Studies
Fibers and Polymers (2022)
-
Co-precipitation synthesis of reusable ZnAl-CLDH/ZIF-8 heterojunction for enhanced photodegradation of organic dye
Journal of Materials Science: Materials in Electronics (2021)