Abstract
Topological mechanical metamaterials have been widely explored for their boundary states, which can be robustly isolated or transported in a controlled manner. However, such systems often require pre-configured design or complex active actuation for wave manipulation. Here, we present the possibility of in-situ transfer of topological boundary modes by leveraging the reconfigurability intrinsic in twisted origami lattices. In particular, we employ a dimer Kresling origami system consisting of unit cells with opposite chirality, which couples longitudinal and rotational degrees of freedom in elastic waves. The quasi-static twist imposed on the lattice alters the strain landscape of the lattice, thus significantly affecting the wave dispersion relations and the topology of the underlying bands. This in turn facilitates an efficient topological state transfer from one edge to the other. This simple and practical approach to energy transfer in origami-inspired lattices can thus inspire a new class of efficient energy manipulation devices.
Similar content being viewed by others
Introduction
In recent decades, mechanical metamaterials have been considered an ideal medium to design effective wave manipulation systems, leveraging their high degree of freedom in design and the tailorability of their mechanical properties1,2,3. Mechanical metamaterials are primarily highlighted for their unconventional dynamic responses that can offer rich applications, including vibration isolation4,5,6,7,8,9, wave guiding10,11,12,13, and energy harvesting6,14,15. More recently, the discovery of the topological insulators has significantly influenced and extended the design of wave-guiding mechanical metamaterials16,17. Topological insulators are known for their robustness of the boundary states18, which can lead to interesting wave properties for classical systems19,20. In addition, inspired by the concept of Thouless adiabatic quantized pumping21, which is based on an adiabatic cyclic modulation of the one-dimensional (1D) potential parameters, diverse lattice models have demonstrated the efficient transfer of the energy between the states, by employing the spatially22,23,24,25,26 or temporally27,28,29,30,31 varying configurations.
In parallel, recent studies have explored protocols for exploiting the topological properties of several systems, quantum32,33,34,35,36 and classical37, for the state transfer of localized states, a process of great importance for quantum technologies. The key advantage topology offers in such a process is the inherent protection of the topologically protected boundary against disorder. This is a significant improvement over the conventional systems, which usually involve energy leakage due to the noises and fabrication errors in the system. However, even in topological systems, most systems suffer from inefficiency in energy management. They either use pre-configured passive lattices that are not tunable after assembly22,23,24,25,26 or use a complex setting of active elements spanning the entire structure29,31, which is cumbersome for practical purposes.
To address such limitations, we employ a mechanical lattice consisting of origami-based mechanical units, which offers a simple strategy to tune wave dispersion relationships in-situ and facilitate a robust state transfer. Origami has served as an efficient design principle to tailor kinematic and static responses in mechanical metamaterials. Lately, the origami-inspired metamaterials have also been found to be effective in realizing the wave manipulation in them, leveraging their high reconfigurability and controllability38,39. Furthermore, origami lattices have also been shown to support static (zero-frequency) topological edge states40, suggesting the potential of origami lattices for topological mechanical metamaterials.
In this study, we consider the 1D dimer lattice composed of the origami unit cells to explore the tunable wave dispersion relationship and the emerging topological edge states at finite frequency. The origami unit is based on the Kresling pattern with opposite chirality, which shows the axial–rotation coupling and nonlinear static responses41,42. Interestingly, due to this axial–rotation coupling in our system, alternating chirality along the length of the lattice itself leads to the opening of a lower band gap. We find that this lower band gap is topologically nontrivial, and we demonstrate experimentally that this lower band gap hosts topologically protected edge states.
A more interesting mechanism is obtained when the lattice is twisted, which incurs the change of the axial strain and effective stiffness landscape along the lattice. As a result, the linear wave dispersion relationships of the system are altered, and in this process, we witness the emergence of another band gap in the higher frequency regime. We report that this upper band gap transitions from topologically trivial to nontrivial states by changing the twist angle in time, and therefore, facilitates a robust state transfer in the lattice from one side of the lattice to the other. We numerically show such efficient boundary state transfer in the higher frequency regime and evaluate the transfer fidelity.
Notably, we find that such state transfer observed in the upper band gap cannot be achieved in the lower band gap, since it preserves its topologically nontrivial characteristics at any twist angle. This implies that by leveraging the coupled dynamics in our origami system, we can realize very distinctive energy management capabilities in different frequency regimes. Thus, our origami system hints at an efficient and controllable way to manipulate multiple wave phenomena hosted within the single topological mechanical metamaterial by combining the concepts of topology and origami.
Results and discussion
Physical set-up and mathematical model
We employ the geometrical and kinematic parameters shown in Fig. 1a to describe the Kresling-patterned unit cell41. The unit cell has two degrees of freedom: translation along z-axis (u) and rotation about z-axis (φ). As the unit cell gets compressed (i.e., u changes), the top surface rotates (φ varies), therefore exhibiting coupled behavior. The resultant force–displacement relationship under pure axial compression (i.e., no external torque applied) in the experiment is shown in Fig. 1b, denoted as a red dashed line.
To model this coupled folding behavior, we employ a truss model39 by replacing the creases along segments \(\overline{AB}\) and \(\overline{AC}\) (denoted by red and blue solid lines in Fig. 1a) with linear spring elements, and segment \(\overline{AD}\) (green solid line in Fig. 1a) with a linear torsion spring. The model gives the total potential energy expressed as
where Np is the number of vertices of the polygonal cross-section, ka and kb are the linear spring coefficients of the axial spring elements along \(\overline{AB}\) and \(\overline{AC}\), respectively, and kψ is the torsion spring coefficient of the element along \(\overline{AD}\). The a and b are the lengths of the element \(\overline{AB}\) and \(\overline{AC}\), and ψ is the angle between the horizontal surface and the triangular facet (e.g., △ACD), which are functions of u and φ (see Supplementary Note 1 for the explicit expressions). The subscripted values a0, b0, and ψ0 correspond to their initial lengths and angle. F is the axial force along z-axis, and T is the torque about z-axis.
By applying the principle of minimum potential energy, we obtain F and T as a function of u and φ (see Supplementary Note 1). This analytical force–displacement relationship is shown in Fig. 1b, denoted as a blue solid line. Here, the spring coefficients are empirically determined using the least-square method to fit the model curve with the experimental curve. As a result, we can see the model agrees well with the experimental force–displacement curve. Note that the slopes of the experimental and analytical force–displacement curves—representing the stiffness of the system—are also in agreement as shown in the inset figure of Fig. 1b.
Having the mathematical model for the unit cell, we now consider the 1D dimer lattice consisting of two different types of unit cells: one with positive chirality \({\theta }_{0}^{(1)} > 0\) and the other with negative chirality \({\theta }_{0}^{(2)} < 0\). Figure 1c shows the dimer lattice, where positive chirality unit cells (red-colored) and negative chirality unit cells (blue-colored) are connected through the polygonal separator, which has mass m and rotational inertia j about z-axis. (See also the “Methods” section for the actual setup).
If Kresling unit cells serve as inter-polygonal springs while having negligible mass and inertia compared to the separators (see Supplementary Table 1), we obtain the equations of motion of the dimer Kresling lattice,
where un, vn and φn, ϑn are axial displacement and rotational angle of the odd- and even-numbered polygonal separators respectively. The subscripts 1 and 2 of the force and torque functions correspond to the positive and negative chirality unit cells. Figure 1d shows a schematic of the mathematical model of this coupled system, where the mass and rotational inertia are considered separately, such that the two lattices are connected to each other with nonlinear springs to represent the coupled nature.
Tunable wave dispersion relationship
From now on, we consider the dimer Kresling lattice with opposite and equal magnitude chirality, namely odd- and even-numbered Kresling unit cells exhibit \({\theta }_{0}^{(1)}=| {\theta }_{0}|\) and \({\theta }_{0}^{(2)}=-| {\theta }_{0}|\). For the rest of the geometrical parameters of the unit cells, we take them to be equal among odd- and even-numbered units (\({h}_{0}^{(1)}={h}_{0}^{(2)}={h}_{0}\) and R(1) = R(2) = R). Our interest is the dynamics of small amplitude elastic waves, and therefore, we start by linearizing Eq. (2):
where α and β are the linear coefficients of the positive and negative chirality unit cells, respectively (see Supplementary Note 2 for the detail). Furthermore, we substitute the Bloch wave solution in Eq. (3) and perform the Fourier transformation to get the eigenvalue problem,
where k and ω are the wave number and angular frequency, respectively; \({\hat{D}}_{k}\) is the dynamical matrix and \({{{{{{{{\bf{u}}}}}}}}}_{k}={(\sqrt{m}{u}_{k},\sqrt{m}{v}_{k},\sqrt{j}{\varphi }_{k},\sqrt{j}{\vartheta }_{k})}^{T}\) is the eigenvector. The solution to this eigenvalue problem gives the wave dispersion relationship ω(k) vs. k.
First, we analyze the dispersion relationship of this lattice under natural conditions, namely without any applied twist (i.e., zero twist angle; see Fig. 2a). Figure 2c shows the wave dispersion relationship with the unit cell geometrical parameters h0 = 30 mm, R = 36 mm, \({\theta }_{0}^{(1)}=7{0}^{\circ }\), and \({\theta }_{0}^{(2)}=-7{0}^{\circ }\) (see Supplementary Note 2 for the value of α and β). The color intensity of each branch represents the axial polarization factor Pu of the corresponding eigenvector uk (see Supplementary Note 3 for further discussion).
In this coupled 1D system, we can observe four branches: two lower and two upper branches (see the enlarged view in Fig. 2d; two lower branches are almost collapsing onto each other)42. Note that at k = π/h0 there is a degeneracy between the two lower and the two upper branches. Between the upper and the lower branches (i.e., second and third branches), we see a wide band gap denoted as band gap 1 (BG1) in Fig. 2c. Notably, this band gap emerges due to only the opposite chirality in our system [i.e., α12 = −β12 in Eq. (4)], without the necessity of dimerizing axial or rotational stiffness (i.e., without changing any geometric parameters along the lattice to alter α11 and β11). Alternating chirality itself introduces a band gap in the dispersion relation, and this is a key feature of our system distinctive from previous studies43,44.
Now, we explore the in-situ tunability of the wave dispersion relationship, without replacing or changing the unit cell design, but by just twisting the lattice. Here, we assume that the lattice has an even number of unit cells in total (see Supplementary Notes 4 and 5 for more information). Interestingly, if we quasi-statically twist the lattice along the z-axis without changing the total length of the lattice (i.e., the fixed boundary at both ends), we can change the strain landscape of the lattice. For instance, starting from the natural configuration (Fig. 2a), as we twist the lattice in the positive φ direction, we can see that the negative chirality unit cells (blue-colored unit) are elongated and the positive chirality unit cells (red-colored unit) are compressed, as shown in Fig. 2b (see also Supplementary Note 4, Supplementary Figs. 1 and 2, and Supplementary Movies 1 and 2 for further insights). Notice that if the total length of the lattice is kept constant, the lattice constant of the supercell (i.e., a pair of unit cells) is also kept constant throughout the twisting process.
Recall that the unit cell exhibits a nonlinear static response. Thus the elongated unit cells and the compressed unit cells show different instantaneous stiffnesses, which alters the effective linear stiffnesses α and β. This, in turn, results in the different linear dynamics of the lattice without replacing the unit cells. Figure 2e shows the linear wave dispersion relationships for three different twist angles per supercell: \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=(-2{5}^{\circ },\,{0}^{\circ },\,2{5}^{\circ })\). In the lower frequency regime, either positively or negatively twisting the lattice induces the first branch to shift slightly downward and the second branch to shift significantly upward. As a result, the degenerate point at k = π/h0 disappears, and the BG1 becomes narrower. In the higher frequency regime, we see that an additional band gap labeled band gap 2 (BG2) opens between the third and fourth branches (see also Supplementary Movie 3). Strikingly, the topological nature of these band gaps is highly distinctive, as will be discussed next. We note in passing that the analysis above is specific to the lattice with an even number of unit cells, which shows symmetric behavior when twisted positively and negatively. See Supplementary Notes 4 and 5, Supplementary Figs. 1 and 2 for the comparison between the lattices with even and odd numbers of unit cells.
Topological characterization
For the topological characterization of the system, we first show that the dynamical matrix \({\hat{D}}_{k}\) can be written as
where \(\hat{P}\) is the symmetry operator (please see Supplementary Note 5 for the detail). In the absence of degeneracies, the Zak phase of a band can be obtained by accumulating the phase resulting from the corresponding eigenvectors all over the first Brillouin zone (BZ; Fig. 2e). If we discretize the BZ with K points, the Zak phase for mth isolated band is defined as45,46
Here, the band index runs from m = 1 to 4. Except for the case of natural condition (i.e., zero twist angle; see below) the four bands in the dispersion relation do not have a degenerate point aside from the origin (k = 0). Therefore, we directly apply Eq. (6) to obtain the Zak phases of the bands, which are labeled in the left and right panels of Fig. 2e, respectively. Indeed the Zak phases of the four bands take the values 0 or π, while interestingly enough, these values are switched for the negatively and positively twisted lattices. To topologically characterize the band gaps, we sum the Zak phases below the corresponding band gaps47.
We find in Fig. 2e that for both negatively and positively twisted lattices, the BG1 holds a sum of Zak phases π, which indicates that it is a topologically nontrivial band gap, a property that does not change with the value and sign of the twisting angle. Special treatment is needed for the case of zero twist angle because the bands degenerate at the end of BZ (k = π/h0) and therefore Eq. (6) cannot be used. For such a case, we obtain the topological index for the band's mth and (m + 1)th (that are degenerated at some point) together via many band Berry phases (Wilson-loop eigenvalues)46,48, such that
In our system, we calculate that ϕ1,2 = ϕ3,4 = π under the natural condition. We may thus conclude that BG1 is nontrivial even for the case of zero applied twisting.
Now, for BG2, the sum of the Zak phase below BG2 is π for the negatively twisted lattices and 0 for the positively twisted lattices. This implies that the BG2 exhibit a topological phase transition (from nontrivial to trivial) as the twist angle varies from negative to positive. In the special case of zero twists, the gap closes. This distinctive topological nature of the BG2 as a function of the applied twisting angle enables the topological state transfer across the lattice, as will be discussed and verified in the following sections.
Emergence of boundary states in finite lattice under fixed boundary conditions
Due to the principle of bulk-boundary correspondence18, topologically nontrivial band gaps, identified in the infinite lattice, host topologically protected boundary states when the lattice is finite. To study the emergence of boundary states at both BG1 and BG2, we calculate the eigenfrequencies and eigenmodes of our dimer Kresling lattice, as a function of the twisted angle \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}\), for an even number of unit cells (please see Supplementary Note 6.2, Supplementary Fig. 3 for the odd number of unit cell case.). Throughout the paper, we employ fixed boundary conditions at both ends since only this choice can guarantee that the total length of the lattice remains unchanged under twisting and can also keep the lattice twisted at a certain angle. For instance, if we twist the lattice and release one end such that the boundary condition is fixed-free, then the lattice recoils back to the natural condition where the lattice is not twisted.
Figure 3a summarizes the transition of the cutoff frequencies and boundary state frequencies of the finite lattice with 16 unit cells, as a function of twist angle \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}\in [-3{0}^{\circ },3{0}^{\circ }]\). The color intensity of the lines corresponds to the localization index (LI) inspired by the inverse participation ratio (IPR)49 and the center of mode (CoM)29:
where u is the eigenvector, K is the commutation matrix, and w is the weighting vector (see Supplementary Note 6.1). The power ∘2 denotes Hadamard power. If the eigenmode is skewed toward left (right), then LI → − 1 (LI → 1). Note that each entry of u∘2 is proportional to the axial and rotational component of the kinetic energy of each polygonal separator. Therefore, the localization index corresponds to the location of the energy intensity. To closely examine the boundary states and their eigenmodes, the enlarged views of the boundary states in BG1 and BG2 are shown in Fig. 3b, c, respectively. Also, their eigenmodes are plotted in both axial and rotational components in Fig. 3d–g.
In BG1, two boundary modes can be observed for all the values of the twisting angle. This complies well with the fact that BG1 is topologically nontrivial for all the values of twisting (i.e., does not undergo a topological transition as a result of twisting). At the special case of no twisting, \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=0\), their frequencies are almost identical and closely degenerate. Their eigenmodes for this case are shown by labels (i) in Fig. 3d, e, where we see non-negligible amplitude at both ends of the lattice. When the lattice is twisted positively or negatively, one of the modes shows a decrease in frequency while the other increases. If we extract these 15th and 16th modes along these transition curves as denoted in Fig. 3b, we can see the highly localized boundary states at either end of the lattice for any \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}\). Notice that for the 15th mode, the edge state is at the right boundary for the negative twist angle (label (ii) in Fig. 3d), and changes to the left boundary when twisted positively (label (iii) in Fig. 3d). Similarly, for the 16th mode shown in the right panel of Fig. 3d, the edge state changes its localization site from left to right as the twist angle transitions from negative to positive.
In BG2, see Fig. 3c, we observe one boundary mode localized at the left boundary for negative twist angles, as shown in the profiles labeled as (vi) in Fig. 3f, g. In contrast to the boundary modes of the BG1, this mode is less localized, i.e., it has a smaller localization length, due to the smaller width of the BG2. Increasing the twisting angle \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}\), the mode becomes more and more extended till we pass \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=0\), where the band gap becomes extremely narrow for the finite lattice (the band gap closes for the infinite lattice). For the finite case, at this point, the mode transforms into the bulk mode shown in the label (vi) in Fig. 3f, g. Passing to positive twist angles, the mode starts again to be localized, but this time on the right boundary of the lattice, see (viii) in Fig. 3f, g. Since BG2 undergoes a topological transition with the twist angle, we witness the appearance and disappearance of the edge state for a particular boundary. The edge state disappears from the left boundary and appears on the right as the twist angle goes from negative to positive.
Experimental demonstration of lower frequency regime dynamic response
To examine the practicality of our analysis, we now experimentally observe the eigenmodes of the system, especially in the lower frequency regime f ∈ (0, 180] Hz, in which the topological boundary mode frequencies lie within. The upper-frequency regime f ∈ (180, 220] Hz, which hosts the upper brunches and the boundary modes of the BG2, is hindered by an excessive amount of dissipation and their experimental observation was not possible. We construct the lattice consisting of 16 unit cells (8 positive and 8 negative chirality cells) made of polyethylene terephthalate (PET) sheet (see the “Methods” section, Supplementary Note 7, and Supplementary Fig. 4 for the details). The initial conditions under consideration are: (i) natural state where \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}={0}^{\circ }\) and (ii) twisted state where \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=1{5}^{\circ }\). The chirp signal with different frequency ranges is applied via a vibration shaker, and the polygonal separator motion is measured and extracted through the digital image correlation technique.
In Fig. 4a–d, we show the dispersion relationships extracted by performing the fast Fourier transform (FFT) to the experimental results of the aforementioned two conditions, along with their corresponding analytical predictions. The experimentally obtained dispersion relationships coincide with the analytical predictions denoted as red and blue dashed lines, regardless of the twist angle. We can clearly see the expansion of the frequency regime covered by the lower two dispersion curves, by comparing Fig. 4a, b. Figure 4c, d show the FFT results of the excitation within BG1, specifically at f ∈ [100, 200] Hz. First, at the zero twist angle, we can clearly see a high-intensity region near f = 158 Hz (Fig. 4c), which is slightly higher than the eigenanalysis prediction at f ≈ 147 Hz, denoted as an open circle. Similarly, at \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=1{5}^{\circ }\) shown in Fig. 4d, the high-intensity region of FFT lies near f = 142 Hz. The eigenanalysis in this case predicts the mode frequency to be f ≈ 144 Hz, which is slightly overestimated. Although there are minute disparities in boundary mode frequencies between analytical prediction and experimental results, these FFT results still suggest the clear mode excitation within the band gap. Moreover, the decreasing behavior of the boundary mode frequency as a function of twist angle is present in both eigenanalysis and the experiment.
For closer examination, we extract the axial displacement component of the normal mode with an aid of dynamical mode decomposition (DMD) based on the singular value decomposition (SVD)50. First, we extract the fourth mode of the natural condition in Fig. 4e. When the lattice is under natural condition, the experimental results (circle symbol with blue solid lines) qualitatively follow the profile of analytical prediction (square symbol with red solid lines), except for the spatial decay of the amplitude toward the right end of the lattice. We believe that this is due to the energy dissipation in the experiment, where the lattice is excited at the left end (see Supplementary Note 8, Supplementary Fig. 5 for a numerical investigation with a dash-pot model). Similarly, in Fig. 4f, the experimental (analytical) profile of the eighth mode under the twist of \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=1{5}^{\circ }\) is shown in the blue (red) line, showing the agreement between experimental and analytical results.
Within the band gap, the linear analysis predicts the localization at the left end for the 15th mode (red line in Fig. 4g). If we extract the normal mode near f = 158 Hz from the experimental result (where FFT shows high intensity in Fig. 4c), we see the equivalent localization phenomenon as the blue solid line in Fig. 4g shows. Recall that our eigenanalysis in the previous sections identified the mode inside the BG1 as topological mode regardless of the twist angle. This implies that the experimentally observed normal mode in Fig. 4g is a topological mode, which is induced solely by dimerizing the coupled nature. For other normal modes extracted from experimental results, see Supplementary Note 8 and Supplementary Fig. 5.
Numerical investigation of topological state transfer
Now, we explore the evolution of the topologically localized modes in BG1 and BG2 as the lattice is twisted over time. Inspired by the works of state transfer in odd-sized quantum32 and classical37 Su–Schrieffer–Heeger (SSH) lattices, and the similar behavior of the boundary modes in BG2, we consider the case of an odd number of separators (even number of unit cells). The overall objective here is to explore the possibility of the in-situ boundary state transfer from one end of the lattice to the other as we apply a twisting on the lattice. For that, we numerically solve the fully nonlinear equations of motion of our dimer origami system [Eq. (2)] consisting of 32 unit cells, pre-rotated for the total twist angle of φb = −240° (equivalent to the supercell twist angle \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=-1{5}^{\circ }\)). The protocol we follow consists of two phases: (1) the excitation and (2) the loading phase. First, we apply at the left boundary a sinusoidal signal to excite the boundary mode in BG1 (BG2), which is located at f = 147.8 Hz (200.4 Hz). This excitation phase lasts 10 s (i.e., t ∈ [ −10, 0]). In the loading phase, we halt the boundary driving signal and gradually twist the lattice at the assigned twist rate until the twist angle reaches φb = 240° (\({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=1{5}^{\circ }\)). (See Supplementary Table 1 for the detail of the numerical values.) We employ a loading protocol that initiates and terminates smoothly, to avoid the excitation of other modes. The boundary angle profile φb is expressed as
where T is the total loading time, and the superscripts (0) and (1) refer to the initial and final state. Note that C1 continuity at \({\varphi }_{{\mathrm {b}}}={\varphi }_{{\mathrm {b}}}^{(0)}\) and \({\varphi }_{{\mathrm {b}}}={\varphi }_{{\mathrm {b}}}^{(1)}\) guarantees the smooth initiation and termination of the loading. The loading phase, and thus the function Eq. (9), is defined in the time domain t ∈ [0, T]. Generally, we employ large loading times T (T = 80 s in this study) to guarantee the quasi-adiabatic evolution which is necessary to avoid the excitation of other modes during the process.
Figure 5a, b show the numerically solved velocity field in the axial component (see Supplementary Note 9, Supplementary Fig. 6 for rotational component) for BG1 and BG2 respectively. For better visibility, we numerically estimate the envelope function of the velocity field using the Hilbert transform (see also Supplementary Note 9). For the case of BG1 (Fig. 5a), only the first polygonal separator shows a large amplitude, while the motions of the other separators are negligibly small regardless of the twist angle. For the case of BG2 (Fig. 5b), however, we observe the interesting phenomenon of the energy transfer through the lattice, showing the high-intensity region traveling from the left to the right end of the lattice as we gradually apply the rotation.
If we compare the mode shapes extracted at t = 0, 40, and 80 s (corresponding to φb = −240°, 0°, and 240°), we can evidently see the different behavior of the energy management between BG1 and BG2. For the extracted mode shapes of BG1 (denoted by blue solid lines with open squares in Fig. 5c–e), we always observe the localization of energy on the left end. This is in agreement with the previous analysis in Fig. 3 (also reprinted in the inset panel of Fig. 5a) that all these modes are sitting on the eigenmode transition curve in the consistent red color, which represents the preservation of the localization index LI (i.e., localization in the left end).
In the case of BG2, however, we observe the transfer of the edge mode from the left to the right boundary, as shown in Fig. 5c–e (denoted as red solid lines with open circle). At φb = −240° and 240°, the boundary states clearly show the localization on the left and right end of the lattice, respectively, which decays exponentially as presented in Fig. 5c, e. As noted before, during the transition between these two angles, the normal mode can exhibit sinusoidal-like bulk mode profile (Fig. 5d) when quasi-static torsion is absent (φb = 0°). This normal mode is reminiscent of those shown through linear eigenanalysis in Fig. 3f, and it is the mode that plays as a vehicle to transfer the energy through the lattice between the two localized modes. This can be confirmed by the eigenmode transition curve in the sub-panel of Fig. 5b, where we evidently see the change of the color—from red to blue, representing the migration of the localization index LI—along the curve. (See also Supplementary Movie 4 for the comparison between BG1 and BG2 cases.)
To quantify and confirm the state transfer from one edge to another, we define the fidelity \({{{{{{{\mathcal{F}}}}}}}}\) via the dot product32,51,
where \({{{{{{{\bf{u}}}}}}}}={({u}_{1},{v}_{1},{\varphi }_{1},{\vartheta }_{1},\cdots ,{u}_{N},{v}_{N},{\varphi }_{N},{\vartheta }_{N})}^{{\mathrm {T}}}\) is the normal mode vector based on the envelope function extracted through Hilbert transform (see Supplementary Note 9). The subscript target refers to the analytically predicted normal mode at φb = 240°, which corresponds to the excited eigenfrequency. Note that when the numerically solved normal mode vector u is similar to the analytical prediction utarget, we obtain \({{{{{{{\mathcal{F}}}}}}}}\to 1\).
Figure 5f shows the fidelity as a function of time for the cases shown in Fig. 5a, b in the loading phase, t ∈ [0, 80] s. In terms of transfer fidelity, we can even clearly see that the boundary state in BG2 transfers robustly and efficiently from left to right (\({{{{{{{\mathcal{F}}}}}}}}=0\) to \({{{{{{{\mathcal{F}}}}}}}}=1\), denoted as a red solid line). The fidelity smoothly increases and saturates to \({{{{{{{\mathcal{F}}}}}}}}\approx 1\). In contrast, as suggested by the velocity field shown in Fig. 5a, the fidelity for the case of BG1 is always zero throughout the simulation. Further investigations on the fidelity in relation to the loading protocol and total loading time can be found in Supplementary Note 9, Supplementary Fig. 7.
This numerical investigation shows highly distinctive characteristics of energy management between BG1 and BG2. Unlike the boundary states in BG1, the emerging boundary state in BG2 shows the continuous transition from localized and bulk mode profiles, which in turn enables the topological state transfer of the intended boundary mode. This is consistent with the finding in the section “Emergence of boundary states in finite lattice under fixed boundary conditions” that BG1 is topologically robust without changing its nature, while BG2 shows topological transition from non-trivial to trivial when the lattice is twisted. We thus verify two distinctive wave dynamics phenomena that can be achieved in the same setting of the versatile Kresling origami platform: robust preservation vs. transfer of the energy localization, simply by changing the boundary condition.
Conclusion
In conclusion, we have analytically, numerically, and experimentally explored the wave dynamics of the dimer Kresling lattice in relevance to the tunable wave dispersion relationships and topological boundary states. By stacking two origami unit cells of opposite chirality along a lattice, a topological band gap (BG1) emerges in the dispersion diagram. We experimentally verify the existence of topological edge modes inside the band gap. Furthermore, under quasi-static torsion given to the lattice, each unit cell exhibits the variable effective linear stiffness, which results in the tunable linear wave dispersion relationships. Such in-situ tuning opens an additional band gap (BG2) in the dispersion diagram. While BG1 always stays open and topologically non-trivial, BG2 transitions from a topologically nontrivial to a trivial regime only by changing the twist in the lattice from negative to positive. As a consequence, a finite length lattice shows the appearance and disappearance of an edge state from the boundary. We have utilized this fact to facilitate the topological state transfer by varying the twist angle in time. The transfer fidelity has shown to be extremely high, especially for the loading protocol initiating smoothly and relatively in a gradual manner. Interestingly, while efficient state transfer has shown in BG2, the boundary state in BG1 stays on one end even under the quasi-static torsion. Consequently, by the virtue of rich topological characteristics, we have demonstrated two distinct wave manipulation strategies in a single design of 1D lattice: highly robust energy confinement capability in BG1, and the highly efficient energy transfer in BG2. This has been achieved simply by changing the boundary condition, without altering the pre-configuration of the system or employing complex active mechanisms. Therefore, our system combines the concept of topology and origami to offer a unique way to harness the multi-degree-of-freedom of an elastic metamaterial for the purpose of extremely versatile and controllable energy management.
Methods
Fabrication and experiment
The Kresling unit cells are fabricated with a polyethylene terephthalate (PET) sheet of 0.254 mm thickness, cut into the petal-like folding pattern (see Supplementary Note 7 and Supplementary Fig. 4 for further information on the design) by the laser cutting machine (Universal Laser Systems, Inc. VLS4.60). After the laser-cut, we fold and assemble the unit cell by hand (see Supplementary Movie 5 for the detail of the fabrication process). Every crease line is replaced with the compliant mechanism with the discorectanglular shape perforation to accurately fold the crease lines (see Supplementary Note 7 for more detail).
Figure 6a, b, show the fabricated Kresling unit cells of positive and negative chirality, respectively. We then assemble the dimer lattice with 16 unit cells as in Fig. 6c, with spherical markers attached to the vertices of hexagonal separators. The initial conditions under consideration are: (i) natural state where \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}={0}^{\circ }\), and (ii) twisted state where \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=1{5}^{\circ }\). Here, we choose \({\overline{\varphi }}_{{{{{{{{\rm{b}}}}}}}}}=1{5}^{\circ }\) due to the limitation of our experimental set-up design, which allows the total twist angle up to φ = 120° for the 8-supercell lattice.
The assembled lattice is connected to the shaker (Büel & Kjær LDS V406 Shaker; see Fig. 6d) and controlled via a function generator (Keysight Technologies, Inc., Agilent 33220A Function/Arbitrary Waveform Generator). The lattice under vibration is then recorded with two high-speed cameras (Kron Technologies, Inc., Chronos 1.4), which capture the left-half and right-half of the lattice separately but frames being synchronized. Note that the markers facing the front side are colored green to facilitate motion tracking. The recorded videos are post-processed via digital image correlation to extract the time series data of each marker.
Numerical methods
To obtain the numerical solutions, the fully nonlinear equations of motion of the Kresling lattice [Eq. (2)] are solved numerically using in-house FORTRAN-based simulation code. For time marching, we use the Runge–Kutta–Fehlberg method with time step size dt = 10−6 s. All numerical values are treated as double-precision floating-point values for accuracy. For other numerical values used in the numerical simulation, see Supplementary Table 1.
Data availability
Data supporting the findings of this study are available from the corresponding author on request.
Code availability
Computer code written and used in the analysis is available from the corresponding author as per requested.
References
Hussein, M. I., Leamy, M. J. & Ruzzene, M. Dynamics of phononic materials and structures: historical origins, recent progress, and future outlook. Appl. Mech. Rev. 66, 040802 (2014).
Bertoldi, K., Vitelli, V., Christensen, J. & Van Hecke, M. Flexible mechanical metamaterials. Nat. Rev. Mater. 2, 1–11 (2017).
Surjadi, J. U. et al. Mechanical metamaterials and their engineering applications. Adv. Eng. Mater. 21, 1800864 (2019).
Miniaci, M., Krushynska, A., Bosia, F. & Pugno, N. M. Large scale mechanical metamaterials as seismic shields. N. J. Phys. 18, 83041 (2016).
Krushynska, A. O., Miniaci, M., Bosia, F. & Pugno, N. M. Coupling local resonance with Bragg band gaps in single-phase mechanical metamaterials. Extreme Mech. Lett. 12, 30–36 (2017).
Li, Y., Baker, E., Reissman, T., Sun, C. & Liu, W. K. Design of mechanical metamaterials for simultaneous vibration isolation and energy harvesting. Appl. Phys. Lett. 111, 251903 (2017).
Wu, L. et al. Mechanical metamaterials for full-band mechanical wave shielding. Appl. Mater. Today 20, 100671 (2020).
Liu, K. et al. 4D printed zero Poisson’s ratio metamaterial with switching function of mechanical and vibration isolation performance. Mater. Design 196, (2020) https://doi.org/10.1016/j.matdes.2020.109153.
Zhang, Q., Guo, D. & Hu, G. Tailored mechanical metamaterials with programmable quasi-zero-stiffness features for full-band vibration isolation. Adv. Funct. Mater. 31, 2101428 (2021).
Babaee, S., Viard, N., Wang, P., Fang, N. X. & Bertoldi, K. Harnessing deformation to switch on and off the propagation of sound. Adv. Mater. 28, 1631–1635 (2016).
Bilal, O. R., Foehr, A. & Daraio, C. Reprogrammable phononic metasurfaces. Adv. Mater. 29, 1700628 (2017).
Li, G.-H., Wang, Y.-Z. & Wang, Y.-S. Active control on switchable waveguide of elastic wave metamaterials with the 3D printing technology. Sci. Rep. 9, 16226 (2019).
Jin, L. et al. Guided transition waves in multistable mechanical metamaterials. Proc. Natl Acad. Sci. USA 117, 2319–2325 (2020).
Yang, H. & Ma, L. Multi-stable mechanical metamaterials by elastic buckling instability. J. Mater. Sci. 54, 3509–3526 (2019).
Deng, B., Raney, J. R., Bertoldi, K. & Tournat, V. Nonlinear waves in flexible mechanical metamaterials. J. Appl. Phys. 130, 040901 (2021).
Roman, S. & Sebastian, D. H. Observation of phononic helical edge states in a mechanical topological insulator. Science 349, 47–50 (2015).
Wang, P., Lu, L. & Bertoldi, K. Topological phononic crystals with one-way elastic edge waves. Phys. Rev. Lett. 115, 104302 (2015).
Hasan, M. Z. & Kane, C. L. Colloquium: topological insulators. Rev. Mod. Phys. 82, 3045–3067 (2010).
Ozawa, T. et al. Topological photonics. Rev. Mod. Phys. 91, 015006 (2019).
Ma, G., Xiao, M. & Chan, C. T. Topological phases in acoustic and mechanical systems https://www.nature.com/articles/s42254-019-0030-x (2019).
Thouless, D. J. Quantization of particle transport. Phys. Rev. B 27, 6083–6087 (1983).
Kraus, Y. E., Lahini, Y., Ringel, Z., Verbin, M. & Zilberberg, O. Topological states and adiabatic pumping in quasicrystals. Phys. Rev. Lett. 109, 106402 (2012).
Verbin, M., Zilberberg, O., Lahini, Y., Kraus, Y. E. & Silberberg, Y. Topological pumping over a photonic Fibonacci quasicrystal. Phys. Rev. B 91, 064201 (2015).
Zilberberg, O. et al. Photonic topological boundary pumping as a probe of 4D quantum Hall physics. Nature 553, 59–62 (2018).
Rosa, M. I., Pal, R. K., Arruda, J. R. & Ruzzene, M. Edge states and topological pumping in spatially modulated elastic lattices. Phys. Rev. Lett. 123, 034301 (2019).
Chen, Z. G. Z., Tang, W., Zhang, R. Y., Chen, Z. G. Z. & Ma, G. Landau–Zener transition in the dynamic transfer of acoustic topological states. Phys. Rev. Lett. 126, 054301 (2021).
Chaunsali, R., Li, F. & Yang, J. Stress wave isolation by purely mechanical topological phononic crystals. Sci. Rep. 6, 30662 (2016).
Oudich, M., Deng, Y., Tao, M. & Jing, Y. Space–time phononic crystals with anomalous topological edge states. Phys. Rev. Res. 1, 033069 (2019).
Grinberg, I. H. et al. Robust temporal pumping in a magneto-mechanical topological insulator. Nat. Commun. 11, 974 (2020).
Xu, X. et al. Physical observation of a robust acoustic pumping in waveguides with dynamic boundary. Phys. Rev. Lett. 125, 253901 (2020).
Xia, Y. et al. Experimental observation of temporal pumping in electromechanical waveguides. Phys. Rev. Lett. 126, 095501 (2021).
Mei, F., Chen, G., Tian, L., Zhu, S.-L. & Jia, S. Robust quantum state transfer via topological edge states in superconducting qubit chains. Phys. Rev. A 98, 012331 (2018).
Longhi, S. Topological pumping of edge states via adiabatic passage. Phys. Rev. B 99, 155150 (2019).
Longhi, S., Giorgi, G. L. & Zambrini, R. Landau–Zener topological quantum state transfer. Adv. Quantum Technol. 2, 1800090 (2019).
Estarellas, M. P., D’Amico, I. & Spiller, T. P. Topologically protected localised states in spin chains. Sci. Rep. 7, 42904 (2017).
Lang, N. & Büchler, H. P. Topological networks for quantum communication between distant qubits. npj Quantum Inf. 3, 47 (2017).
Brouzos, I., Kiorpelidis, I., Diakonos, F. K. & Theocharis, G. Fast, robust, and amplified transfer of topological edge modes on a time-varying mechanical chain. Phys. Rev. B 102, 174312 (2020).
Thota, M. & Wang, K. W. Tunable waveguiding in origami phononic structures. J. Sound Vib. 430, 93–100 (2018).
Yasuda, H. et al. Origami-based impact mitigation via rarefaction solitary wave creation. Sci. Adv. 5, eaau2835 (2019).
McInerney, J., Chen, B. G.-g, Theran, L., Santangelo, C. D. & Rocklin, D. Z. Hidden symmetries generate rigid folding mechanisms in periodic origami. Proc. Natl Acad. Sci. USA 117, 30252–30259 (2020).
Kresling, B. Origami-structures in nature: lessons in designing "smart” materials. MRS Proc. 1420, mrsf11–1420–oo02–01 (2012).
Yasuda, H. & Yang, J. Tunable frequency band structure of origami-based mechanical metamaterials. J. Int. Assoc. Shell Spat. Struct. 58, 287–294 (2017).
Köpfler, J., Frenzel, T., Kadic, M., Schmalian, J. & Wegener, M. Topologically protected twist edge states for a resonant mechanical laser-beam scanner. Phys. Rev. Appl. 11, 034059 (2019).
Huda, M. N., Kezilebieke, S., Ojanen, T., Drost, R. & Liljeroth, P. Tuneable topological domain wall states in engineered atomic chains. npj Quantum Mater. 5, 17 (2020).
Resta, R. Manifestations of Berry’s phase in molecules and condensed matter. J. Phys.: Condens. Matter 12, R107–R143 (2000).
Wang, H. X., Guo, G. Y. & Jiang, J. H. Band topology in classical waves: Wilson-loop approach to topological numbers and fragile topology. N. J. Phys. 21, 093029 (2019).
Xiao, M., Zhang, Z. Q. & Chan, C. T. Surface impedance and bulk band geometric phases in one-dimensional systems. Phys. Rev. X 4, 021017 (2014).
Vanderbilt, D. Berry Phases in Electronic Structure Theory: Electric Polarization, Orbital Magnetization and Topological Insulators (Cambridge University Press, 2018).
Wegner, F. Inverse participation ratio in 2+ϵ dimensions. Z. Phys. B Condens. Matter Quanta 36, 209–214 (1980).
Kutz, J. N., Brunton, S. L., Brunton, B. W. & Proctor, J. L. Dynamic Mode Decomposition: Data-Driven Modeling of Complex Systems (Society for Industrial and Applied Mathematics, 2016).
Caneva, T. et al. Optimal control at the quantum speed limit. Phys. Rev. Lett. 103, 240501 (2009).
Acknowledgements
We thank Dr. Hiromi Yasuda for the helpful discussion. We acknowledge financial support from the US National Science Foundation under Grant Nos. CAREER-1553202 and CMMI-1933729. Y.M. and J.Y. are grateful for the support of the Washington Research Foundation. R.C. acknowledges the Startup Grant provided by the Indian Institute of Science.
Author information
Authors and Affiliations
Contributions
Y.M. and J.Y. conceived the project. Y.M. conducted and carried out the numerical simulations. Y.M., C.-W.C., and R.C. explored the theoretical framework and prepared the manuscript. Y.M., C.-W.C., T.S.G., and G.Y. performed the experiment and analyzed the data. All authors extensively contributed to the work and finalizing of the manuscript. G.T. and J.Y. supervised the project.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Communications Materials thanks the anonymous reviewers for their contribution to the peer review of this work. Primary Handling Editor: Aldo Isidori.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Miyazawa, Y., Chen, CW., Chaunsali, R. et al. Topological state transfer in Kresling origami. Commun Mater 3, 62 (2022). https://doi.org/10.1038/s43246-022-00280-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s43246-022-00280-0
- Springer Nature Limited
This article is cited by
-
Design of compliant mechanisms for origami metamaterials
Acta Mechanica Sinica (2023)