Abstract
Trichoderma reesei is a widely used host for producing cellulase and hemicellulase cocktails for lignocellulosic biomass degradation. Here, we report a genetic modification strategy for industrial T. reesei that enables enzyme production using simple glucose without inducers, such as cellulose, lactose and sophorose. Previously, the mutated XYR1V821F or XYR1A824V was known to induce xylanase and cellulase using only glucose as a carbon source, but its enzyme composition was biased toward xylanases, and its performance was insufficient to degrade lignocellulose efficiently. Therefore, we examined combinations of mutated XYR1V821F and constitutively expressed CRT1, BGLR, VIB1, ACE2, or ACE3, known as cellulase regulators and essential factors for cellulase expression to the T. reesei E1AB1 strain that has been highly mutagenized for improving enzyme productivity and expressing a ß-glucosidase for high enzyme performance. The results showed that expression of ACE3 to the mutated XYR1V821F expressing strain promoted cellulase expression. Furthermore, co-expression of these two transcription factors also resulted in increased productivity, with enzyme productivity 1.5-fold higher than with the conventional single expression of mutated XYR1V821F. Additionally, that productivity was 5.5-fold higher compared to productivity with an enhanced single expression of ACE3. Moreover, although the DNA-binding domain of ACE3 had been considered essential for inducer-free cellulase production, we found that ACE3 with a partially truncated DNA-binding domain was more effective in cellulase production when co-expressed with a mutated XYR1V821F. This study demonstrates that co-expression of the two transcription factors, the mutated XYR1V821F or XYR1A824V and ACE3, resulted in optimized enzyme composition and increased productivity.
Similar content being viewed by others
Introduction
Replacing fossil fuels with environmentally clean and renewable energy sources is essential to building a sustainable society. Lignocellulosic biomass is the most abundant sustainable feedstock for biorefinery and biofuel production. Therefore, effectively utilizing lignocellulosic biomass could assist in addressing the problem1,2.
In order to use lignocellulosic biomass as raw material, it is necessary to hydrolyze lignocellulosic biomass into simple sugars using cellulase and hemicellulase. Extracellular cellulases and hemicellulases for lignocellulosic biomass degradation are produced mainly by filamentous fungi3. Especially the filamentous fungus Trichoderma reesei (teleomorph Hypocrea jecorna) is a well-known microorganism that produces large quantities of mixed extracellular cellulase and hemicellulase enzymes for the degradation of lignocellulosic biomass4,5. It has been expected to be the mainstay of commercial cellulase production, considering reports that industrial strains of T. reesei can be used to obtain up to over 80 g/L of extracellular protein4,6,7,8. Nevertheless, enzymatic hydrolysis of lignocellulosic biomass requires large amounts of lignocellulolytic enzymes, and the high cost of the enzymes is recognized as a major bottleneck in the production of lignocellulosic biofuels9,10,11,12.
One of the best solutions is to enhance enzyme production capacity and use inexpensive carbon sources such as glucose. Hence, the regulatory mechanisms of cellulase expression must be well understood. However, the cellulase expression is complexly regulated by several transcription factors (TFs), which may directly or indirectly influence cellulase gene expression13. Therefore, the specific roles of various factors and their complete regulatory network is not yet fully understood. Previous studies have demonstrated the role of various cellulase regulators. While XYR1, HAP2/3/5, ACE2, VEL1, ACE3, ARE1, CRZ1, STR1, and VIB1 are positive regulators, CRE1, ACE1, RCE1, CTF1, LAE1, and PAC1 are identified as negative regulators14,15. Cellulase gene expression requires the release of carbon catabolite repression (CCR)16. Therefore, modification of cellulase regulators by genetic technology is considered effective.
The transcriptional repressor CRE1 is a key regulator of the CCR and is known to indirectly inhibit cellulase expression in filamentous fungi in the presence of glucose16. In Trichoderma, truncation17, deletion18, or multisite-directed mutagenesis19 of cre1 alleviates the CCR. Thus, it is possible to markedly enhance the cellulase gene expression in the presence of various carbon sources such as glucose, lactose, sophorose, and cellulose20,21,22,23. In particular, either deletion or truncation of cre1 leads to partial de-repression of cellulase and hemicellulase when CRE1-mutated strains are cultured in a glucose-containing medium16,17,18,24. However, in a medium containing only glucose without inducing sugars, the CRE1 mutated strain cannot completely release the CCR. Thus, it either represses expression or neither represses nor activates cellulase or hemicellulase, resulting in low cellulase production. In addition, the repressors ace125 and rce126, as well as cre1, can be deleted to improve cellulase gene expression levels, but inducers are assumed to be necessary for expression.
In contrast, XYR1, a positive regulator required for expressing most cellulase and hemicellulase genes, led to the potential to express these genes without inducers by modification. XYR1 has a Zn(II)2Cys6-type DNA-binding domain, which binds directly to the upstream regions of the cellulase/hemicellulase genes27,28. Disruption of xyr1 leads to a cellulase-negative phenotype29, indicating that it is an essential factor for cellulase induction. XYR1 promotes increased cellulase gene expression under conditions of constitutive overexpression, whereas it does not increase cellulase production in media with glucose as the sole carbon source12. Engineering of TFs has also been implemented to increase cellulase expression. Despite artificial TFs that fuse XYR1 with other transcription factors that have been developed and attempted to produce cellulase constitutively using glucose as the sole carbon source, the protein productivity has not led to induced production30,31. The mutated XYR1V821F or XYR1A824V expressing strain expressed xylanase and cellulase even in glucose as the sole carbon source and improved protein productivity8,32,33. Nevertheless, the enzymes induced by the mutated XYR1V821F or XYR1A824V were not sufficient for the efficient degradation of lignocellulose because of their high xylanase and low cellulase composition32,33. Therefore, to produce cellulase/hemicellulases at levels similar to the induced state even in media with glucose as the sole carbon source, we presumed that it is necessary to add factors that activate cellulase expression working in cooperation with XYR1, and we searched for cooperative factors to express with mutated XYR1V821F.
The transcription activators ACE234, ACE335, and VIB136, were putative cooperative factors. In addition, CRT137,38, a cellulose-responsive transporter involved in the regulation of xyr1 gene expression, and BGLR39, a β-glucosidase activator, were considered as it.
ACE2 is a transcription factor that enhances the transcriptional activation of cbh1, cbh2, egl1, egl2, and xyn2 in T. reesei with cellulose induction34. However, ACE2 is not involved in sophorose induction. ACE2 binds to the same promoter motif shared with XYR1, and phosphorylation and dimerization are prerequisites for the binding of ACE2 to its target promoter40.
In T. reesei, ACE3 is known to be involved in cellulase production upon induction with lactose35. ACE3 interacts with XYR1 to initiate cellulase production41. The introduction of multiple gene copies of ace3 enhances cellulase gene expression and regulates xylanase gene expression35. In addition, C-terminal truncated ACE3 can induce high levels of cellulase and hemicellulase expression in non-induced conditions using glucose and further improve expression in induced conditions using lactose or glucose-sopholose mixture42,43. It shows improved induction of cellulase both in the presence and absence of an inducer. In addition, the strain overexpressing wild-type XYR1 or mutated XYR1A824V and C-terminal truncated ACE3 improved total secreted protein with lactose as the carbon source. However, when glucose was used as the sole carbon source, further overexpression of mutated XYR1A824V in addition to C-terminal truncated ACE3 did not result in further improvement42.
In T. reesei, VIB1 is also essential for cellulase production and acts as an important regulator of cellulase induction36,44. A comparison of the Δvib1 and Δxyr1 transcriptomes using cellulose as a carbon source showed a high frequency of overlap between cellulose-induced genes regulated by VIB1 and XYR1 targets45. This suggests that VIB1 partially regulates cellulase gene expression via XYR145.
CRT1 has been considered one of the most important transporters involved in cellulase induction in T. reesei37,38. Its deletion was found to completely abolish cellulase gene expression upon induction with cellulose and lactose38. Recently, CRT1 was validated to transport lactose, cellobiose, glucose, and soporose46. In addition, when XYR1 is overexpressed under glucose-containing conditions, crt1 transcription was maintained at a relatively low level47.
BGLR, a β-glucosidase activator, is a transcription factor having a Zn(II)2-Cys6-type DNA-binding domain39. One function of BGLR is to upregulate certain β-glucosidase genes39. The bglr gene deleted mutant showed increased cellulase production during cellobiose growth.
We examined whether mutated XYR1V821F and each of the five factors reportedly associated with it affect the regulation of cellulase and hemicellulase production under inducer-free conditions using glucose as the carbon source.
We used a derivative strain of PC-3-7, a high-performance enzyme-producing strain of T. reesei that is more productive and tends to be alleviated from CCR in glucose48,49,50. T. reesei is known to secrete a complete set of cellulases when cultured with inducers such as cellulose, cellobiose, and sophorose5,51. In contrast, CBH and EG activities of T. reesei are known to be higher than those of other microorganisms, but its BGL activity is lower than that of cellulase mixtures from other organisms52. This results in cellobiose accumulation and subsequent product inhibition of CBH, reducing enzymatic hydrolysis efficiency. To solve this problem, the addition of BGL is effective in improving enzyme performance. Production costs can be lowered by overexpressing the BGL in T. reesei. The E1AB1 strain has a β-glucosidase gene from Aspergillus aculeatus (Aabgl) in the PC-3-7 strain52,53,54.
We aimed to develop a strain that does not require an inducer for cellulase production using the E1AB1 as a more practical enzyme-producing strain. We attempted to express cellulase by co-expression of the candidate five factors and mutated XYR1V821F, which induces high-level xylanase production under non-inducing conditions. In this study, the defect of insufficient cellulase induction was eliminated by constitutive expression of mutated XYR1V821F and ACE3. Thus, we report that inexpensive production of saccharification enzymes can be achieved without cellulase inducers.
Results
Effects of the disruption of repressors and the constitutive expression of mutated XYR1V821F
In order to combine the expression of mutated XYR1V821F and its candidate cooperative factors, two genomic insertion sites were required to express mutated XYR1V821F and each factor. Therefore, we used the ace1 and rce1 gene regions encoding transcriptional repressors as the insertion sites.
First, disruption of the ace1 and rce1 repressor genes was performed to confirm the effect of the deletion. The results showed that protein productivity of E1AB1, Δace1, and Δrce1 strains was reduced to less than 10% under the non-inducing conditions with glucose as the carbon source compared to inducing conditions with cellulose as the carbon source in the parental E1AB1 strain (Fig. 1a). Furthermore, the disruption of ace1 or rce1 did not alter the composition of secretory proteins as depicted in Fig. 1b. A high-intensity band indicated by an open arrow was found (Fig. 1b, lanes 2–4) and was identified as a glycoside hydrolase family 55 (GH55) protein (Trire2_121746) by nano LC–MS/MS analysis. This protein was found to be similar to β-1,3-glucanase Lam55A of Phanerochaete chrysosporium (Additional file Table S1). This indicates that little cellulase production was observed in the three strains with glucose as the sole carbon source.
Effects of constitutive expression of V821F mutated XYR1 and disruption of repressors on glucose culture. (a) Extracellular protein from the cultivation of samples after 72, 96, and 120 h. Trichoderma reesei strain E1AB1 was cultivated in shake flasks on an inducing medium containing 3% cellulose, and recombinant strains E1AB1Δace1, E1AB1Δrce1, E1AB1-X (Δace1-Pact1-xyr1V821F), and E1AB1-XΔrce1 were cultivated on a non-inducing medium containing 3% glucose. (b) SDS-PAGE analysis of the secreted proteins after 72 h. T. reesei strain E1AB1 with 3% cellulose (lane 1) and 3% glucose (lane 2) cultures, and recombinant strains E1AB1Δace1 (lane 3), E1AB1Δrce1 (lane 4), E1AB1-X (lane 5), and E1AB1-XΔrce1 (lane 6) with 3% glucose cultures. Open arrowhead indicates the confirmed in glucose culture (lanes 2–4). Closed arrowheads indicate clearly overexpressed proteins, likely corresponding to the main xylanase (BXL1, XYN1, XYN2, lanes 5 and 6). The gel was cropped in the 15–250 kDa range, and the original gel was shown in the Additional file Fig. S4. Error bars indicate standard deviations. Statistical significance was determined by a two-tailed unpaired Student’s t-test. **p < 0.01.
We selected the act1 promoter as a constitutive promoter unaffected by carbon source utilization, which showed similar expression levels as pyruvate decarboxylase 1 (Trire2_121534) in RNAseq results obtained under cellulose and glucose-containing culture conditions in the E1AB1 strain54. A cassette having XYR1V821F under constitutively active act1 promoter was introduced at the ace1 locus, and the strain was named E1AB1-X. The E1AB1-X strain produced 2.08 g/L of extracellular protein under non-inducing conditions. This was a fourfold increase in extracellular protein production compared to the parental strain (Fig. 1a). In addition, differences in band patterns were observed in the SDS-PAGE analysis (Fig. 1b, closed arrowheads). Based on the estimated molecular weights and a previous report53, the protein bands likely corresponded to the main xylanases (XYN1, XYN2) and β-xylosidase (BXL1; Fig. 1b, lane 5). However, their composition was different from that of proteins produced by the parental strain E1AB1 in an inducing condition (Fig. 1b, lanes 1 and 5), and the band intensities corresponding to cellulases (CBH1, CBH2, EG1) were also low.
Thus, xylanases could be produced by constitutive expression of the mutated XYR1V821F even under inducer-free conditions; however, cellulases were not fully produced. Further rce1 gene disruption in the E1AB1-X strain resulted in increased protein productivity (Fig. 1a) but no significant changes in the enzyme composition (Fig. 1b, lane 6). Therefore, the rce1 locus was used to test the enhancement of cellulase productivity by co-expressing the candidate cooperative factors for cellulase production.
Co-expression of cellulase transcription-related factors with mutated XYR1V821F in glucose medium to enhance cellulase expression
Homologous recombination of crt1, bglr, vib1, ace2, and ace3, cellulase activators, and factors essential for cellulase expression was done at the rce1 locus of the E1AB1-X genome, followed by constitutive expression under the act1 promoter. Constitutive co-expression of CRT1, BGLR, VIB1, or ACE2 in the E1AB1-X strain resulted in no significant changes in the secreted protein concentration (Fig. 2a) and the bands with molecular weights corresponding to cellulases such as CBH1, CBH2 (Fig. 2b, lanes 2–5). In contrast, constitutively ACE3 expressing strain, E1AB1-XA3, showed a 1.5-fold increase in protein production compared to E1AB1-X (Fig. 2a). Enzyme composition analysis revealed a decreased band corresponding to xylanases (XYN1, XYN2, and BXL1) and a few bands with increased intensity, as indicated by closed arrows in E1AB1-XA3 (Fig. 2b, lane 6). These bands, as identified by nano LC–MS/MS analysis, were mainly cellulases (CBH1, CBH2, and EG1), xylanases (BXL1 and XYN4), and small amounts of proteins involved in cellulose degradation (SWO1, CIP2, and EG4) (Additional file Table S2).
Co-expression of factors involved in cellulase transcription in the E1AB1-X strain. Trichoderma reesei strain E1AB1-X was co-expressed with various factors that relate to cellulase expression and cultivated in shake flasks on a non-inducing medium containing 3% glucose. (a) Extracellular protein from cultivation samples after 96 h. (b) SDS-PAGE analysis of the secreted proteins after 72 h in a glucose culture of T. reesei E1AB1-X (lane 1, Δace1-Pact1-xyr1V821F, as control), E1AB1-XC (lane 2, Δace1-Pact1-xyr1V821F and Δrce1-Pact1-crt1), E1AB1-XB (lane 3, Δace1-Pact1-xyr1V821F and Δrce1-Pact1-bglr), E1AB1-XV (lane 4, Δace1-Pact1-xyr1V821F and Δrce1-Pact1-vib1), E1AB1-XA2 (lane 5, Δace1-Pact1-xyr1V821F and Δrce1-Pact1-ace2), and E1AB1-XA3 (lane 6, E1AB1-XA3, Δace1-Pact1-xyr1V821F and Δrce1-Pact1-ace3(PT)). The gel was cropped in the 15–250 kDa range, and the original gel was shown in the Additional file Fig. S5. (c) Volumetric enzyme activity of the 72-h culture supernatant. One unit of activity is defined as the amount of enzyme that produced 1 μmol of p-nitrophenol per minute per mL of culture supernatant from the substrate at 50 °C. Bar graphs show the activity relative to that of E1AB1-X. Error bars indicate standard deviations. Statistical significance was determined by the two-tailed unpaired Student’s t-test. **p < 0.01.
To measure the enzyme activity of the culture supernatant of the ACE3 constitutively co-expressing strain, pNPLase was measured for CBH1 activity and pNPGase for BGL activity. The results showed that the E1AB1-XA3 strain was 4.9-fold higher in pNPLase and 5.5-fold higher in pNPGase compared to the E1AB1-X strain. In the E1AB1 strain, the β-glucosidase from A. aculeatus (Aabgl1) is expressed using the egl1 promoter. The increase in pNPGase activity is suggestive of enhanced transcription of the egl1 promoter in the E1AB1-XA3 strain. These pNPGase and pNPLase activity values, which indicate cellulase activity, increased about five-fold. While the pNPXase and pNPX2ase activity values, which indicate xylanase activity, changed up to 1.8- and 0.8-folds. The fact that xylanase activity did not improve much, unlike cellulase, suggests that ACE3 contributes to a specific improvement in cellulase expression.
In addition, the band of GH55 observed under non-inducible conditions (Fig. 1b, lanes 2–4 with open arrowhead) disappeared in the supernatant of the ACE3 constitutively expressing strain. Lam55A, which hydrolyzes β-1,3-glucan, could regulate the metabolism of external nutrient sources55. Thus, it was inferred that cellulases were induced in the E1AB1-XA3 strain even in the absence of inducers, and the strain resembled the actively induced state for cellulase production. Consequently, we found that the E1AB1-XA3 strain, which combines the constitutive expression of the mutated XYR1V821F and ACE3, makes it possible to produce xylanases and a high yield of cellulases, even under inducer-free conditions.
Identification of the best combinations of factors required for high protein productivity and cellulase composition under inducer-free conditions
The E1AB1-XA3 strain had high cellulase productivity even in the absence of inducers, indicating that a combination of ACE3 and mutated XYR1V821F is effective for an increase in cellulase activity (Fig. 2). In addition to V821F mutation, the A824V mutation has been reported previously to be one of the XYR1 mutations that allow expression of xylanase and cellulase expression without inducers32. Therefore, to confirm the potentially useful XYR1 mutants, V821F and A824V mutants with a glucose-blind phenotype were evaluated along with the wild-type (Fig. 3a). In contrast, reports have suggested that there is a possibility of multiple transcription start sites in ace341,43. The ace3 of E1AB1-XA3 used in Fig. 2 was derived from the JGI genome database (The ORF sequences (651 or 629 amino acids) presented in http://genome.jgi.doe.gov/Trire2/Trire2.home.html) by reference. However, correct introns and two putative transcription start sites were proposed41,43. The estimated complete amino acid sequence was 734 amino acids, and the sequence registered in JGI was a partially truncated N-terminal DNA-binding domain. Therefore, we cloned both putative translation initiation sites from genomic DNA and examined the constitutive expression of partially truncated ACE3 (PT-ACE3) and full-length ACE3 (FL-ACE3) (More detail is provided in the Additional file Fig. S1). In addition, we performed constitutive expression of XYR1 and ACE3 using non-homologous recombination to find whether disruption of the two repressors (ace1 and rce1) was essential. The strains, carbon sources, and genotypes used in this study were listed in the Additional file, Table S3.
Confirmation of the genetic combinations required for high cellulase production under inducer-free conditions. (a) Putative domain of XYR1 and ACE3 used in the study, amino acid mutations in XYR1, and the presumed variant of ACE3. Shaking flask cultivations were performed using 3% cellulose: Lane 1 and 3% glucose: Lane 2–9. The strains used in this figure were Lane 1 and 2: E1AB1, Lane 3: E1AB1-X (Δace1-Pact1-xyr1V821F), Lane 4: E1AB1-A3 (Δrce1-Pact1-ace3(PT)), Lane 5: E1AB1-XA3 (Δace1-Pact1-xyr1V821F and Δrce1-Pact1-ace3(PT)), Lane 6: E1AB1-XA3fl (Δace1-Pact1-xyr1V821F and Δrce1-Pact1-ace3(FL)), Lane 7: E1AB1-XA3nhr (Pact1-xyr1V821F and Pact1-ace3(PT) by non-homologous recombination), Lane 8: E1AB1-X824A3nhr (Pact1-xyr1A824V and Pact1-ace3(PT) by non-homologous recombination) and Lane 9: E1AB1-XwtA3nhr (Pact1-xyr1WT and Pact1-ace3(PT) by non-homologous recombination).The carbon sources, strains, and genotypes used in this figure were organized in an Additional file, Table S3. (b) SDS-PAGE of secreted proteins after 72 h cultivation (2.5 μg-protein/lane). The gel was cropped in the 15–250 kDa range, and the original gel was shown in the Additional file Fig. S6. (c) Extracellular protein concentration at 96 h. Relative transcription levels of xyr1 (d) and ace3 (e). The real-time PCR was performed on the samples taken after 48 h. The transcriptional levels of pgk1 and E1AB1 strain on glucose culture were measured for reference calculation and data normalization, respectively, and analyzed using the ΔΔCt method. Error bars indicate standard deviations. Statistical significance was determined by a two-tailed unpaired Student’s t-test. **a indicated p < 0.01 for the test with Lane 5 (E1AB1-XA3) and **b indicated p < 0.01 for the test with Lane 7 (E1AB1-XA3nhr).
In all strains constitutively expressing ACE3, the enzymatic composition of the secreted proteins was mainly cellulase (Fig. 3b, lanes 4, 5, 6, 7, 8, and 9). The total protein production of the E1AB1-A3 strain expressing PT-ACE3 (Fig. 3c, lane 4) and the E1AB1-XwtA3 strain co-expressing ACE3 with wild-type XYR1 (Fig. 3c, lane 9) was 0.57 g/L and 0.51 g/L, respectively. These results indicated that co-expression of ACE3 with the mutated XYR1V821F was effective for high productivity. For a mutated XYR1 to be combined need not be V821F-specific but should at least exhibit a glucose-blind phenotype like mutated XYR1V821F or XYR1A824V (Fig. 3b,c, lanes 7 and 8). Furthermore, the co-expression of ACE3 was effective with partial truncated and full-length sequences, both of which had a cellulase-dominated composition and showed higher productivity than a single expression of XYR1V821F (Fig. 3b,c, lane 6). However, the productivity of the E1AB1-XA3fl strain with FL-ACE3 was 14% lower than that of the E1AB1-XA3 strain with PT-ACE3 (Fig. 3c, lane 5). This result was surprising as ACE3 with a partially truncated DNA-binding domain had superior productivity. Expression of mutated XYR1V821F and ACE3 by non-homologous recombination (Fig. 3c, Lane 7, E1AB1-XA3nhr strain) showed the same co-expression effect as above. However, the protein productivity was lower than in the ace1, and rce1 disrupted E1AB1-XA3 strains (Fig. 3c, lane 5).
The transcript levels of xyr1 and ace3 were compared in the nine strains listed in Table S3. The total xyr1 transcript was measured with primer pair at non-mutated regions and was measured for WT, V821F, and A824V specifically by designing a reverse primer at the mutated position. Primers used to measure ace3 transcripts were designed against common sequences for all ace3 and in unique sequences to full-length (exon 2) or partial truncated (within intron 2 to exon 3) (Additional file Table S4). Therefore, xyr1 transcript levels increased 11.5-fold in the E1AB1-X strain, constitutively expressing the mutated XYR1V821F compared to the parental E1AB1 strain in the medium with glucose as a carbon source. The increase was not only in xyr1V821F but also xyr1WT (native xyr1) by 4.2-fold (Fig. 3d, lanes 2 and 3). Furthermore, total ace3 transcription was increased by 6.2-fold in the E1AB1-X strain, even though ace3 expression was not directly enhanced (Fig. 3e). This indicates that the expression of native xyr1 and ace3 is significantly enhanced directly/indirectly by mutated XYR1V821F. Furthermore, in the E1AB1-XA3 strain co-expressing mutated xyr1V821F and PT-ace3, total xyr1 and ace3 transcript levels increased up to 16.8- and 8.9-fold, respectively, compared to the parent strain (Fig. 3d,e, lane 5). In the case of co-expression of xyr1WT and PT-ace3 without utilizing mutated xyr1 (E1AB1-XwtA3nhr strain), total transcript levels of xyr1 and ace3 increased 6.7-fold (Fig. 3d, lane 9) and 3.7-fold (Fig. 3e, lane 9), respectively. However, total secreted protein levels did not increase (Fig. 3c, lane 9). These results suggested that a certain level of total XYR1 or mutated XYR1, such as mutated XYR1V821F or XYR1A824V, was required for high cellulase production.
These results also indicated that constitutive expression of the mutated XYR1 exhibiting a glucose-blind phenotype (like V821F, A824V) and ACE3 (full-length and partial truncated) was necessary for high cellulase production in the absence of inducers. Additionally, the partial truncation of the DNA-binding domain of ACE3 and disruptions of ace1 and rce1 contributed to high protein productivity, and the genotype of the E1AB1-XA3 strain was found to be the most effective combination in this study.
Expression and activity analysis of cellulase and xylanase under single or co-expressed XYR1V821F and PT-ACE3
We analyzed the gene expression and activity of cellulase and xylanase in a single expression of XYR1V821F (E1AB1-X strain), a single expression of PT-ACE3 (E1AB1-A3 strain), and co-expression of XYR1V821F and PT-ACE3 (E1AB1-XA3 strain).
Owing to the effect of the XYR1V821F mutation, the transcription of major cellulases in the E1AB1-X strain was approximately four orders of magnitude higher than that of the parent strain E1AB1 (Fig. 4a). Furthermore, in the E1AB1-XA3 strain, constitutive expression of PT-ACE3 resulted in an additional 6.4-fold increase in cellulase transcript levels compared to the E1AB1-X strain (Fig. 4a). The increase in expression of the major xylanases, xyn1 and xyn2 were a maximum of 1.7-fold (Fig. 4a), which was in agreement with their enzymatic activity (Fig. 4b). Consistent with these results, the enzymes produced by the E1AB1-XA3 strain exhibited a similar amount of xylanase and a specific increase in the cellulase (CBH1, CBH2, EG1) components when compared to the E1AB1-X strain (Fig. 4c). The cellulase/xylanase composition of the E1AB1-XA3 strain in the non-induced culture using glucose was similar to that of the induced culture of the parental E1AB1 strain using cellulose (Fig. 4b, Additional file Fig. S2). In the E1AB1-A3 strain, the degrading activities of pNPX2ase and pNPXase were little detected (Fig. 4b), and the bands of BXL1, XYN1, and XYN2 could be little identified (Fig. 3b, Lane No.4). Therefore, constitutive single expression of ACE3 could activate cellulase production but could not fully activate xylanase production (Fig. 3c). Moreover, based on protein concentrations and composition estimated from SDS-PAGE, absolute amounts of CBH1, CBH2, and EG1 were 0.24, 0.34, and 1.25 g/L in the E1AB1-X, -A3, and -XA3 strains, respectively. This confirms a synergistic upregulation of cellulase upon co-expression of mutated XYR1V821F and ACE3 (Fig. 4c).
Analysis of gene expression, enzyme activity, composition, and saccharification of microcrystalline cellulose. (a) Relative gene expression of the major cellulases and xylanases. The real-time PCR was performed on the 48 h culture sample with glucose as a carbon source. The transcriptional levels of pgk1 and E1AB1-X strain RNA were measured for reference calculation and data normalization, respectively, and analyzed using the ΔΔCt method. (b) The volumetric activity of each enzyme in the culture supernatant obtained after 72 h of cultivation with glucose as the carbon source. One unit of activity is defined as the amount of enzyme that produced 1 μmol of p-nitrophenol per minute per mL culture of the supernatant from the substrate at 50 °C. Bar graphs show relative activity to E1AB1-X. (c) Concentration of each enzyme component was calculated from the enzyme composition and total secreted protein concentration. The compositions were calculated from the band patterns following SDS-PAGE (see Additional file Fig. S2) derived from E1AB1 (culturing using cellulose: C and glucose: G), E1AB1-X (G), E1AB1-A3 (G), and E1AB1-XA3 (G) strains. Protein concentrations were determined from the 96-h value. (d) Microcrystalline cellulose saccharification using the same protein dosage (2.0 mg protein/g cellulose). (e) Microcrystalline cellulose saccharification using the same volume of culture supernatant (0.87 mL culture supernatant/g cellulose). Error bars indicate standard deviations. Statistical significance was determined by a two-tailed unpaired Student’s t-test. **p < 0.01, *p < 0.05.
Saccharification of microcrystalline cellulose was evaluated using enzymes produced under inducing conditions using cellulose or under non-inducing conditions using glucose. In the evaluation using 2.0 mg-enzyme per g-cellulose, the enzyme produced by the parent strain E1AB1 induced with cellulose released the highest amount of glucose at 26.8 g-glucose/L. In contrast, the enzyme produced by strain E1AB1-XA3 was the best in the non-inducing condition with 22.5 g-glucose/L (Fig. 4d). The enzyme from strain E1AB1-A3 released 17.8 g-glucose/L. This result was 2.3-fold higher than that of the enzyme from strain E1AB1-X (Fig. 4d). We inferred that this was perhaps due to the high composition ratio of the cellulase components within the protein. However, as described above, the total amount of secreted enzymes produced by the E1AB1-A3 strain was 0.57 g/L (Fig. 4c), and the absolute amount of the cellulase was 0.34 g/L. In contrast, the enzyme cocktail derived from the E1AB1-X strain contained a protein concentration of 2.09 g/L and was more productive than E1AB1-A3, but it was mainly composed of xylanases; as a result, the absolute amount of cellulases was 0.24 g/L. Therefore, the cellulase component produced by the E1AB1-A3 and E1AB1-X strains was lower than that of the E1AB1-XA3 strain, 1.25 g/L. Therefore, saccharification was performed using 0.87 mL of the same volume of culture supernatant. The results showed that the enzyme from the E1AB1-A3 strain released 6.5 g-glucose/L, and the enzyme from the E1AB1-X strain released 7.5 g-glucose/L, with the two enzymes having comparable performance. In contrast, the enzyme from the E1AB1-XA3 strain released a significantly higher amount, 19.9 g-glucose/L (Fig. 4e). This suggests that the E1AB1-XA3 strain can produce a better enzyme than the existing XYR1V821F overexpression strain under inducer-free condition.
The E1AB1-XA3 strain was found to have two important phenotypes: increased cellulase composition ratio by constitutive expression of ACE3 and high protein productivity under non-inducing conditions by introducing mutated XYR1V821F. Thus, we could achieve the most crucial property of the cellulolytic enzyme, which is the increased cellulase production in a non-inducing production system.
Discussion
The previously reported inducer-free enzyme production system by T. reesei using mutated XYR1V821F or XYR1A824V mainly produced xylanase, with weak activation of cellulase expression32,33. Therefore, we developed a genetic modification strategy to produce both cellulase and xylanase at the same level as in induced conditions. As a result, we could successfully generate large quantities of cellulase and xylanase without inducers. Enhanced cellulase productivity using glucose as the sole carbon source was achieved by constitutive expression of mutated XYR1V821F or XYR1A824V and ACE3, especially ACE3, having a partially truncated DNA-binding domain.
In this report, co-expression of XYR1V821F with cellulase regulation-related factors, CRT1, BGLR, VIB1, or ACE2, did not increase cellulase expression (Fig. 2). Previously, the deletion of these factors was reported to cause loss or reduction of cellulase expression38,39,40,45. These factors were also affected by enhanced expression of XYR1 and ACE3 (for example, crt1 is regulated by ACE338,47). This suggested that the effect of co-expression of XYR1V821F with these factors may not have occurred because sufficient amounts of these factors were already upregulated by the constitutive expression of mutated XYR1V821F and subsequent upregulation of ACE3 (Fig. 3e, Lane No. 3). In contrast, the effect of ACE3 co-expression was observed to contribute to the improved cellulase production (Fig. 2), suggesting that it is necessary to enhance the expression of ACE3 beyond the upregulation by mutated XYR1V821F. It was previously reported that ACE4 directly binds to the ace3 promoter and regulates ACE3 expression to promote cellulase production56. Possibly ACE3 is regulated not only by XYR1 but also by other factors, including ACE4, which suggests that enhanced expression of ACE3 by factors other than XYR1 may be the key to the cellulase expression. In addition to the regulation of main cellulase/hemicellulase expression, it is also possible that minor enzymes (not under the control of XYR1 and ACE3) were not expressed, and further comprehensive expression profile analysis of various regulators and glycoside hydrolase families requires future intervention.
XYR1 has been studied as one of the key regulators of cellulase and xylanase production, but its detailed regulatory mechanism remains unclear. In our study, co-expression of wild-type XYR1 and PT-ACE3 (E1AB1-XwtAnhr strain) did not show an increase in cellulase productivity compared to the constitutively expressing PT-ACE3 (E1AB1-A3 strain) (Fig. 3). Furthermore, in an industrial strain derived from Rut-C30, cellulase production did not increase in the absence of cellulase inducers upon replacing the native xyr1 promoter with constitutive promoters, such as promoters from phosphoglycerate kinase, histone 3, and basic-leucine zipper transcription factor genes12. In contrast, overexpression of wild-type XYR1 using the copper-repressible promoter Ptcu1 in the T. reesei QM9414 strain resulted in high cellulase production in glucose-enriched cultures57. Although the act1 promoter was selected as the constitutively expressed promoter in this study, it might have been insufficient to enhance the expression level of wild-type xyr1, and possibly the cellulase could be induced by overexpression of wild-type XYR1. In contrast, expression of mutated xyr1V821F using the same act1 promoter led to remarkable xylanase production in non-inducing conditions (Fig. 1). It is also suggested that post-translational modification of XYR1 may be required for complete activation of cellulase and hemicellulase gene transcription12. Mutations in the acidic activation domain of XYR1, such as A824V or V821F, could mimic post-translational modifications and activate at least xylanase expression at lower levels than wild-type XYR1. Therefore, it was suggested that the expression profiles of cellulase/hemicellulase are different even using the same promoter strength in wild-type and mutated XYR1, and further investigation is needed to determine if the expression level of mutated XYR1V821F was optimal in this study and the effect of promoter strength to driving the wild-type/mutated XYR1.
Another modification factor, ACE3, has been shown to play an important role in cellulase regulation, but its functional analysis remains unclear. ACE3 in T. reesei NG14 and derived RUT-C30 and RL-P37 strains have an 11-amino acid truncation at the C-terminus, resulting in higher cellulase productivity42. Furthermore, Luo et al. reported high cellulase production even under inducer-free conditions by overexpression of ACE3 with C-terminal truncation of 7–17 amino acids, using the RL-P37 strain as the parent strain43. In this reported system, none of the ace3 had a complete wild-type C-terminus43. In contrast, in this study, in the E1AB1 strain derived from the PC-3–7 strain, ace3 in the genome had a complete C-terminus, and ace3 with further enhanced expression had no C-terminal mutation. However, high cellulase production was achieved under non-inducing conditions by co-expression with mutated XYR1V821F (Fig. 3a). Luo et al. suggested that the C-terminal 17 amino acids of ACE3 may be either the repressor domain itself or part of a domain that interacts with the repressor43. Our results indicated that the C-terminal mutation of ACE3 is not essential for inducer-free production of cellulase and that its interaction with mutated XYR1V821F may directly or indirectly release its inhibitory function at the C-terminus of ACE3.
In addition, Luo et al. reported that a Zn(II)2Cys6-type DNA-binding domain with all six cysteines at the N-terminus and specific mutation at the C-terminus were required for inducer-free cellulase production43. In contrast, in the present study, the expression of FL-ACE3 with a complete N-terminal DNA-binding domain enhanced cellulase productivity. However, surprisingly, PT-ACE3 with an incomplete DNA-binding domain was more productive (Fig. 3). ACE3 was proposed to form homodimers with ACE3 and heterodimers with XYR141, and constitutively express PT-ACE3 which possibly interact with native-ACE3 (having complete DNA-binding domain), PT-ACE3, native-XYR1, or mutated XYR1V821F. In addition, the transcript levels of FL-ace3 were not significantly increased under induced conditions using cellulose, and transcripts mainly corresponding to PT-ace3 increased (Fig. 3e, lane 1), supporting the previous reports43. Therefore, ACE3 with DNA binding ability is required for cellulase expression, but not necessarily to increase the expression level. It was considered that ACE3 corresponding to PT-ACE3 regulates cellulase expression through dimer formation and interactions with other factors also during cellulase production with inducers. The DNA-binding domain of ACE3 is classified as a Gal4-like Zn(II)2Cys6 binuclear cluster; Gal4 is known to bind DNA as a homodimer58. Therefore, it was speculated that homodimers with PT-ACE3 (with PT-ACE3 or native FL-ACE3), in which a part of the DNA-binding domain was truncated, lose DNA-binding ability. However, the results of the co-expression and regions of increased transcription during induced production in Fig, 3e suggested that the presence of PT-ACE3 positively regulates cellulase production. Therefore, DNA binding of ACE3 may also play a role in inhibition, depending on the state. It was also thought that heteromerization with XYR1, which can bind DNA, could activate cellulase production, but further investigation into the function of ACE3 with partial truncation of the DNA-binding domain would be needed.
The ace125 and rce126 loci used to insert xyr1V821F and other cellulase regulation-related factors were known repressors. In this study, their disruption was not essential and did not contribute to improved cellulase composition, although the total secreted protein concentration was increased (Fig. 3b,c). The enzyme productivity of the E1AB1-XA3 strain using glucose was improved compared to the E1AB1-X and E1AB1-A3 strains but slightly inferior to the parent E1AB1 strain using cellulose (Figs. 1a, 3c, 4c). This seemed to be largely dependent on the property of cellulose as a carbon source and its inducibility. Glucose is extremely easy to assimilate and is consumed rapidly; therefore, it was depleted after 48 h in this study (Additional file Fig. S3). In contrast, cellulose is not easily assimilated and degrades slowly, releasing cellobiose and glucose over a long time, and it is considered less likely to induce CCR. The E1AB1 strain used in this study is an industrial strain that has undergone repeated mutation breeding, and the cre1 mutation50 and α-tubulin (tubB) disruption54 have eliminated various suppressive regulations, including CCR. However, even in this strain, enzyme production was slight, while glucose concentrations were high (Additional file Fig. S3). Luo et al.43 also mentioned that (hemi) cellulase production only occurs after the glucose has been depleted below a certain threshold, and the CCR was not fully overcome. In the present state, the practices to avoid CCR (for example, fed-batch culture59,60) are necessary to lead to high cellulase productivity equivalent to cultures using cellulose, and constitutive expression of activators such as XYR1 and ACE3 alone cannot overcome the CCR. Therefore, further investigation of the repression mechanisms is needed in addition to modification of these activators.
Due to its high production ability, T. reesei is a promising host for heterologous protein production. However, using the conventional cellulose-based enzyme production system is difficult for heterologous protein production61,62. If the cellulase genes are replaced with genes for the proteins of interest, then cellulose cannot be decomposed, and the inducer is not released, diminishing the protein production ability. Contrarily, if cellulase is not disrupted, large amounts of native cellulases will be contaminated62. Previous reports showed heterologous protein production using xyn1 and xyn2 promoters with xyr1A824V63. However, the results of this study indicate that it has become possible to use extremely strong cellulase promoters, such as cbh1 and cbh2, for heterologous protein production without the co-production of cellulase. Such strong cellulase promoters are expected to be great productivity tools that can be used to express saccharifying enzymes for bioethanol production and various valuable proteins.
Methods
Strains and propagation
The T. reesei strains used in this investigation are listed in Table 1. T. reesei strains E1AB153 and E1AB1Δpyr4 (uracil auxotroph) were kindly provided by Prof. W. Ogasawara (Nagaoka University of Technology). Strains were maintained on potato dextrose agar (PDA; Difco Laboratories, Detroit, MI) plates.
Shake flask cultivation
For preculture enzyme production, 4 × 105 spores of each strain were inoculated into 2 mL of basal medium48 containing 1% (w/v) glucose in a 10-mL culture tube. Spores were counted using a Thoma hemocytometer (Sunlead Glass Corp.). The basal medium comprised 0.14% (w/v) (NH4)2SO4, 0.2% (w/v) KH2PO4, 0.03% (w/v) CaCl2·2H2O, 0.03% (w/v) MgSO4 7H2O, 0.1% (w/v) polypeptone, 0.05% (w/v) yeast extract, 0.1% (w/v) Tween 80, and 0.1% (w/v) trace element solution in 50 mM Na-tartrate buffer (pH 4.0). The trace element solution contained 6 mg H3BO3, 26 mg (NH4)6Mo7O24·4H2O, 100 mg FeCl3·6H2O, 40 mg CuSO4·5H2O, 8 mg MnCl2·4H2O, and 200 mg ZnCl2 in 100 mL of distilled water. Preculturing was carried out by shaking at 220 rpm, at 28 °C for 2 days. For each of the main cultures, 500 μL of the preculture was inoculated into 50 mL of basal medium containing 3% (w/v) powdered cellulose (KC FLOCK W-400G, Nippon Paper Industries) or glucose and 1.28% (w/v) diammonium hydrogen citrate in a 500 mL Erlenmeyer flask. The main culture was shaken at 220 rpm at 28 °C for 3–5 days. For sampling, cells were removed from the culture broth by centrifugation at 16,000g for 5 min, and the supernatant was filtered through a 0.20 μm cellulose acetate membrane filter (13CP020AN; Advantec, Toyo Roshi Kaisha). All experiments were carried out in triplicate.
Molecular cloning and construction of the expression cassettes
The genes of interest were amplified from the genomic DNA of T. reesei strain PC-3–7, and a vector fragment was amplified by inverse polymerase chain reaction (PCR) using pUC118 (Takara Bio) as the template. The amplified fragments, designed using primers that added a SwaI cleavage site, were ligated using an In-Fusion HD Cloning Kit (Clontech) according to the manufacturer’s protocol. Escherichia coli DH5a was used as a cloning host, and a NucleoSpin® Plasmid miniprep kit (Takara Bio) was used to purify the plasmid DNA. More details on the cloned gene and primers are provided in the Additional file, Table S5. The vector fragment pUC-K017 was generated by inverse PCR; it was derived from the ligated ace1 inserted plasmid (pUC-K003) and pyr4 marker cassette (pUC-K016). An inverse PCR fragment of the ace1 disruption construct (pUC-K017) and fragments of the act1 promoter, xyr1, and cbh1 terminator was ligated to generate the plasmid ΔAce1-Pact1-xyr1-pyr4 (pUC-K019). Using this plasmid as a template, inverse PCR was performed to mutate valine to phenylalanine at position 821 to obtain ΔAce1-Pact1-xyr1V821F-pyr4 (pUC-K020) and to mutate alanine to valine at position 824 to obtain ΔAce1-Pact1-xyr1A824V-pyr4 (pUC-K021). In the same manner, an inverse PCR fragment of the rce1 disruption construct (pUC-K018) and fragments of the act1 promoter, ORFs (crt1, bglr, vib1, ace2, PT-ace3, FL-ace3), and the cbh1 terminator were ligated to generate the plasmids pUC-K022, pUC-K023, pUC-K024, pUC-K025, pUC-K026, and pUC-K027, respectively. For PT-ace3 and FL-ace3, pUC-K010 was used as a template to design a forward primer based on the two types of putative initiation codons. More details on vector construction and the primers used are provided in the Additional file, Table S6.
Transformation of T. reesei
Plasmids were linearized with SwaI prior to the transformation of T. reesei, or the PCR product was transformed using a modified protoplast-PEG method64, in which 20 mg/mL of Yatalase (Takara Bio) was used as the protoplasting enzyme instead of Novozyme 234 (Novozymes Bagsværd, Denmark). The transformed protoplasts were plated on minimal transformation medium [2.0% (w/v) glucose, 18.27% (w/v) sorbitol, 0.5% (w/v) (NH4)2SO4, 0.2% (w/v) CaCl2, 0.06% (w/v) MgSO4, 0.21% (w/v) CsCl, and 0.1% (w/v) trace element solution in 100 mM KH2PO4 buffer (pH 5.5)] for the pyr4 marker. The trace element solution contained 500 mg FeSO4·7H2O, 200 mg CoCl2, 160 mg MnSO4·H2O, and 140 mg ZnSO4·7H2O in 100 mL of distilled water. After two weeks of incubation at 30 °C, candidate transformants were streaked twice on selective plates (each minimal transformation medium without sorbitol) for several days at 30 °C for single-colony isolation. Single colonies were then transferred to PDA plates for one week at 30 °C to allow for the formation of conidia. According to the manufacturer’s protocol, one transformant was confirmed by colony PCR using KOD One (Toyobo). To transform the resulting transformants again using the PDA medium containing 0.2% (w/v) 5-fluoroorotic acid (5-FOA) monohydrate, a strain that acquired 5-FOA resistance again (pyr4 pop-out through homologous recombination) was selected.
Culture supernatant and cell biomass analysis
According to the manufacturer’s protocol, protein concentration was determined using the Bradford protein assay (Bio-Rad) with bovine gamma globulin as the standard. The glucose concentration in the supernatant was quantified using the Glucose CII Test Wako Kit (Wako Chemicals). Specifically, 150 μL of the reaction solution was added to 1 μL of the diluted supernatants in a 96-well plate, mixed well, and incubated at room temperature for 15 min. The absorbance of all samples and standards was measured at 505 nm using a microplate reader (Molecular Devices).
Real-time quantitative PCR (RT-qPCR) analysis
The cell pellet at 48 h, collected by centrifugation, was lightly dewatered and frozen in liquid nitrogen. A metal cone was placed in the frozen sample prior to crushing with a Multi-Beads Shocker (Yasui Kikai Corp.) at 1700 rpm for 10 s, and RNA extraction was subsequently performed using the RNeasy Mini Kit (Qiagen), according to the manufacturer’s protocol. gDNA digestion and cDNA synthesis were performed using ezDNase™ Enzyme (Invitrogen) and SuperScript™ IV VILO™ Master Mix (Invitrogen), respectively. RT-qPCR experiments were performed with Brilliant III Ultra-Fast SYBR Green QPCR Master Mixes (Agilent), and the transcriptional levels were evaluated using the ΔΔCt method using pgk1 gene as a normalizer and E1AB1 (Fig. 3d,e) or E1AB1-X (Fig. 4a) strain as calibrator. All samples were analyzed in at least three independent biological experiments. The primers used for real-time PCR were designed using Primer3 (https://bioinfo.ut.ee/primer3-0.4.0/) and are listed in the Additional file Table S4.
Enzyme composition analysis
SDS-PAGE was carried out using Any kD Mini-PROTEAN TGX Precast Protein Gels (Bio-Rad) for 35 min at 200 V. The gel was activated for 5 min and imaged using the ChemiDoc MP imaging system (Bio-Rad). Precision Plus Protein Unstained Standard (5 μL; Bio-Rad) was used as a molecular mass marker. Unless otherwise noted, 2.5 μg of protein was loaded in each well. The gels were cropped in the 15–250 kDa range because no clear bands were detected under 15 kDa (the original gel of Figs. 1b, 2b, and 3b were presented in Fig. S4, S5, and S6 see Additional file). The molecular weight of the protein bands was estimated using Image Lab software (BiFio-Rad), and the protein bands were annotated using the positions corresponding to previously reported cellulases and xylanases53. Protein identification using nano LC–MS/MS systems was performed in Japan Proteomics Co. LTD.
Enzyme activity analysis
The enzymatic activities of cellobiohydrolase, β-glucosidase, xylanase, and β-xylosidase were measured using the substrates p-nitrophenyl-β-d-lactoside (pNPL), p-nitrophenyl-β-d-glucopyranoside (pNPG), p-nitrophenyl-β-xylobioside (pNPX2), and p-nitrophenyl-β-d-xylopyranoside (pNPX), respectively. The reactions were carried out in 50 mM sodium acetate at pH 5.0 and 50 °C for 10 min and terminated by adding one volume of 1 M Na2CO3. The released p-nitrophenol was quantified by measuring the absorbance at 420 nm. One unit of activity is defined as the amount of enzyme that produced 1 μmol of p-nitrophenol per minute at 50 °C. Cellulose saccharification was performed on a 1-mL scale in 9-mL glass screw-top bottles at a loading of 5% (w/v) microcrystalline cellulose (Avicel® PH-101, Sigma-Aldrich) in 100 mM sodium acetate buffer pH 5.0, using an enzyme loading of 2.0 mg protein/g cellulose. The protein concentration was determined as mentioned above. The reaction was performed at 50 °C under shaking at 150 rpm for 72 h. Samples obtained following saccharification were filtered (0.2 μm), and the glucose concentration was measured using an enzymatic assay and a Multifunction Biosensor BF-7 (Oji Scientific Instruments), according to the manufacturer’s protocol.
Statistical analysis
All experiments were performed with at least three independent samples. Error bars indicate the standard deviation (SD) of the mean of triplicates. Statistical significance was determined by the two-tailed unpaired Student’s t-test. Within each set of experiments, p < 0.05 was considered significant.
Data availability
The protein and nucleotide sequences used in this study can be referenced from Uniprot under the following accession IDs: ACE1_G0RCC6, RCE1_G0RBV8, XYR1_G0RLE8, CRT1_G0RGH7, BGLR_G0RVU2, VIB1_G0R8Z5, ACE2_G0RKV9, ACE3 (partially truncated)_G0RIA0, ACE3 (full-length)_A0A5C1J077.
Abbreviations
- BGL:
-
β-Glucosidase
- BXL:
-
β-Xylosidase
- CBH:
-
Cellobiohydrolase
- CCR:
-
Carbon catabolite repression
- EG:
-
Endoglucanase
- PCR:
-
Polymerase chain reaction
- pNPG:
-
p-Nitrophenyl-β-d-glucopyranoside
- pNPL:
-
p-Nitrophenyl-β-d-lactoside
- pNPX:
-
p-Nitrophenyl-β-d-xylopyranoside
- pNPX2:
-
p-Nitrophenyl-β-xylobiosid
- XYN:
-
Xylanase
References
de Paula, R. G. et al. Engineered microbial host selection for value-added bioproducts from lignocellulose. Biotechnol. Adv. 37, 107347 (2019).
Cristina, A. et al. Engineering of holocellulase in biomass-degrading fungi for sustainable biofuel production. J. Clean. Prod. 371, 133488 (2022).
Nevalainen, H. & Peterson, R. Making recombinant proteins in filamentous fungi- Are we expecting too much?. Front. Microbiol. 5, 1–10 (2014).
Cherry, J. R. & Fidantsef, A. L. Directed evolution of industrial enzymes: An update. Curr. Opin. Biotechnol. 14, 438–443 (2003).
Bischof, R. H., Ramoni, J. & Seiboth, B. Cellulases and beyond: The first 70 years of the enzyme producer Trichoderma reesei. Microb. Cell Fact. 15, 1–13 (2016).
Martinez, D. et al. Genome sequencing and analysis of the biomass-degrading fungus Trichoderma reesei (syn. Hypocrea jecorina). Nat. Biotechnol. 26, 553–560 (2008).
Gusakov, A. V. Alternatives to Trichoderma reesei in biofuel production. Trends Biotechnol. 29, 419–425 (2011).
Fonseca, L. M., Parreiras, L. S. & Murakami, M. T. Rational engineering of the Trichoderma reesei RUT-C30 strain into an industrially relevant platform for cellulase production. Biotechnol. Biofuels 13, 1–15 (2020).
Johnson, E. Integrated enzyme production lowers the cost of cellulosic ethanol. Biofuels Bioprod. Biorefining 10, 164–174 (2016).
Klein-Marcuschamer, D., Oleskowicz-Popiel, P., Simmons, B. A. & Blanch, H. W. The challenge of enzyme cost in the production of lignocellulosic biofuels. Biotechnol. Bioeng. 109, 1083–1087 (2012).
Adsul, M. et al. Designing a cellulolytic enzyme cocktail for the efficient and economical conversion of lignocellulosic biomass to biofuels. Enzyme Microb. Technol. 133, 109442 (2020).
Fischer, J., Schroeckh, V. & Brakhage, A. A. Awakening of fungal secondary metabolite gene clusters. in Gene Expression Systems in Fungi: Advancements and Applications. Fungal Biology (Schmoll, M., Dattenböck, C. eds.). 253–273 (2016)
Kubicek, C. P., Mikus, M., Schuster, A., Schmoll, M. & Seiboth, B. Metabolic engineering strategies for the improvement of cellulase production by Hypocrea jecorina. Biotechnol. Biofuels 2, 19 (2009).
Adnan, M., Ma, X., Olsson, S., Wang, J. & Liu, G. Promoter regulation and genetic engineering strategies for enhanced cellulase expression in Trichoderma reesei. Microbiol. Res. 259, 127011 (2022).
Shida, Y., Furukawa, T. & Ogasawara, W. Deciphering the molecular mechanisms behind cellulase production in trichoderma reesei, the hyper-cellulolytic filamentous fungus. Biosci. Biotechnol. Biochem. 80, 1712–1729 (2016).
Adnan, M. et al. Carbon catabolite repression in filamentous fungi. Int. J. Mol. Sci. 19, 1–23 (2018).
Ilmén, M., Thrane, C. & Penttilä, M. The glucose repressor genecre1 of Trichoderma: Isolation and expression of a full-length and a truncated mutant form. Mol. Gen. Genet. 251, 451–460 (1996).
Campos Antoniêto, A. C. et al. Trichoderma reesei CRE1-mediated carbon catabolite repression in response to sophorose through RNA sequencing analysis. Curr. Genomics 17, 119–131 (2015).
Han, L. et al. Redesigning transcription factor Cre1 for alleviating carbon catabolite repression in Trichoderma reesei. Synth. Syst. Biotechnol. 5, 230–235 (2020).
Mandels, M. & Reese, E. T. Induction of cellulase in fungi by cellobiose. J. Bacteriol. 79, 816–826 (1960).
Mandels, M., Parrish, F. W. & Reese, E. T. Sophorose as an inducer of cellulase in Trichoderma viride. J. Bacteriol. 83, 400–408 (1962).
Sternberg, D. & Mandels, G. R. Induction of cellulolytic enzymes in Trichoderma reesei by sophorose. J. Bacteriol. 139, 761–769 (1979).
Morikawa, Y., Ohashi, T., Mantani, O. & Okada, H. Cellulase induction by lactose in Trichoderma reesei PC-3-7. Appl. Microbiol. Biotechnol. 44, 106–111 (1995).
Cziferszky, A., Mach, R. L. & Kubicek, C. P. Phosphorylation positively regulates DNA binding of the carbon catabolite repressor Cre1 of Hypocrea jecorina (Trichoderma reesei). J. Biol. Chem. 277, 14688–14694 (2002).
Aro, N., Ilmén, M., Saloheimo, A. & Penttilä, M. ACEI of Trichoderma reesei is a repressor of cellulase and xylanase expression. Appl. Environ. Microbiol. 69, 56–65 (2003).
Cao, Y. et al. Rce1, a novel transcriptional repressor, regulates cellulase gene expression by antagonizing the transactivator Xyr1 in Trichoderma reesei. Mol. Microbiol. 105, 65–83 (2017).
Stricker, A. R., Grosstessner-Hain, K., Würleitner, E. & Mach, R. L. Xyr1 (Xylanase Regulator 1) regulates both the hydrolytic enzyme system and D-xylose metabolism in Hypocrea jecorina. Eukaryot. Cell 5, 2128–2137 (2006).
Mach-Aigner, A. R. et al. Transcriptional regulation of xyr1, encoding the main regulator of the xylanolytic and cellulolytic enzyme system in Hypocrea jecorina. Appl. Environ. Microbiol. 74, 6554–6562 (2008).
Lichius, A. et al. Genome sequencing of the Trichoderma reesei QM9136 mutant identifies a truncation of the transcriptional regulator XYR1 as the cause for its cellulase-negative phenotype. BMC Genomics 16, 1–20 (2015).
Zhang, X., Li, Y., Zhao, X. & Bai, F. Constitutive cellulase production from glucose using the recombinant Trichoderma reesei strain overexpressing an artificial transcription activator. Bioresour. Technol. 223, 317–322 (2017).
Derntl, C., MacH, R. L. & MacH-Aigner, A. R. Fusion transcription factors for strong, constitutive expression of cellulases and xylanases in Trichoderma reesei. Biotechnol. Biofuels 12, 1–18 (2019).
Derntl, C. et al. Mutation of the Xylanase regulator 1 causes a glucose blind hydrolase expressing phenotype in industrially used Trichoderma strains. Biotechnol. Biofuels 6, 1–11 (2013).
Ellilä, S. et al. Development of a low-cost cellulase production process using Trichoderma reesei for Brazilian biorefineries. Biotechnol. Biofuels 10, 1–17 (2017).
Aro, N., Saloheimo, A., Ilmén, M. & Penttilä, M. ACEII, a novel transcriptional activator involved in regulation of cellulase and xvlanase genes of Trichoderma reesei. J. Biol. Chem. 276, 24309–24314 (2001).
Häkkinen, M. et al. Screening of candidate regulators for cellulase and hemicellulase production in Trichoderma reesei and identification of a factor essential for cellulase production. Biotechnol. Biofuels 7, 1–21 (2014).
Ivanova, C. et al. Genome sequencing and transcriptome analysis of Trichoderma reesei QM9978 strain reveals a distal chromosome translocation to be responsible for loss of vib1 expression and loss of cellulase induction. Biotechnol. Biofuels 10, 1–15 (2017).
Ivanova, C., Bååth, J. A., Seiboth, B. & Kubicek, C. P. Systems analysis of lactose metabolism in Trichoderma reesei identifies a lactose permease that is essential for cellulase induction. PLoS ONE 8, 1–10 (2013).
Zhang, W. et al. Two major facilitator superfamily sugar transporters from Trichoderma reesei and their roles in induction of cellulase biosynthesis. J. Biol. Chem. 288, 32861–32872 (2013).
Nitta, M. et al. A new Zn(II) 2Cys 6-type transcription factor BglR regulates β-glucosidase expression in Trichoderma reesei. Fungal Genet. Biol. 49, 388–397 (2012).
Stricker, A. R., Trefflinger, P., Aro, N., Penttilä, M. & Mach, R. L. Role of Ace2 (Activator of Cellulases 2) within the xyn2 transcriptosome of Hypocrea jecorina. Fungal Genet. Biol. 45, 436–445 (2008).
Zhang, J. et al. The transcription factor ACE3 controls cellulase activities and lactose metabolism via two additional regulators in the fungus Trichoderma reesei. J. Biol. Chem. 294, 18435–18450 (2019).
Chen, Y. et al. Engineering of Trichoderma reesei for enhanced degradation of lignocellulosic biomass by truncation of the cellulase activator ACE3. Biotechnol. Biofuels 13, 1–14 (2020).
Luo, Y. et al. Modification of transcriptional factor ACE3 enhances protein production in Trichoderma reesei in the absence of cellulase gene inducer. Biotechnol. Biofuels 13, 1–16 (2020).
Zhang, F., Zhao, X. & Bai, F. Improvement of cellulase production in Trichoderma reesei Rut-C30 by overexpression of a novel regulatory gene Trvib-1. Bioresour. Technol. 247, 676–683 (2018).
Chen, X., Song, B., Liu, M., Qin, L. & Dong, Z. Understanding the role of Trichoderma reesei Vib1 in gene expression during cellulose degradation. J. Fungi 7, 613 (2021).
Havukainen, S., Valkonen, M., Koivuranta, K. & Landowski, C. P. Studies on sugar transporter CRT1 reveal new characteristics that are critical for cellulase induction in Trichoderma reesei. Biotechnol. Biofuels 13, 1–20 (2020).
Wang, Z. et al. Functional characterization of sugar transporter CRT1 reveals differential roles of its C-terminal region in sugar transport and cellulase induction in Trichoderma reesei. Microbiol. Spectr. 10, 872 (2022).
Kawamori, M., Morikawa, Y. & Takasawa, S. Induction and production of cellulases by l-sorbose in Trichoderma reesei. Appl. Microbiol. 24, 449–453 (1986).
Shida, Y. et al. The impact of a single-nucleotide mutation of bgl2 on cellulase induction in a Trichoderma reesei mutant. Biotechnol. Biofuels 8, 1–18 (2015).
De Oliveira Porciuncula, J. et al. Single nucleotide polymorphism analysis of a Trichoderma reesei hyper-cellulolytic mutant developed in Japan. Biosci. Biotechnol. Biochem. 77, 534–543 (2013).
Schmoll, M. & Schuster, A. Biology and biotechnology of Trichoderma. Appl. Microbiol. Biotechnol. 87, 787–799 (2010).
Baba, Y., Sumitani, J. I., Tani, S. & Kawaguchi, T. Characterization of Aspergillus aculeatus β-glucosidase 1 accelerating cellulose hydrolysis with Trichoderma cellulase system. AMB Exp. 5, 1–8 (2015).
Nakazawa, H. et al. A high performance Trichoderma reesei strain that reveals the importance of xylanase III in cellulosic biomass conversion. Enzyme Microb. Technol. 82, 89–95 (2016).
Shibata, N. et al. Disruption of alpha-tubulin releases carbon catabolite repression and enhances enzyme production in Trichoderma reesei even in the presence of glucose. Biotechnol. Biofuels 14, 1–16 (2021).
Zevenhuizen, L. P. T. M. & Bartnicki-Garcia, S. Structure and role of a soluble cytoplasmic glucan from Phytophthora cinnamomi. J. Gen. Microbiol. 61, 183–188 (1970).
Chen, Y. et al. Trichoderma reesei ACE4, a novel transcriptional activator involved in the regulation of cellulase genes during growth on cellulose. Appl. Environ. Microbiol. 87, 1–16 (2021).
Zheng, F. et al. Engineering Trichoderma reesei for hyperproduction of cellulases on glucose to efficiently saccharify pretreated corncobs. J. Agric. Food Chem. 68, 12671–12682 (2020).
Hong, M. et al. Structural basis for dimerization in DNA recognition by Gal4. Structure 16, 1019–1026 (2008).
Watson, T. G., Nelligan, I. & Lessing, L. Cellulase production by Trichoderma reesei (RUT-C30) in fed-batch culture. Biotechnol. Lett. 6, 667–672 (1984).
Jourdier, E. et al. Cellulase activity mapping of Trichoderma reesei cultivated in sugar mixtures under fed-batch conditions. Biotechnol. Biofuels 6, 1–12 (2013).
Nevalainen, H. & Peterson, R. Heterologous expression of proteins in Trichoderma. in New and Future Developments in Microbial Biotechnology and Bioengineering: Aspergillus System Properties and Applications. 89–102 (2016)
Rantasalo, A. et al. Novel genetic tools that enable highly pure protein production in Trichoderma reesei. Sci. Rep. 9, 1–12 (2019).
Zhang, J., Wu, C., Wang, W., Wang, W. & Wei, D. A versatile Trichoderma reesei expression system for the production of heterologous proteins. Biotechnol. Lett. 40, 965–972 (2018).
Penttilä, M., Nevalainen, H., Rättö, M., Salminen, E. & Knowles, J. A versatile transformation system for the cellulolytic filamentous fungus Trichoderma reesei. Gene 61, 155–164 (1987).
Acknowledgements
The authors thank Prof. Wataru Ogasawara from Nagaoka University of Technology for providing the T. reesei E1AB1 strain and Prof. Ishii from Kobe University for deepening our consideration by discussing this study. We would like to thank Editage (www.editage.com) for English language editing.
Author information
Authors and Affiliations
Contributions
T.A., S.I., and H.Ka. designed the study; T.A. analyzed the results and drafted the manuscript; S.I. participated in the construction of strains and gene analysis; H.Ka. revised the manuscript; N.S., H.Ka., H.Ko., K.I., and Y.T. reviewed and commented on the manuscript. All the authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Arai, T., Ichinose, S., Shibata, N. et al. Inducer-free cellulase production system based on the constitutive expression of mutated XYR1 and ACE3 in the industrial fungus Trichoderma reesei. Sci Rep 12, 19445 (2022). https://doi.org/10.1038/s41598-022-23815-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-022-23815-4
- Springer Nature Limited