Abstract
Modern cone-beam CT systems are capable of ultra-high-resolution 3D imaging in addition to conventional radiography and fluoroscopy. The combination of various imaging functions in a multi-use setup is particularly appealing for musculoskeletal interventions, such as CBCT arthrography (CBCTA). With this study, we aimed to investigate the feasibility of CBCTA of the wrist in a “one-stop-shop” approach with a gantry-free twin robotic scanner that does not require repositioning of subjects. Additionally, the image quality of CBCTA was compared to subsequent arthrograms on a high-end multidetector CT (MDCTA). Fourteen cadaveric wrists received CBCTA with four acquisition protocols. Specimens were then transferred to the CT suite for additional MDCTA. Dose indices ranged between 14.3 mGy (120 kVp/100 effective mAs; full-dose) and 1.0 mGy (70 kVp/41 effective mAs; ultra-low-dose) for MDCTA and between 17.4 mGy (80 kVp/2.5 mAs per pulse; full-dose) and 1.2 mGy (60 kVp/0.5 mAs per pulse; ultra-low-dose) for CBCTA. Subjective image quality assessment for bone, cartilage and ligamentous tissue was performed by seven radiologists. The interrater reliability was assessed by calculation of the intraclass correlation coefficient (ICC) based on a two-way random effects model. Overall image quality of most CBCTA was deemed suitable for diagnostic use in contrast to a considerable amount of non-diagnostic MDCTA examinations (38.8%). The depiction of bone, cartilage and ligaments in MDCTA with any form of dose reduction was inferior to any CBCTA scan with at least 0.6 mAs per pulse (all p < 0.001). Full-dose MDCTA and low-dose CBCTA were of equal quality for bone tissue visualization (p = 0.326), whereas CBCTA allowed for better depiction of ligaments and cartilage (both p < 0.001), despite merely one third of radiation exposure (MDCTA–14.3 mGy vs. CBCTA–4.5 mGy). Moderate to good interrater reliability was ascertained for the assessment all tissues (ICC 0.689–0.756). Overall median examination time for CBCTA was 5.4 min (4.8–7.2 min). This work demonstrates that substantial dose reduction can be achieved in CT arthrography of the wrist while maintaining diagnostic image quality by employing the cone-beam CT mode of a twin robotic X-ray system. The ability of the multi-use X-ray system to switch between fluoroscopy mode and 3D imaging allows for “one-stop-shop” CBCTA in minimal examination time without the need for repositioning.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
While wrist pain represents a common medical condition1, causes can range from fractures to cartilage injuries to discontinuity of ligamentous structures. Lesions of the intrinsic carpal ligaments and the triangular fibrocartilage complex (TFCC) are often concomitant findings in both traumatic or degenerative conditions of the wrist. Tears of the scapholunate ligament are present in 10% of distal radius fractures2, while injuries of the lunotriquetral ligament are more infrequent3,4. Lesions of these fine stabilizers correspond with changes in the biomechanics of the wrist and eventually invoke osteoarthritis and chronic pain5,6. While degenerative lesions of the TFCC are usually asymptomatic, traumatic injuries commonly result in ulnar-sided wrist pain7. Due to overlapping symptoms and the complex anatomy of the wrist, identifying subtle soft tissue injuries remains a challenging task in clinical examinations of patients with wrist fractures. Furthermore, neither first-line radiography nor standard unenhanced CT are capable of directly visualizing ligamentous or cartilaginous lesions, albeit the latter provides viable information on fracture morphology and fragment displacement8. To prevent late complications like carpal instability, however, more sophisticated imaging techniques can be required with certain fracture patterns. Plain and contrast-enhanced MRI occasionally struggle with discreet lesions like isolated ruptures of the foveal attachment of the TFCC, which represents the main stabilizer of the DRUJ9, or chondral lesions of small articular surfaces10,11,12. Hence, regardless of drawbacks such as lengthy examinations and uncomfortable positioning13,14,15, MR arthrography is often regarded as the method of choice for imaging the intrinsic ligaments and the TFCC16,17,18. However, previous studies have reported comparable sensitivity and specificity levels for CT arthrography18,19,20. While multidetector CT arthrography (MDCTA) represents the most common approach to this technique, the emergence of dedicated extremity scanners with flat-panel detectors and cone-shaped beam geometry has opened up a new option in the form of cone-beam CT arthrography (CBCTA)21. Superior results have already been reported for plain CBCT in comparison to MDCT of the appendicular skeleton22. More importantly, though, new types of scanner architecture, such as the twin robotic design of the X-ray system employed in this study, offer a wider range of functionality, e.g. by combining fluoroscopy with ultra-high-resolution 3D imaging in the same position.
Due to the current lack of data on that topic, this experimental study was performed to investigate the feasibility of “one-stop-shop” CBCTA in cadaveric specimens. Using various scan protocols to define the best possible trade-off between image quality and radiation dose, we hypothesized that CBCTA would provide low examination times while yielding superior ratings over standard MDCTA in a multi-observer analysis.
Material and methods
Cadaveric phantoms
Eight formalin-fixed cadaveric specimens were provided by the anatomical institute of the local university. The body donors had provided written informed consent to donate their remains posthumously for study and research purposes. All experimental protocols were approved and further informed consent was waived by the Institutional Review Board of the University of Würzburg, Germany (protocol number: 2020050601). Additional written informed consent was waived by the ethics committee. Figure 1 illustrates the study design. Of the total of 16 wrists available, two wrists had to be excluded from the study due to implanted osteosynthesis material in the distal radius. Therefore, the final study sample consisted of 14 cadaveric wrists. The datasets generated and/or analysed during the current study are not publicly available but are available from the corresponding author on reasonable request. Due to the nature of this research, participants of this study did not agree for their data to be shared in a public repository. All methods were carried out in accordance with relevant guidelines and regulations.
Arthrography
Each arthrography was performed by a board-certified radiologist with 7 years of experience in musculoskeletal imaging employing the fluoroscopy mode of the multi-use X-ray system (Multitom Rax, Siemens Healthineers, Erlangen, Germany) for guidance. Specimens were brought in a supine position with the respective arm abducted by approximately 90 degrees (Fig. 2). For the procedure of articular contrast injection, the acquisition of fluoroscopy images was controlled by the scanner’s multifunctional footswitch. A 25 gauge needle (BD Eclipse™ Smartslip, Becton, Dickinson and Company, Franklin Lakes, New Jersey, United States of America) was utilized to puncture the articular capsule. To mimic the examination of real-world patients, a mixture of iodine contrast medium with a concentration of 300 mg per ml (Imeron 300®, Bracco S.p.A., Milan, Italy) and anaesthetic with a concentration of 10 mg per ml (Mecain®, Puren Pharma GmbH & Co. KG, Munich, Germany) was injected. For assessment of the intrinsic carpal ligaments, the midcarpal joint was punctured first between the lunate, triquetral, capitate and hamate bone, followed by the radiocarpal joint adjacent to the proximal scaphoid pole. Injected volumes ranged between 2–4 ml (midcarpal joint) and 1.5–3 ml (radiocarpal joint).
Scanner and scan protocols
After completing the arthrography procedure, all CBCT scans were acquired without further delay and without repositioning of the cadaveric specimens. The gantry-free multifunctional X-ray system consists of two ceiling rails with mounted robotic arms, which simultaneously and synchronously navigate a quadratic flat-panel detector and the X-ray tube in an asymmetric source-to-image distance (1150 mm) and a sweep angle of 200° around the isocenter in the 3D CBCT mode. The resulting total scan time is 14 s. With the current software version VF11 (Siemens Healthineers), the unbinned readout of the detector in ultra-high-resolution mode results in a 1440 × 1440 matrix of pixels with an effective size of 149 μm.
The four CBCT scan protocols comprised of tube voltages between 60 and 80 kVp and current–time products between 0.5 and 2.5 mAs. The scanner-immanent prefiltration was 0.3 mm of copper. Time intervals were recorded for each step of the arthrogram and 3D imaging process. After completing all CBCT scans, the specimens were immediately transferred to a high-end, gantry-based MDCT scanner (Somatom Force, Siemens Healthineers) and brought in prone position with the wrist elevated above the head (“superman” position). The four MDCT scan protocols varied between 70 and 120 kVp tube voltage and 25–398 mAs current–time product. One MDCT protocol employed tin prefiltration (0.6 mm).
In total, eight different scan protocols were defined for the purpose of this study. The individual detailed combinations are summarized in Table 1. The radiation dose in MDCT scans was determined according to the dose-length product and the volume CT dose indices for a 16 cm phantom (CDTIvol). For comparison, CTDIvol equivalents were calculated for all CBCT scans by multiplying dose-area-products by a linear scaling factor that was evaluated in advance for each scan protocol. Dose-length-product measurements were based on a conventional polymethylmethacrylate dosimetry phantom (IEC 60601-2-44:2009) with a diameter of 16 cm. Standard weighting factors were applied to obtain volume dose-length-products, which then were divided by the field of view in z-axis, i.e. by the beam width. The volume computed tomography dose indices were then divided by the dose-area-products of the automatic dose report, resulting in the required scaling factor.
Image reconstruction parameters
Based on the clinical standard procedure for post-processing, all scanner-side raw data image reconstructions were performed with a high-resolution bone kernel (Ur77; Siemens Healthineers). Multiplanar reconstructions in axial, coronal and sagittal planes were conducted for all scans utilizing a dedicated 3D processing software (syngo.via View&GO and syngo.via, both Siemens Healthineers) in 1.0 mm slice thickness with an increment of 0.5 mm, a field of view of 80 mm, and an image matrix of 1024 × 1024 pixels. For identical image presentation, reconstruction processes were identical for each scanner type and scan protocol. Basic values for window width and level were selected at 3000 and 1000 Hounsfield units (HU) for optimal bone tissue depiction. However, observers were permitted to modify window settings at will for reading.
Image evaluation
Images were evaluated by seven radiologists independently on a certified diagnostic monitor (RadiForce RX660, EIZO, Hakusan, Japan) with a standard picture archiving and communication software (Merlin, Phönix-PACS, Freiburg, Germany). The radiologists’ level of experience in musculoskeletal imaging ranged between two and eight years. Without having been provided any further information regarding image acquisition, readers were first tasked to evaluate whether images were suitable for diagnostic use. Subsequently, the observers were requested to individually rate the image quality for bone, cartilage and the intrinsic ligaments using a seven-point scale (1 = very poor; 2 = poor; 3 = fair; 4 = satisfactory; 5 = good; 6 = very good; 7 = excellent). Image noise was measured in normed regions of interest to assess image quality quantitatively.
Statistical analysis
Statistical software (SPSS, IBM, Armonk, USA) was employed for all analyses. Kolmogorov–Smirnov tests were performed to assess normal distribution in cardinal variables. Ordinal variables are presented as absolute and relative frequencies with median values and interquartile ranges (IQR, 25–75%). Friedman tests and Bonferroni-corrected pairwise post-hoc analyses were conducted to compare the mean rank distribution in paired non-parametric variables. Null hypotheses were rejected and statistical significance assumed if computed p values were ≤ 0.05. To test for interrater agreement, the intraclass correlation coefficient (ICC) was calculated for absolute agreement of single measures in a two-way random effects model. ICC scores were interpreted following Koo and Li: < 0.50: poor; 0.50–0.75: moderate; 0.75–0.90: good; > 0.90: excellent reliability23.
Results
Depending on the acquisition parameters of the respective 3D scan protocol, CTDIvol in this study ranged between 1.0 and 17.4 mGy (Table 1). The overall image quality of most CBCT arthrograms was considered suitable for use in clinical routine (386/392 ratings, 98.5% examinations in diagnostic quality), whereas one third of MDCTA scans was deemed insufficient for patient imaging (244/392, 62.2% examinations in diagnostic quality). Detailed subjective image quality ratings are summarized in Table 2. The best image quality in each category was achieved with the full-dose CBCTA protocol (80 kVp, 2.5 mAs per pulse), which also induced the highest radiation dose (17.4 mGy) (Fig. 3). While no difference was ascertained between full-dose MDCTA (120 kVp, 100 mAs) and low-dose CBCTA (80 kVp, 0.6 mAs) for bone tissue visualization (p = 0.326), CBCTA scans allowed for better depiction of ligaments and cartilage (both p < 0.001), despite being associated with just one third of radiation exposure (MDCTA—14.3 mGy vs. CBCTA—4.5 mGy). Figure 4 illustrates the superior image quality of CBCTA in a cadaveric specimen with scapholunate ligament tear. Irrespective of the tissue assessed, no significant difference was recorded between CBCTA scans with 80 kVp/0.6 mAs and 60 kVp/2.5 mAs (all p ≥ 0.618), although the latter protocol resulted in twice the radiation dose (80 kVp–4.5 mGy vs. 60 kVp–9.5 mGy). Tin-filtered MDCTA with 100 kVp were considered equal to low-dose MDCTA studies with reduced tube current or potential (all p ≥ 0.204). Notably, however, all MDCTA protocols with any form of dose reduction were deemed inferior to CBCTA scans with at least 0.6 mAs per pulse (bone/cartilage/ligaments: all p < 0.001). Between ultra-low-dose examinations, CBCTA with 60 kVp/0.5 mAs were rated better than MDCTA with 70 kVp/41 mAs for each of the three categories (all p < 0.001). The superior visualization of bone microarchitecture and alterations thereof in CBCTA is exemplified in Fig. 5. Detailed results of pairwise comparison between the scan protocols on either scanner are shown in Table 3. Interrater reliability was moderate—good for bone tissue (ICC 0.690 [95% confidence interval 0.555–0.787; p < 0.001]), cartilage (0.756 [0.672–0.823; p < 0.001]) and ligament assessment (0.689 [0.586–0.772; p < 0.001]). Image noise was lowest and highest in CBCTA scans with 80 kVp/2.5 mAs and 60 kVp/0.5 mAs, respectively. For MDCTA, lowest and highest noise was measured in examinations with 120 kVp/100 mAs and 70 kVp/41 mAs. Detailed noise levels are presented in Table 4.
Coronal view of various scan protocols (in descending order of radiation dose) depicts a scapholunate ligament tear. Visualization of the tear’s location in the scaphoid portion of the ligament is superior in cone-beam CT scan (CBCT; upper row). Despite being acquired 30 minutes later, the blurriness of multidetector CT images (MDCT; lower row) partially offsets the advantage of increased articular distension for cartilage assessment, for example in the radiocarpal compartment.
Axial views of the same cadaveric specimen depict the torn dorsal portion of the scapholunate ligament, which functions as the primary stabilizer of the proximal carpal row. While increased articular distension over time was helpful for ligament analysis in multidetector CT (MDCT; lower row), the detailed visualization of bone microarchitecture in cone-beam CT (CBCT; upper row) allowed for superior depiction of a ganglion cyst within the lunate bone.
The median time required for the fluoroscopy-guided two-compartment wrist arthrography was 2.8 min (IQR 2.0–5.0 min). Irrespective of scan protocol, the median time interval between the final contrast injection (into the radiocarpal joint) and completion of the automated scanner-side image reconstruction in orthogonal planes was 2.4 min (IQR 2.2–2.4 min). Time requirements for each step of gantry-free CBCTA are summarized in Table 5.
Discussion
In this experimental study, we demonstrated the feasibility of combining fluoroscopy-guided wrist arthrography and ultra-high-resolution CBCT in a “one-stop-shop” approach using a multipurpose, twin robotic X-ray system. Comparing the image quality with various dose levels to the performance of a high-end MDCT scanner, our findings suggest significant dose reduction potential for ultra-high-resolution CBCTA. Particularly, the considerable amount of non-diagnostic MDCTA examinations has to be mentioned when any form of dose reduction was employed. In contrast, any CBCTA protocol with at least 0.6 mAs per pulse provided diagnostic image quality in every scan. One of the major drawbacks of CT arthrography in comparison to MR arthrography, i.e. the radiation exposure, can thus be minimized. The findings in this study correlate with a recent meta-analysis by Nardi et al. for plain CBCT, which demonstrated significant dose reduction potential in comparison to MDCT for imaging tasks concerning the appendicular skeleton24. The sustained subjective and quantitative image quality in ultra-low-dose CBCTA may be mostly interrelated with the superior spatial resolution, which is derived from the combination of an asymmetric acquisition geometry and unbinned readout of the flat-panel detector with an isotropic pixel size of 149 µm. For comparison, the employed MDCT systems’ ultra-high-resolution scan mode allows for 300 µm in the axial plane and 400 µm in z-direction (with a gantry rotation time of 1 s).
In literature, the diagnostic value of wrist MDCTA is described to be equivalent or even better than MRI or MR arthrography for lesions of the cartilage, intrinsic carpal ligaments and TFCC18,20. Especially in small joints with thin hyaline cartilage, MRI, which is often seen as the imaging technique of choice in clinical settings, struggles regarding resolution and depiction of discreet chondral injuries11,25,26. Although the sensitivity and specificity for these lesions could be improved by direct MR arthrography up to 84–96%11,27, CBCTA of the wrist should be considered as an alternative imaging technique with higher spatial resolution and significantly shorter acquisition time. This combination may be beneficial not only for patients with contraindications for MRI but also for patients unable to maintain the required scan position (“superman” position) over a longer time. In addition, CT arthrography is advantageous regarding detailed evaluation of the subchondral surface in case of cystic or sclerotic alterations, while MR arthrography maintains the advantage of superior assessment of bone marrow abnormalities10,28.
Finally, the gantry-free cone-beam CT with two robotic arms used in this study allows for a “one-stop-shop” approach to wrist arthrography with a median time interval of 2.4 min between the final contrast injection and completion of the scanner-side image reconstruction in orthogonal planes. This is possible because patient repositioning or even relocation between fluoroscopy and CT suite is not necessary. The subject remains in a comfortable scan position with the arm abducted at 90°, eliminating delays and reducing logistical challenges. Although studies have reported that a significant amount of contrast medium remains in the joint space for up to 120 min in delayed CT arthrography29, a short time interval between injection and imaging is recommended to receive optimal contrast conditions. Further studies are required to analyze the impact of the time aspect in clinical settings.
Limitations
Regarding this study, several limitations are to be mentioned. Receiving the specimens without further information on body donor age, time of fixation and bone density, preexisting osteopenia, as well as the bone demineralization in formalin could have a negative influence on the subjective image analysis30,31. Also, acquiring the MDCTA scans in a median time interval of 30 min after injection may have led to accumulation of intraarticular contrast volume in comparison to CBCTA examinations, resulting in superior joint distension. Also, by examining cadaveric wrists, the impact of potential motion artefacts and off-center positioning with an overall scan time of 12 s in CBCT were not evaluated, each of which could conceivably impair the image quality regardless of the benefits of comfortable table-side positioning. As MDCT systems generally require shorter scan times18, it remains unclear whether the comfortable stance offsets the disadvantages inherent to longer scan times in CBCT. At last, despite being blinded to image acquisition parameters, the observers may have become more acquainted with imaging characteristics throughout their reading sessions.
Conclusion
With its twin robotic arms, the multi-use X-ray system enables fluoroscopy-guided wrist arthrography and subsequent ultra-high-resolution cone-beam CT in a “one-stop-shop” approach without subject repositioning. In addition to time savings, the combined procedure of cone-beam CT arthrography provides superior image quality compared to standard MDCT arthrograms and holds potential for significant radiation dose reduction.
Data availability
The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.
Abbreviations
- CBCTA:
-
Cone-beam computed tomography arthrography
- CTDIvol :
-
Volume computed tomography dose index (for 16 cm phantom)
- MDCTA:
-
Multidetector computed tomography arthrography
- TFCC:
-
Triangular fibrocartilage complex
References
Watanabe, A., Souza, F., Vezeridis, P. S., Blazar, P. & Yoshioka, H. Ulnar-sided wrist pain. II. Clinical imaging and treatment. Skelet. Radiol. 39, 837–857. https://doi.org/10.1007/s00256-009-0842-3 (2010).
Klempka, A. et al. Injuries of the scapholunate and lunotriquetral ligaments as well as the TFCC in intra-articular distal radius fractures. Prevalence assessed with MDCT arthrography. Eur. Radiol. 26, 722–732. https://doi.org/10.1007/s00330-015-3871-4 (2016).
Wagner, E. R., Elhassan, B. T. & Rizzo, M. Diagnosis and treatment of chronic lunotriquetral ligament injuries. Hand Clin. 31, 477–486. https://doi.org/10.1016/j.hcl.2015.04.006 (2015).
van de Grift, T. C. & Ritt, M. J. Management of lunotriquetral instability: A review of the literature. J. Hand Surg. Eur. 41, 72–85. https://doi.org/10.1177/1753193415595167 (2016).
Watson, H. K., Weinzweig, J. & Zeppieri, J. The natural progression of scaphoid instability. Hand Clin. 13, 39–49 (1997).
Rajan, P. V. & Day, C. S. Scapholunate interosseous ligament anatomy and biomechanics. J. Hand Surg. Am. 40, 1692–1702. https://doi.org/10.1016/j.jhsa.2015.03.032 (2015).
Oneson, S. R., Scales, L. M., Timins, M. E., Erickson, S. J. & Chamoy, L. MR imaging interpretation of the Palmer classification of triangular fibrocartilage complex lesions. Radiographics 16, 97–106. https://doi.org/10.1148/radiographics.16.1.97 (1996).
Grunz, J. P., Gietzen, C. H., Grunz, K., Bley, T. & Schmitt, R. Imaging of carpal instabilities. Rofo 193, 139–150. https://doi.org/10.1055/a-1219-8158 (2021).
Luetkens, K. S. et al. Contrast-enhanced MRI of the wrist: Intravenous application of gadolinium improves diagnosis in ulnar-sided injuries of the TFCC. Eur. J. Radiol. 143, 109901. https://doi.org/10.1016/j.ejrad.2021.109901 (2021).
Saupe, N. et al. MR imaging of cartilage in cadaveric wrists: Comparison between imaging at 1.5 and 3.0 T and gross pathologic inspection. Radiology 243, 180–187. https://doi.org/10.1148/radiol.2431060294 (2007).
Moser, T., Dosch, J. C., Moussaoui, A. & Dietemann, J. L. Wrist ligament tears: Evaluation of MRI and combined MDCT and MR arthrography. Am. J. Roentgenol. 188, 1278–1286. https://doi.org/10.2214/AJR.06.0288 (2007).
Zanetti, M., Saupe, N. & Nagy, L. Role of MR imaging in chronic wrist pain. Eur. Radiol. 17, 927–938. https://doi.org/10.1007/s00330-006-0365-4 (2007).
Maizlin, Z. V. et al. MR arthrography of the wrist: Controversies and concepts. Hand (N. Y.) 4, 66–73. https://doi.org/10.1007/s11552-008-9149-4 (2009).
Zanetti, M., Bram, J. & Hodler, J. Triangular fibrocartilage and intercarpal ligaments of the wrist: Does MR arthrography improve standard MRI? J. Magn. Reson. Imaging 7, 590–594. https://doi.org/10.1002/jmri.1880070322 (1997).
Theumann, N. H. et al. Ligamentous and tendinous anatomy of the intermetacarpal and common carpometacarpal joints: Evaluation with MR imaging and MR arthrography. J. Comput. Assist. Tomogr. 26, 145–152. https://doi.org/10.1097/00004728-200201000-00026 (2002).
Steinbach, L. S., Palmer, W. E. & Schweitzer, M. E. Special focus session. MR arthrography. Radiographics 22, 1223–1246. https://doi.org/10.1148/radiographics.22.5.g02se301223 (2002).
Carrino, J. A., Smith, D. K. & Schweitzer, M. E. MR Arthrography of the elbow and wrist. Semin. Musculoskelet. Radiol. 2, 397–414. https://doi.org/10.1055/s-2008-1080120 (1998).
Theumann, N., Favarger, N., Schnyder, P. & Meuli, R. Wrist ligament injuries: Value of post-arthrography computed tomography. Skelet. Radiol. 30, 88–93. https://doi.org/10.1007/s002560000302 (2001).
Khoury, V., Harris, P. G. & Cardinal, E. Cross-sectional imaging of internal derangement of the wrist with arthroscopic correlation. Semin. Musculoskelet. Radiol. 11, 36–47. https://doi.org/10.1055/s-2007-984417 (2007).
Schmid, M. R. et al. Interosseous ligament tears of the wrist: Comparison of multi-detector row CT arthrography and MR imaging. Radiology 237, 1008–1013. https://doi.org/10.1148/radiol.2373041450 (2005).
Ramdhian-Wihlm, R. et al. Cone-beam computed tomography arthrography: An innovative modality for the evaluation of wrist ligament and cartilage injuries. Skelet. Radiol. 41, 963–969. https://doi.org/10.1007/s00256-011-1305-1 (2012).
Luetkens, K. S. et al. Dose reduction potential in cone-beam CT imaging of upper extremity joints with a twin robotic X-ray system. Sci. Rep. 11, 20176. https://doi.org/10.1038/s41598-021-99748-1 (2021).
Koo, T. K. & Li, M. Y. A guideline of selecting and reporting intraclass correlation coefficients for reliability research. J. Chiropr. Med. 15, 155–163. https://doi.org/10.1016/j.jcm.2016.02.012 (2016).
Nardi, C. et al. Radiation dose in non-dental cone beam CT applications: A systematic review. Radiol. Med. 123, 765–777. https://doi.org/10.1007/s11547-018-0910-7 (2018).
Saupe, N. et al. MR imaging of the wrist: Comparison between 1.5- and 3-T MR imaging–preliminary experience. Radiology 234, 256–264. https://doi.org/10.1148/radiol.2341031596 (2005).
Haims, A. H. et al. MRI in the diagnosis of cartilage injury in the wrist. Am. J. Roentgenol. 182, 1267–1270. https://doi.org/10.2214/ajr.182.5.1821267 (2004).
Schmitt, R. et al. Direct MR arthrography of the wrist in comparison with arthroscopy: A prospective study on 125 patients. Rofo 175, 911–919. https://doi.org/10.1055/s-2003-40434 (2003).
Alam, F., Schweitzer, M. E., Li, X. X., Malat, J. & Hussain, S. M. Frequency and spectrum of abnormalities in the bone marrow of the wrist: MR imaging findings. Skelet. Radiol. 28, 312–317. https://doi.org/10.1007/s002560050523 (1999).
Kokkonen, H. T. et al. Delayed computed tomography arthrography of human knee cartilage in vivo. Cartilage 3, 334–341. https://doi.org/10.1177/1947603512447300 (2012).
Burkhart, K. J. et al. Influence of formalin fixation on the biomechanical properties of human diaphyseal bone. Biomed. Tech. (Berl.) 55, 361–365. https://doi.org/10.1515/BMT.2010.043 (2010).
Fonseca, A. A., Cherubini, K., Veeck, E. B., Ladeira, R. S. & Carapeto, L. P. Effect of 10% formalin on radiographic optical density of bone specimens. Dentomaxillofac. Radiol. 37, 137–141. https://doi.org/10.1259/dmfr/18109064 (2008).
Acknowledgements
The authors wish to thank the individuals who donated their body for research and educational purposes.
Disclaimer
Siemens Multitom Rax VF11 is not available in all countries due to regulatory reasons. Availability in the future cannot be guaranteed.
Funding
Open Access funding enabled and organized by Projekt DEAL. The funding was provided by Interdisziplinäres Zentrum für Klinische Forschung, Universitätsklinikum Würzburg (Z-2/CSP-06, Z-02/CSP-18) and also by Siemens Healthineers.
Author information
Authors and Affiliations
Contributions
K.S.L. analyzed all data and prepared the manuscript. Observer analysis was performed by K.S.L., J.P.G., H.H., N.C., T.S.P., P.G. and A.S.K., N.C. and H.H. supported preparation of the manuscript and figures. J.P.G. performed statistical analysis and revised the manuscript. T.A.B. and M.M.P. contributed to preparation of the manuscript and provided quality control. S.E. prepared the cadaveric specimen. A.S.K. designed and supervised the study. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
JPG [Grant Number Z-2/CSP-06] and PG [Grant Number Z-2/CSP-18] were funded by the Interdisciplinary Center of Clinical Research Würzburg, Germany. JPG and TAB serve as research consultants for Siemens Healthineers. The Department of Diagnostic and Interventional Radiology receives research funding by Siemens Healthineers. The authors of this manuscript declare no further relationships with any companies, whose products or services may be related to the subject matter of the article.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Luetkens, K.S., Grunz, JP., Paul, M.M. et al. One-stop-shop CT arthrography of the wrist without subject repositioning by means of gantry-free cone-beam CT. Sci Rep 12, 14422 (2022). https://doi.org/10.1038/s41598-022-18395-2
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-022-18395-2
- Springer Nature Limited