Abstract
Immersion optics enable creation of systems with improved optical concentration and coupling by taking advantage of the fact that the luminance of light is proportional to the square of the refractive index in a lossless optical system. Immersion graded index optical concentrators, that do not need to track the source, are described in terms of theory, simulations, and experiments. We introduce a generalized design guide equation which follows the Pareto function and can be used to create various immersion graded index optics depending on the application requirements of concentration, refractive index, height, and efficiency. We present glass and polymer fabrication techniques for creating broadband transparent graded index materials with large refractive index ranges, (refractive index ratio)2 of ~2, going many fold beyond what is seen in nature or the optics industry. The prototypes demonstrate 3x optical concentration with over 90% efficiency. We report via functional prototypes that graded-index-lens concentrators perform close to the theoretical maximum limit and we introduce simple, inexpensive, design-flexible, and scalable fabrication techniques for their implementation.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
Harnessing the plentiful solar energy reaching the earth via photovoltaics will play a major role in satisfying our future energy needs in a sustainable way. One promising approach is concentrated photovoltaics1, and several ways to achieve concentration are being used in the field2,3- Fresnel lenses4,5, mirrors6,7, parabolic concentrators8,9, secondary high-index optics10, waveguides11,12,13, immersion lenses14, surface nanotexturing15. The majority of these require active tracking of the Sun as they have to face the light source within a few degrees. Some of the above are passive concentrators, i.e., do not need to track the Sun, however they still offer modest acceptance angles that do not span the available 2π steradians. We present a passive concentrator device, AGILE (Axially Graded Index LEns)16. Henceforth, this immersion graded index optical concentrator is written as AGILE in the manuscript. AGILE does not need solar tracking and follows the cosine projection maximum limit, concentrating light incident on it from all angles.
The AGILE allows for non-pointing (i.e., removing the need to track the Sun) concentration systems which reduce the amount of photovoltaic (PV) material required but also efficiently absorb diffuse light. Light scattering is present due to cloud cover and atmosphere; and diffuse light can be as high as 20% even on a sunny day17. Figure 1a depicts how light is concentrated in the AGILE concentrator. Light rays incident from the entire 2π steradians enter the larger aperture with refractive index (RI) of 1, curve towards the normal via refraction along the height of the cone in the axial gradient RI, reflect from the sidewalls, and reach the smaller output aperture with high RI, e.g., silicon with RI ~ 3.5, without need to track the light source. Figure 1c portrays the AGILE concentrator array system, made up of the repeated unit shown in Fig. 1b, that absorbs all the incident light and hence appears dark. Video clip of the AGILE array system is attached in the supplementary material. In this video, the AGILE does not have metallic reflective sidewalls so that the graded index material can be visualised. AGILE allows near perfect antireflection and coupling, encapsulation, space for circuitry and cooling, and conformal design. These immersion graded index optics can also realize applications in areas like light management in solid state lighting, laser couplers, display technology etc.
a Depiction of the optical concentration action, b repeating unit of AGILE, c concentrator arrays with built-in anti-reflection and encapsulation, no need for tracking the source, and spatially separated PV cells which have advantages of reduced PV material use, hence lower cost with space for cooling and circuitry.
Comparison of different concentrator designs
Ray tracing simulations were performed with the software FRED. We performed simulations to compare optical concentration efficiencies of cone geometries with different RI profile fills. All the concentrators simulated in Fig. 2 have the same geometry- the input diameter is 3.5, the output diameter is 1, the height is 5, and the interior sidewalls of the cone are optically reflective. These are dimension-independent simulations in the ray domain, i.e., in the regime where the device dimensions are several times larger than the wavelength of the incident light. Details of scale invariance are presented in appendix A in the supplementary file. The angle of the incident ray array, theta, was swept from 0 to 90° in one plane as the structure has rotational symmetry. Figure 2 shows the cone geometries’ optical concentration efficiency, i.e., light transmission to the smaller output aperture versus incidence angle compared to the cosine theta theoretical maximum, i.e., projection limit when not tracking the light source. The results show that the concentrator that is air filled, homogeneously filled with RI = 3.5, or homogeneous filled with RI = 3.5 along with a lens-top reject a substantial amount of the incident light. In contrast, an AGILE with a linear gradient index from ambient to the detector material (i.e., RI from 1 to 3.5) concentrates light close to the theoretical limit. In these simulations, Fresnel reflections at the top surface are not included in most curves unless denoted in the chart legend, as an antireflection thin film can be added at the top surface. However, as seen in the curves where Fresnel reflections are included, the AGILE is unchanged, while the lens-top and high-index filled cones have reduced transmissions.
The AGILE theoretical concept
While designing optical concentrators, the constant brightness theorem18,19,20 imposes strict limits. The theorem says that the optical power-flow per unit of area and solid angle cannot be increased through a passive optical system: luminance is invariant. Stated this way, the theorem is not complete and higher luminance (formerly described as brightness) can be achieved inside a high refractive-index (RI) material, as seen in optical immersion techniques in microscopy and lithography21,22. Mathematically, due to conservation of etendue in a perfect optical system, the concentration (C) in a 3-D optical concentrator can be expressed23,24:
where ain and aout are the radii of the input and output apertures, nin and nout are the input and output refractive indices, and ∅in and ∅out are the input and output acceptance half angles. RI is denoted as n(z) in the equations. In solar concentrators, if we consider the input RI is unity and the output spread half angle as 90°, the equation reduces to \(C = \left\{ {n_{out}/sin\emptyset _{in}} \right\}^2\). Here, ∅in is close to 90°, so the concentration of the device:
equation 1 states that optical concentrators accepting all incidence angles are not in violation of the constant brightness theorem, provided that the area reduction ratio is less than or equal to the square of the ratio of RI from input to output. In this paper, we show that concentration at this limit (\(C = \left\{ {n_{out}/n_{in}} \right\}^2\)) can be achieved by gradually changing the RI from near unity in air to a high RI at the output. Extending Eq. 2, the RI continuously increases from input to output, while the area (A) of the concentrator decreases such that:
where x and y are the transversal coordinates, z is the axial coordinate, A is the cross sectional area, and n(x,y,z) is the RI. For a circularly symmetric structure of radius r(z) and a RI that is only a function of z (i.e., RI constant at each z plane), Eq. 3 can be written as
with Eq. 4 fulfilled, the number of electro-magnetic modes is constant along the height of the concentrator at each z plane; however, that condition in itself is not sufficient to ensure concentration. It is easy to find examples of structures that fulfill Eq. 4 but fail to concentrate light due to reflections from the sidewalls, e.g. jagged or discontinuous sidewalls or abrupt index variations. Therefore, the design challenge is to find concentrator shapes and corresponding index profiles that allows the electromagnetic modes of one layer to effectively couple to the next layer without unacceptable reflections.
Consider r(z) and n(z) as the sidewall and the index profiles respectively along z (height of AGILE). K is a non-zero constant and h is a dimensionless parameter that gives the height relative to the input radius, height = hK. n1 and n2 are the input and output indices, with boundary conditions: \(r\left( 0 \right) = \frac{K}{{n_1}},n\left( 0 \right) = n_1,r\left( {hK} \right) = \frac{K}{{n_2}},\&\, n\left( {hK} \right) = n_2\). By using n(z)*r(z)=K (i.e., Eq. 4) and setting the curvature, i.e., second derivatives of r(z) equal to a constant ε, give the analytical solutions. By defining the second derivative as a constant, the solutions would have parametric continuity ‘smoothness’ of the order ε2. Hence, this approach eliminates n(z) and r(z) that are unphysical and discontinuous. Different family of curves (i.e., complementary sidewall and index profiles) that create the AGILE design can be found. The analytical profiles for n(z) and r(z):
We have mainly simulated and fabricated concentrators with linear sidewalls. For ε = 0, r(z) is linear and n(z) is hyperbolic:
Height optimization
The aim of the height optimization is to design a short device to save material and weight, while maintaining efficiency. AGILE device is scalable in the ray-domain (i.e., as long as the concentrator geometry is several times larger than the wavelength of light). Details in appendix A in the supplementary file. Scalable here means the concentrating phenomena of the AGILE works in the same way even if the geometry is increased or decreased by a scale factor. In other words, if we scale the Cartesian coordinates by a common factor, the ray paths are unaffected. The consequence of scale invariance is that the characteristics and therefore the performance of a particular AGILE is purely determined by the height to input diameter ratio. In appendix A, we show that: (1) reflections in the AGILE are scale invariant and (2) the ray tracing equation in the gradient index of the AGILE is scale invariant. Therefore, the height optimization study is also scalable. Shorter AGILEs are lossy, and efficiency increases as the AGILE gets longer. One of the main ray-rejection mechanisms is from the sidewalls of the top corner area of the AGILE. As the height of concentrator gets shorter, the corner angle gets smaller. The refractive index gradient inside the AGILE in the corner area is not large enough to bend the rays before they are reflected out by the sidewall. The combined effect of the small corner angle and not enough index variation in this space is that rays escape out of a short AGILE. A tall AGILE gives a large corner angle and hence near-perfect light capture. In reality the longer the AGILE gets, the larger the material transmission losses and greater the number of reflections/bounces; hence, there is a limit to how long the AGILE should be made. Another source of loss, apart from non-ideal height of the device, could be abrupt index variations. Reference25 reports that in inhomogeneous media, even if the ∆RI (i.e., difference between largest and smallest RI) is large, as long as the RI slope is equal to ∆RI/(2λ) or smaller, the reflectivity is negligible. However, there is an abrupt limit around ∆RI/[(1/20)λ] where reflectivity increases sharply. In AGILE, the RI slope is 5 orders of magnitude lower than the abrupt limit. The index variation happens gradually over a large distance when compared to the wavelength in AGILE, so this abrupt limit, where reflections from index variations become significant, is not reached.
We use ray tracing simulations performed with the software FRED to find the optimum height as shown in Fig. 3. Both in simulations and in experiments, we focused on structures with linear sidewall geometry. Every curve in Fig. 3 is created from several simulations. Each point represents a particular AGILE device of a specific height, concentration, and index variation, and the point value gives the integration of transmission across 0° to 90° incidence angles compared to the input light, i.e., overall performance across all angles for a particular geometry. This process repeated for different heights made a curve for one concentration and index variation combination. Each curve is based on about 400 simulations. In Fig. 3, the upper bound is the maximum efficiency of 1 (all light incident on the input aperture reaching the output). The ‘height to input diameter’ ratio dictates the efficiency, as this ratio controls the sidewall angle and hence the retention of rays inside the structure. Accordingly to Eq. 3, the number of Suns concentration factor (i.e., the area reduction ratio) of 6.25, 12.25, and 20.25 are chosen to be less than, equal to, and greater than the square of index variation (3.52 and 4.52) in the simulated AGILEs, to evaluate how these curves differ from each other. For all the simulations the input diameter is the square root of the concentration and output diameter is 1. For the 6.25 Suns AGILEs the input diameter is 2.5 and output diameter is 1, for the 12.25 Suns AGILEs the input diameter is 3.5 and output diameter is 1, and for the 20.25 Suns AGILEs the input diameter is 4.5 and output diameter is 1. Height is normalized with output diameter of 1. For the various curves in Fig. 3, the efficiency almost reaches the maximum of 1 when the height of the simulated device is approximately equal to the input diameter. For example, for the curve ‘12.25 Suns, n 1 to 3.5’, a height of 3.15 with input diameter of 3.5, i.e., height : input diameter of 0.9, gives an efficiency of over 98%. A ~ 1:1 aspect ratio of height : input diameter of the AGILE structure, where the efficiency curve plateaus to almost 1, ensures a good compromise between maximizing efficiency and minimizing height.
Curves represent the concentration capacity of AGILE, i.e., efficiency, with respect to height for different geometries and refractive index ratios. A ~ 1:1 aspect ratio of height to input diameter of the AGILE structure, where the efficiency curve plateaus to almost 1, ensures a good compromise between maximizing concentration efficiency and minimizing device height. A generalized design guide is found in Eq. 8
Figure 3 curves represent the concentration capacity of AGILE with respect to height for different geometries and refractive index ratios. All the simulation data in Fig. 3 closely follow the Pareto function of the form:
with a and b as constants, H as height, and E as efficiency that approaches its maximum value Emax, which is the smaller of 1 and \({{{\mathrm{M}}}} = \frac{{n_{out}}}{{n_{in}}}/\frac{{r_{in}}}{{r_{out}}}\), as height gets large, where nin and nout are the input and output indices, and rin and rout are the input and output radii. Here height is denoted as ‘H’ and is different to the small ‘h’ parameter used before in Eq. 6. As described in Eq. 3, when the area reduction ratio, as in the concentration factor, is equal to the square of the index ratio, the AGILE is at its optimum performance. This optimum performance is shown as the ‘design guide’ fitted to the height optimization data for ‘12.25 Suns with n varying from 1 to 3.5’ and ‘20.25 Suns with n varying from 1 to 4.5’, where M = 1. The ‘12.25 Suns with n varying from 1 to 4.5’, ‘6.25 Suns with n varying from 1 to 4.5’, and ‘6.25 Suns with n varying from 1 to 3.5’ curves lie above the design-guide curve and the ‘20.25 Suns with n varying from 1 to 3.5’ curve falls below the design guide, as they respectively have more and less index gradation compared to the area reduction factor. The generalized design-guide curve is given as:
where M = \(\frac{{n_{out}}}{{n_{in}}}/\frac{{r_{in}}}{{r_{out}}}\), N = \(\frac{1}{{n_{in}}} - \frac{1}{{n_{out}}}\), and R = \(\frac{1}{{r_{out}}} - \frac{1}{{r_{in}}}\).
The above design guide characterizes how the efficiency, as in the concentrating action of the AGILE, changes with the height and can be used to create various immersion graded concentrators depending on the application requirements. The AGILE is scale invariant as described above. Therefore, the height optimization study is also scalable, and this generalized result in Eq. 8 can be applied to various geometrical concentrations and refractive index ratios, as these Pareto function curves fall above, below, or track the optimum performance.
Practical AGILE design
For photovoltaic (PV) systems where the light enters the input aperture in air (RI ≈ 1) and is absorbed in a high-index PV material (e.g. silicon with a RI ≈ 3.5), theoretical passive concentration (i.e., capturing light without tracking the movement of the source) given by Eq. 1 is (3.52/12) =12.25. Achieving this level of passive concentration requires development of materials with broadband transparency and having low to high indices creating a large range of RI spread. In this section we discuss realistic AGILE designs as compared to the theoretical simulations presented so far, i.e., available broadband transparent optical materials with a wide range of indices, the trade off between concentration and the available graded index range in the AGILE design, other practical features include tile-able/tessellated input apertures to maximize space and light capture, and an optimum height design drawing on the results of the height optimization.
Fabrication
Robust, broadband transparent, and inexpensive graded RI materials were critical to the success of the AGILE. We have designed and fabricated two variations of AGILE prototype: a pyramid of stacked glass flats, and a cluster of cones filled with polymer layers of different RI26. The fabricated pyramid with a square-cross section is a tile-able design and the rotational symmetric polymer array made by overlapping cone shapes has a tile-able/tessellated input aperture as well - going from hexagons at the input to circles at the output. Prototype designs are seen in Fig. 4a, b. After extensive material search, selection, and characterization, broadband transparent optical glasses were found to be available having index of 1.5 to 2, and broadband transparent UV curable polymers having an index of 1.46 to 1.625. Broadband transparent in this application means high optical transmission across the solar spectrum from about ~300 nm to beyond ~1200 nm. Graded index materials were fabricated as layers of different indices using the different glasses and the different polymers selected; and this was an approximation (verified via simulations) to the theoretical continuous gradient refractive index according to Eq. 3. For practicality of fabrication, we have used graded index layers. A hyperbolic refractive index profile matches the as-fabricated linear sidewalls of the devices as informed by Eq. 6. The refractive indices of different glasses and polymers in the various layers across the height of the devices fabricated are shown in Fig. 4c (glass pyramid) and Fig. 4d (polymer cluster) along with the matching theoretical continuous hyperbolic gradient index according to Eq. 6 for comparison.
AGILE structures with tile-able input surfaces: a pyramid with square cross section and b cluster of 7 overlapping cones. Height axis going from input aperture to output aperture is shown, which is true for both a and b. Refractive index gradation from low to high in the two structures along height of the device: c in the glass pyramid and d in the polymer cluster. The larger apertures at the top have a lower refractive index and the bulk material is graded to increase to a higher refractive index at the smaller apertures at the bottom. In graphs c and d, we compare the refractive indices of the different glasses and polymers used in the layers across the height of the fabricated AGILE devices (the steps) to the theoretical continuous hyperbolic index as per Eq. 6 (the dotted curves).
Materials and methods
Glass pyramid fabrication
The pyramid was made out of different optical glass flats, varying in index from 1.5 to 2 (list of glasses from Ohara Corp. in appendix B in the supplementary file). After an extensive search, these glasses were chosen from available optical-quality glasses, such that they have similar thermal expansion and glass transition temperatures, high broadband transmission in the solar spectrum, and RI evenly distributed in a wide range. To simplify fabrication, we create structures with linear sidewall geometry. The concentration efficiency difference between AGILE with the ideal hyperbolic index profile that matches a linear sidewall given in Eq. 6 and the layered index profile we fabricated is very small. In Fig. 4 c and d, we can compare how the selected material layers compare to the nominal hyperbolic index profile. The geometry of the pyramid was a square of side 14.5 mm down to a square of 8.5 mm giving a concentration of 3, along a total height of 8 mm with 8 glass layers, with each flat 1 mm thick. Glasses were cut into squares, polished on both sides, and rigorously cleaned. Bonding these different glass flats was a challenging task- melting glasses in a Kiln, silicate bonding27, diffusion bonding in a hot press28, anodic bonding29, and bonding using SoG (Spin-on-Glass)30 were attempted. We built a pressure vice for the glass flats using Teflon pins and a high-pressure mechanical vise. Direct bonding of the polished flats after plasma treatment and anodic bonding using a voltage (upto 30 kV) and heat were attempted. However, these attempts did not create the mechanically robust bonded glass stack that is necessary for machining. For the interfaces that were not anodically bonded, optical quality glue was used in between the glass flats to fill in any non-flat imperfections while being held in place under the pressure vise to remove excess glue, and this successfully created a robust graded index glass material layered from RI of 1.5 to 2. The fringe pattern before adding the glue was noted and was used to calculate the spacing between the non-ideal polished flats. There were wedges and curves seen in the fringe pattern which indicated non-uniform spacing and the maximum spacing was calculated to be 0.8 microns. The pyramid shape was micro-machined in this glass stack. To make the sidewalls reflective and not just dependent on total internal reflection, the pyramid’s sidewalls were coated with aluminium. The pyramid’s fabrication flow can be seen in Fig. 5.
Glass pyramid fabrication steps, a thin glass slabs of different refractive indices bonded together and the pyramid shape machined in the stack. Seen in the corners is the ‘checkerboard’ pattern, which is an optical illusion due to graded index layers, b aluminium deposited on the sidewalls, c pyramid in optical contact with solar cell absorbs and concentrates most of the incident light and appears dark.
Polymer cluster fabrication
For the experimental demonstration of AGILE using polymers, broadband transparent UV curable optical polymers were chosen. The single AGILE structure had the issue that in order to collect all the light at the output, it had to be directly fabricated on or optically bonded to the photodetector with an appropriate anti-reflection coating. In a back-to-back AGILE, measurements of transmission were easier because the transmitted power was back in a low-index medium, i.e., air, so a photodetector with a standard AR (Anti-Reflection) coating was sufficient. In a back-to-back AGILE, light went from a larger aperture to smaller and then back to larger, thereby proving the concentration effect. The single AGILE was the basic structure to be demonstrated, the back-to-back AGILE was made for solely testing purposes and represents the ideal AGILE concentrator fabricated directly on a detector. An array structure was made – AGILE back-to-back array of 7 overlapping cones at the input that decrease from a diameter of 7 mm to 4 mm and increase back to 7 mm over a height of 10 mm having a concentration of 3 Suns (calculation of the over-lapping input aperture area in appendix C in supplementary file). Three structures are presented in Fig. 6c: 2 Suns AGILE cone (diameter of 7 mm to diameter of 5 mm, and index variation from 1.46 to 1.56), 3 Suns (7 overlapping cones of diameter of 7 mm to diameter of 4 mm) back-to-back AGILE with 10 layers (index variation from 1.46 to 1.56), and 3 Suns back-to-back AGILE with 12 layers variation (index variation from 1.46 to 1.625). The AGILE array is an extension of demonstration of the 2 Suns AGILE to 3 Suns (diameter of 7 mm to diameter of 4 mm). UV curable polymers having different indices were cured volumetrically layer by layer in polished aluminium cone shapes to create the AGILE prototypes31. Appendix D in supplementary file gives the fabrication steps used for creating these graded index polymer stacks.
Discussion and results
Characterization and results of the glass and polymer AGILEs
In characterizing the glass pyramid performance, care was taken to establish optical contact between the pyramid and the photodetector using an index matching liquid with RI of 1.7 (Cargille Labs). This RI value is not ideal but chosen because index matching liquids with higher values are corrosive to the high-index glass of the pyramid at the output and these liquids need to be handled as hazardous materials, or the liquids have colour, i.e., not broadband transparent. The fabricated AGILEs were tested by comparing the amount of laser light reaching the photodetector via a fixed aperture area (input aperture of AGILE) with and without the AGILE to evaluate the concentrator performance. The measurement set-up is depicted in Fig. 6a, which includes a red HeNe laser, beam expander, a rotational stage, a holder for AGILE, and a photodetector. Details of the measurement set-up and the test procedure are given in appendix E in the supplementary file.
It can be seen from Fig. 6b that the two set of glass pyramid simulation results match in performance with the set of experimental results. There are, at least, two major distinct ways of measuring light concentration through a pyramid shape across different incidence angles. This is due to the fact that unlike the cone cluster the pyramid does not have rotational symmetry. The two set of results for the pyramid shape are (1) the angular measurements done with rotation along the side of square input aperture of the pyramid (annotated as ‘0° rotation’ in Fig. 6b), and (2) the rotation along the diagonal of the square input aperture of the pyramid (annotated as ‘45° rotation’ in Fig. 6b). The pyramid’s 45° rotation optical transmission results are slightly lower than the 0° rotation results. This lower transmission can be accounted for by the corner reflection action of the pyramid which may increase the number of bounces of the rays, adding losses, and which is not present when only rotating/pivoting along the sides of the pyramid. Measurements were re-done and verified using green and blue LED sources and under a solar simulator and they track the results measured using the HeNe laser; proving broadband transmission and function as a solar concentrator. Ray tracing simulations of the pyramid concentrator performance are shown in Fig. 6b, together with experimental results. The losses at each intersection/interface in the layered structure were taken into account in the simulation by including the indices and thicknesses of the glass flats and the index matching layer. Light left the pyramid from the last glass layer of RI 2 then entered the 0.2 micron index matching liquid of RI 1.7, and then the silicon material of the detector with RI of about 3.5, in that sequence. The lower transmission performance of the pyramid as compared to the simulations was due to the fact that there are thin adhesive layers in between the glasses, the material loss of the structure, and the coatings on the solar cell detector, which were not accounted for in the simulations. At normal incidence, the simulation predicts a transmission of about 0.83. In comparison, the highest transmission experimentally measured at normal incidence through the pyramid is about 0.72.
As seen in Fig. 6c, the back-to-back polymer AGILE structures gave very good performance and were able to concentrate most of the light that was incident on the 7 mm diameter circular aperture through the smaller 4 mm diameter aperture half way along the axis in each cone of the cluster. The experimental concentration efficiencies should have been similar for the single AGILE and for the glass pyramid when compared to the back-to-back results, but reflections at the AGILE-photodetector interface led to reduced transmission, as seen in Fig. 6c. This lower transmission highlights the importance of optical and mechanical bonding and immersion between the AGILE and the detector. An ideal AGILE system includes fabrication of the AGILE directly on top of a solar cell detector, for perfect light capture, propagation, and conversion. The curves in Fig. 6c show a roughly sinusoidal modulation on the transmission through the AGILE. This harmonic modulation was more pronounced with a single wavelength than with a broadband illumination, typical of interference effects. To estimate the layer thickness d in this Fabry-Perot type resonance effect, \(\normalsize \large \large \normalsize \normalsize 2\pi m = \frac{{4\pi n_fd\,{{{\mathrm{cos}}}}\theta }}{\lambda }\) with the RI of the layer, i.e., nf = 2, m = integer = 1, λ = 632.8 nm, and θ = 0°; we find d = 157 nm, which is about the approximate antireflection coating/passivation layer thickness on a standard solar cell/detector. Constructive interference at the transmission side is due to the different resonant wave-fronts that arrive in phase, enhancing the signal at specific incidence angles and opposite for destructive interference dips. This also means that the harmonic variation is not caused by the graded index layers in the back-to-back AGILE, where layers of different types of polymers over a height of 20 mm make each layer 2 mm thick in the 10 layer cluster and 1.67 mm thick in the 12 layer one. As expected, the transmission curves through all AGILE devices fall between those of the conical clusters’ 4 mm diameter (output aperture) and the 7 mm diameter (input aperture) theoretical maximum curves (red and green dotted lines). It was noteworthy that the back-to-back AGILE results (blue line with square symbols) follow the theoretical maximum cosine projection curve quite well over the full angular range (for example, at normal incidence, experimentally measured transmission through the polymer cluster is ~ 0.93, i.e., over 90% efficiency). The results demonstrate that light incident from all angles on the AGILE cluster was successfully concentrated in 3x smaller area.
Even though the inspiration for AGILE design did not come from nature, there are features of AGILE that can be found in the retina of fish (e.g. Gnathonemus) and compound eyes in insects (e.g. Lepidoptera), where a gradient index is present as anti-reflection to maximize transmission as well as to enable camouflage32,33. The human eye lens is also a layered structure of gradient RI ranging from about 1.406 to 1.38634, i.e., has (RI ratio)2 of 1.03. We have taken the gradient immersion index idea further and designed and fabricated devices with (RI ratio)2 of up to 2, pushing the limit seen in nature, the fiber optics industry, or research35,36,37.
Conclusions
Immersion-graded-index optics as an effective non-tracking optical concentrator was conceptualized, simulated, and fabricated. The design choice of 1:1 aspect ratio of height to input diameter of the AGILE structure was found to ensure a good compromise between maximizing light-capture and minimizing the device height. We present a generalized design-guide equation relating the refractive indices and the geometry, which can be used to create various immersion-graded optical concentrators.
Search for appropriate broadband transparent materials and innovation of several fabrication techniques with multiple iterations were needed to create defect free materials with a large graded RI range. Approximating the ideal gradient index with a discrete stepped index yields results that are close to the theoretical maximum. The AGILE prototypes: the glass pyramid made by stacking of various different glass flats and the polymer array of over-lapping cones made in an aluminium stencil, experimentally demonstrated a passive concentration of 3 Suns. The simple to test and verify, back-to-back AGILE array tracked the cosine theta theoretical maximum across all incidence angles. Difference between the results of single and back-to back devices brought home the importance of optical contact between the concentrator and the detector/solar cell, i.e., immersion. More sophisticated AGILE designs involve the incorporation of lens-top surface to increase light collection; sub-wavelength nano-structuring, porosity, and aerogels to create the low index side;38,39,40,41,42,43 top surface strengthening for exposure to environment;44 functionalized nano-particle filler layers45 and nano-structuring46,47 with passivation in the PV cell to create the high values of the RI, i.e., to increase the range of graded index; an optimized sidewall profile matching the index profile used according to Eq. 4; and a 3D gradient index in both axial and radial directions to decrease height of the concentrator and to eliminate the need of a reflective sidewall.
Successful optical quality fabrication and demonstration of concentrators using polymers: (1) enable lightweight-design-flexible structures and ability to fabricate directly on textured solar cells/detectors, (2) provide effective encapsulation and inexpensive panel packaging along with the PV costs offset by the optical concentration, and (3) allow possibility of large-scale manufacturing using spray coating, auto pipetting, multiscale imprint, casting, molding, and 3D printing48. Results of the functional prototypes demonstrate that immersion graded index technology can improve the way we concentrate and couple light many fold. The AGILE has the potential to greatly improve opto-electronic systems by reducing cost, increasing efficiency, providing a scalable concentration system with built-in anti-reflection and encapsulation without the need for tracking.
References
Wiesenfarth, M., Anton, I. & Bett, A. W. Challenges in the design of concentrator photovoltaic (CPV) modules to achieve highest efficiencies. Appl. Phys. Rev. 5, 041601 (2018).
O’Neill, M. et al. Recent space PV concentrator advances: more robust, lighter, and easier to track. In 2015 IEEE 42nd Photovoltaic Specialist Conference (PVSC) 1–6 (IEEE, 2015).
Madala, S. & Boehm, R. F. A review of nonimaging solar concentrators for stationary and passive tracking applications. Renew. Sustain. Energy Rev. 71, 309–322 (2017).
Leutz, R., Suzuki, A., Akisawa, A. & Kashiwagi, T. Design of a nonimaging fresnel lens for solar concentrators1. Sol. Energy 65, 379–387 (1999).
Benítez, P. et al. High performance Fresnel-based photovoltaic concentrator. Opt. Express 18, A25–A40 (2010).
Wang, G. et al. Experimental and optical performances of a solar CPV device using a linear Fresnel reflector concentrator. Renew. Energy 146, 2351–2361 (2020).
Osuna, R., Fernandez, V., Romero, M. & Marcos, M. J. PS10, a 10 MW solar tower power plant for southern Spain. Energy 2000, 386–393 (2000).
Vaidya, N. et al. Lightweight carbon fiber mirrors for solar concentrator applications. In 2017 IEEE 44th Photovoltaic Specialist Conference (PVSC) 572–577 (IEEE, 2017).
Winston, R. Dielectric compound parabolic concentrators. Appl. Opt. 15, 291–292 (1976).
McDonald, M., SolFocus Inc. Encapsulant with modified refractive index. U.S. Patent Application 12/209,675 (2010).
Karp, J. H., Tremblay, E. J. & Ford, J. E. Planar micro-optic solar concentrator. Opt. Express 18, 1122–1133 (2010).
Tremblay, E. J., Zagolla, V., Loterie, D. and Moser, C. Self-tracking planar concentrator using a solar actuated phase-change mechanism. In Physics, Simulation, and Photonic Engineering of Photovoltaic Devices II. (International Society for Optics and Photonics, 2013).
Phelan, M. et al. Outdoor performance of a tandem InGaP/Si photovoltaic luminescent solar concentrator. Sol. Energy Mater. Sol. Cells 223, 110945 (2021).
Marhic, M. E., Kotzin, M. D. & Van den Heuvel, A. P. Reflectors and immersion lenses for detectors of diffuse radiation. JOSA 72, 352–355 (1982).
Raman, A., Yu, Z. & Fan, S. Dielectric nanostructures for broadband light trapping in organic solar cells. Opt. Express 19, 19015–19026 (2011).
Solgaard, O., Dauskardt, R. & Vaidya, N. Longitudinally graded index lens. U.S. Patent 9,329,308 (2016).
Weiss, A. & Norman, J. M. Partitioning solar radiation into direct and diffuse, visible and near-infrared components. In Agricultural and Forest Meteorology 205–213 (1985).
Koshel, R. J. Illumination Engineering: Design with Nonimaging Optics. 153 (John Wiley & Sons., 2012).
Drude, P., Riborg, C. & Millikan, R. A. The Theory of Optics… Translated from the German by CR Mann and RA Millikan. (London; New York, 1902).
Smestad, G., Ries, H., Winston, R. & Yablonovitch, E. The thermodynamic limits of light concentrators. Solar Energy. Materials 21, 99–111 (1990).
Mansfield, S. M. & Kino, G. S. Solid immersion microscope. Appl. Phys. Lett. 57, 2615–2616 (1990).
Owa, S. & Nagasaka, H. Immersion lithography: its potential performance and issues. In Optical Microlithography XVI 724–733. (International Society for Optics and Photonics, 2003).
Chaves, J. Introduction to nonimaging optics. (CRC press, 2008).
Vaidya, N., Dauskardt, R. & Solgaard, O. AGILE: Axially Graded Index LEns as a non-tracking solar concentrator. In Optics for Solar Energy. (Optical Society of America, 2011).
Diamant, R. & Fernández-Guasti, M. Light propagation in 1D inhomogeneous deterministic media: the effect of discontinuities. J. Opt. A: Pure Appl. Opt. 11, 045712 (2009).
Vaidya, N. & Solgaard, O. Immersion graded index optics for passive solar concentrators. In Photovoltaic Specialist Conference (PVSC) 1–3 (IEEE, 2015).
Sinha, S., Urbanek, K. E., Krzywicki, A. & Byer, R. L. Investigation of the suitability of silicate bonding for facet termination in active fiber devices. Opt. Express 15, 13003–13022 (2007).
Gordon, L. et al. Diffusion-bonded stacked GaAs for quasiphase-matched second-harmonic generation of a carbon dioxide laser. Electron. Lett. 29, 1942–1944 (1993).
Lee, T. M., Lee, D. H., Liaw, C. Y., Lao, A. I. & Hsing, I. M. Detailed characterization of anodic bonding process between glass and thin-film coated silicon substrates. Sens. Actuators A Phys. 86, 103–107 (2000).
Lee, J. H. et al. Smart-cut layer transfer of single-crystal SiC using spin-on-glass. J. Vac. Sci. Technol. B. 30, 042001 (2012).
Vaidya, N. & Solgaard, O. 3D printed optics with nanometer scale surface roughness. Microsyst. Nanoengineering Nat. 4, 18 (2018).
Kreysing, M. et al. Photonic crystal light collectors in fish retina improve vision in turbid water. Science 336, 1700–1703 (2012).
Bernhard, C. G., Gemne, G. & Sällström, J. Comparative ultrastructure of corneal surface topography in insects with aspects on phylogenesis and function. Z. f.ür. Vgl. Physiologie 67, 1–25 (1970).
Hecht, E. Optics. In 4th International edition (Addison-Wesley, San Francisco, 2002).
Koike, Y., Ishigure, T. & Nihei, E. High-bandwidth graded-index polymer optical fiber. J. Lightwave Technol. 13, 1475–1489 (1995).
Anuszkiewicz, A. et al. Fused silica optical fibers with graded index nanostructured core. Sci. Rep. 8, 1–13 (2018).
Dylla-Spears, R. et al. 3D printed gradient index glass optics. Sci. Adv. 6, eabc7429 (2020).
Xi, J. Q. et al. Optical thin-film materials with low refractive index for broadband elimination of Fresnel reflection. Nat. Photonics 1, 176–179 (2007).
Park, K. C. et al. Nanotextured silica surfaces with robust superhydrophobicity and omnidirectional broadband supertransmissivity. ACS Nano 6, 3789–3799 (2012).
Dubois, G. et al. Superior mechanical properties of dense and porous organic/inorganic hybrid thin films. J. Sol. Gel Sci. Technol. 48, 187–193 (2008).
Ong, M. D. et al. Molecular‐controlled fracture and release of templated nanoporous organosilicate thin films. Adv. Mater. 20, 3159–3164 (2008).
Gurav, J. L., Jung, I. K., Park, H. H., Kang, E. S. & Nadargi, D. Y. Silica aerogel: synthesis and applications. J. Nanomaterials 2010, 409310 (2010).
Prakash, S. S., Brinker, C. J. & Hurd, A. J. Silica aerogel films at ambient pressure. J. Non-Crystalline Solids 190, 264–275 (1995).
Dubois, G. et al. Molecular network reinforcement of sol–gel glasses. Adv. Mater. 19, 3989–3994 (2007).
Althues, H., Henle, J. & Kaskel, S. Functional inorganic nanofillers for transparent polymers. Chem. Soc. Rev. 36, 1454–1465 (2007).
Hsu, C. M., Connor, S. T., Tang, M. X. & Cui, Y. Wafer-scale silicon nanopillars and nanocones by Langmuir–Blodgett assembly and etching. Appl. Phys. Lett. 93, 133109 (2008).
Narasimhan, V. K. & Cui, Y. Nanostructures for photon management in solar cells. Nanophotonics 2, 187–210 (2013).
Vaidya, N., Carver, T. E. & Solgaard, O. Device Fabrication Using 3D Printing. US patent 62/267,175 (2015).
Acknowledgements
Fabrication work was done in the flexible clean room in Spilker, Stanford University, and we are thankful for valuable discussions and help with custom fabrication setups from Thomas E. Carver. We are grateful to Prof. Reinhold H. Dauskardt for his advice on material science. Thanks to Michael J. Mandella for help with FRED (optical simulation software used to design AGILE). We thank Timothy R. Brand for the fabrication help in the crystal shop. Thanks to Evan Scouros for work on ray trajectory theory. We are thankful for research discussions with J Provine on fabrication, Skip Huckaby on anodic bonding, Prof. Robert S. Feigelson for advice on hot pressing of glasses, and Kiarash Zamani Aghaie for help with optical mode theory. We thank GCEP (Global Climate and Energy Project) for funding and special acknowledgement to Stanford DARE (Diversifying Academia, Recruiting Excellence) fellowship. Part of the work was performed at the Stanford Nano Shared Facilities (SNSF), supported by the National Science Foundation award ECCS-2026822.
Author information
Authors and Affiliations
Contributions
Original work of Nina Vaidya with guidance from PhD adviser Olav Solgaard.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Vaidya, N., Solgaard, O. Immersion graded index optics: theory, design, and prototypes. Microsyst Nanoeng 8, 69 (2022). https://doi.org/10.1038/s41378-022-00377-z
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41378-022-00377-z
- Springer Nature Limited