Highlights
-
Highly efficient CuEDTA removal by an electrolyzer with MoS2 nanosheet cathode.
-
Higher removal rate and Faraday efficiency compared with other widely reported electrocatalytic technologies.
-
CuEDTA/Zn primary battery is constructed for the first time to realize CuEDTA removal and synchronous power generation.
Abstract
Electrocatalytic reduction of ethylenediamine tetraacetic acid copper (CuEDTA), a typical refractory heavy metal complexation pollutant, is an environmental benign method that operates at mild condition. Unfortunately, the selective reduction of CuEDTA is still a big challenge in cathodic process. In this work, we report a MoS2 nanosheet/graphite felt (GF) cathode, which achieves an average Faraday efficiency of 29.6% and specific removal rate (SRR) of 0.042 mol/cm2/h for CuEDTA at − 0.65 V vs SCE (saturated calomel electrode), both of which are much higher than those of the commonly reported electrooxidation technology-based removal systems. Moreover, a proof-of-concept CuEDTA/Zn battery with Zn anode and MoS2/GF cathode is demonstrated, which has bifunctions of simultaneous CuEDTA removal and energy output. This is one of the pioneer studies on the electrocatalytic reduction of heavy metal complex and CuEDTA/Zn battery, which brings new insights in developing efficient electrocatalytic reduction system for pollution control and energy output.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
1 Introduction
Ethylenediamine tetraacetic acid copper (CuEDTA), one of the typical refractory and toxic heavy metal complexation pollutants, is massively discharged from industrial processes including electroplating and metallurgy [1]. The extremely stable structure and highly soluble property of CuEDTA over a wide pH range make it quite challenge to apply the traditional precipitation treatment method for this heavy metal complexation [2]. On the other hand, as a valuable metal, the recovery of Cu from CuEDTA wastewater is important for both resource utilization and pollution control [3, 4]. To realize the treatment and recovery of the complexes, a common strategy is decomplexation by oxidation coupled with the deposition of metal [2, 3, 5,6,7,8,9,10,11,12,13]. However, obstacles of high energy consumption and low removal or recovery rate/efficiency prevent the practical applications of this method. For instance, Wang et. al. reported the oxidative decomplexation of CuEDTA by HCO3−/H2O2-based advanced oxidation technique, which required ~ 2000 times of H2O2 dosage to achieve 40–92% decomplexation and 74.8% total organic carbon (TOC) removal of 0.2 mM CuEDTA in 60 min [14]. Therefore, more efficient technology for metal–organic complex removal is highly needed.
Electrochemical reduction is an electrode interface reaction process, in which the reactant gains electrons directly at the electrode, and the reaction proceeds at a certain rate when an appropriate overpotential is applied [15, 16]. Cathodic reduction has unique advantage in CuEDTA removal since Cu is directly precipitated by cathodic reduction through a two-electron process of the central Cu2+ without ligand degradation [17]. Then, the de-complexed EDTA can either be recycled or removed using less costly biological treatment techniques, which shows lower energy consumption than that of the anodic decomplexation/precipitation process [17, 18]. Direct electrochemical reduction of CuEDTA has been reported in previous studies [17,18,19,20,21]. However, these studies mainly focus on the operation parameter optimizations in the reactor including solution pH, electrolyte, current density, flow rate, etc. Although high Cu recovery efficiency can be achieved in these systems, the current efficiency is relatively low (25%) even with CuEDTA concentrations up to 10 mM [17, 21], which greatly limits the practical applications of this technology due to the unfordable energy consumption. Another important issue in electrochemical reduction of CuEDTA is that the hydrogen evolution reaction (HER) at the cathode is ignored in most cases, which is a competitive reaction for CuEDTA reduction reaction (CuRR) in cathodic reaction. To address these challenges, highly selective and efficient cathode for CuRR is needed to realize the practical applications of this technology.
2D MoS2 nanosheet (NS) has exposed edges and basal plane, which shows unique surface chemistry properties compared with its bulk form [22, 23]. MoS2 nanosheets have been reported in electrocatalytic reactions including N2 or NO reduction reaction [24,25,26], CO2 reduction reaction [27], O2 reduction reaction [28, 29], etc. In one study, Zhang et al. reported the electrochemical reduction of NO on MoS2 (1 0 1) crystalline surface. They showed that MoS2 was more conducive to NO adsorption, and the N–O bond of adsorbed NO was elongated, which benefited the subsequent electroreduction process [24]. Motivated by these studies, we speculate that MoS2 nanosheet may have promising catalytic activity in cathodic reduction of CuEDTA.
In this work, we report a MoS2 nanosheet-based electrode with abundant exposed edges for selective CuEDTA reduction. This cathode achieves high catalytic performance for CuRR, which is superior to commonly used cathodes in electrocatalytic systems including Pt/C, Cu, and carbon black [30]. Based on the density functional theory (DFT) modeling, it is shown that the activation energy of CuRR on the MoS2 surface is 0.114 eV, which is much lower than that of the graphite electrode (0.821 eV). Considering the outstanding activity of MoS2 nanosheet for CuRR, two types of electrochemical devices, i.e., electrolyzer and CuEDTA/Zn battery, are constructed and demonstrated by the MoS2/graphite felt (GF) cathode. In the electrolyzer, the MoS2/GF achieves an average Faraday efficiency (FE) of 29.6% and a high specific removal rate (SRR) of 0.042 mol cm−2 h−1 for CuEDTA at − 0.65 V versus SCE, both of which are higher than those of the (photo)electrooxidation technology-based removal systems [3, 31]. In the CuEDTA/Zn battery, a maximum power density of 1.05 mW cm−2 at 1.95 mA cm−2 can be delivered. The MoS2/GF cathode battery can achieve 75% removal of CuEDTA with a superhigh FE of 77%. To the best of our knowledge, this is the first report of CuRR coupled with battery application for the CuEDTA treatment and energy storage. The reported highly efficient and low energy consumption electrolyzer for CuEDTA removal and CuEDTA/Zn battery present new insights in the practical applications of electrochemical system for heavy metal complex treatment and energy reuse.
2 Experimental
2.1 Preparation of MoS2/GF Cathode
The MoS2/GF cathode was prepared by the hydrothermal synthesis method. In detail, 1 mmol Na2MoO4 and 5 mmol urea were dissolved in 30 mL ultrapure water. The GF (6 cm × 2 cm) was washed with dichloromethane, ethanol, and 0.1 M hydrochloric acid, successively. Then, the mixed liquor was transferred into a Teflon-lined stainless-steel autoclave. The washed GF was rolled and placed into the autoclave. After 24 h hydrothermal reaction at 200 °C, the MoS2 nanosheets were produced and deposited on the GF surface. The MoS2/GF was dried in vacuum and cut into small pieces for later use.
2.2 CuEDTA Removal by Electrolyzer
The CuEDTA electroreduction experiment was carried out in the two-compartment reaction cell separated by the ion exchange membrane. The MoS2/GF was used as the cathode (size of 3 cm2) and Pt plate was used as the anode. The CuEDTA (1 mM) and Na2SO4 (0.5 M) was used as the electrolyte for the cathode and anode compartment, respectively, and the solution volume was 30 mL for each compartment. A polymer electrolyte membrane (PEM) was used to separate the cathode and anode. During the reaction, at a predetermined sampling time, 0.25 mL reaction solution was collected and diluted with 0.25 mL H2O for real-time CuEDTA concentration determination or 0.25 mL of 1 mM CuSO4 solution for total CuEDTA concentration determination by high-performance liquid chromatography test (HPLC, Agilent 1260, USA). The real-time concentration of EDTA was obtained by subtracting the real-time CuEDTA from the total concentration. The test conditions of HPLC were as follows: the test wavelength was 225 nm, the column was C18 (4.6 × 250 mm), the volume ratio of 10 mM H3PO4 to acetonitrile water was 92:8, and the flow rate was 1 mL min−1. The standard curve of CuEDTA concentration determined by HPLC is shown Fig. S1. The electrode regeneration was achieved by soaking the Cu-deposited MoS2/GF in saturated ethylenediamine tetraacetic acid for 24 h. Tap water and surface water (filtered by 0.44 µm water phase needle filter, from Tongji University campus) were used to study the impact of coexist chemicals in real water samples on the electroreduction efficiency of CuEDTA in our system.
2.3 CuEDTA/Zn Battery Test
The CuEDTA/Zn battery was constructed in the two-compartment reaction cell separated by the bipolar ion exchange membrane (BIEM). The MoS2/GF was used as the cathode (size of 3 cm2) and Zn plate was used as the anode. The Na2SO4 (0.5 M) and KOH (1 M) was used as the electrolyte for the cathode and anode compartment, respectively, and the solution volume was 30 mL for each compartment. The output characteristics of the battery were measured by chronopotentiometry with current ramp method, and the current sweep speed was 0.1 mA s−1. The CuEDTA concentration was measured with the same method using HPLC. Chronopotentiometry was used to measure the potential change under constant current discharge condition. In both electrolyzer and battery cells, Ar was continuously pumped to prevent interference of oxygen and carbon dioxide in the air. Other experimental details of material characterizations and electrochemical tests are shown in the Supporting Information (Text S2–S3).
3 Results and Discussion
3.1 Reactor Design and Electrode Characterizations
Figure 1a shows the experimental device used in this study, which is a two-compartment reaction cell separated by an ion exchange membrane. The core reaction of the reactor is the CuRR on the cathode, which occurs in both electrolyzer and primary battery. With the MoS2/GF cathode, the CuEDTA decomplexation and reduction proceed to produce copper deposition on the cathode surface (Fig. 1b). In the electrolytic cell system, the CuEDTA is removed and Cu is recovered by the applied voltage; while the oxygen evolution occurs at the counter electrode (Fig. 1c). In the CuEDTA/Zn battery, the redox reaction between Zn and CuEDTA occurs spontaneously and generates electrical energy (Fig. 1d). In order to eliminate the interference of oxygen and other reactive gases, the devices were operated under the protection of argon.
The prepared MoS2 nanosheets with exposed edges on the GF electrode are first characterized. As shown in the scanning electron microscope (SEM) image, the GF electrode has a smooth surface (Fig. 2a). After the in-situ synthesis of MoS2 nanosheets, the GF is fully covered by a dense MoS2 layer (Fig. 2b). The nanosheet feature is evidenced by the transmission electron microscope (TEM) image shown in Fig. 2c, which indicates that the MoS2 nanosheets have a vertically-aligned structure with large number of exposed edges. The high-resolution TEM (HRTEM) image (Fig. 2d) and selected area electron diffraction (SAED) patterns (Fig. 2e) confirm the crystalline structure of MoS2. The 0.258 nm lattice fringe in the HRTEM image can be indexed to the (1 0 1) crystal plane of hexagonal MoS2 crystalline.
The X-ray diffraction (XRD) patterns in Fig. 2f show diffraction peaks at 13.9°, 33.0°, and 58.0°, which may be attributed to the diffraction peaks of polytype 2H-MoS2 or 3R-MoS2 [32, 33]. The Raman spectroscopy was further obtained to investigate the structure of the prepared MoS2 nanosheet (Fig. S2). The MoS2 nanosheet exhibits two vibration bands at 385 cm–1 (E2g) and 405 cm–1 (A1g), which demonstrates that the 2H-MoS2 phase is the major constituent [34]. The energy dispersive spectroscopy (EDS) spectrum of the prepared MoS2 nanosheet is shown in Fig. S3. In addition to Mo and S, there is also a certain amount of C, which may be attributed to the carbon in the organic thiourea from which MoS2 is synthesized. The atomic ratio of S to Mo is measured as 1.95, further confirming the successful preparation of MoS2.
The surface chemical states of MoS2 were characterized by X-ray photoelectron spectroscopy (XPS). As shown in Fig. S4, the peaks at 236.0, 232.8, and 229.3 eV can be attributed to Mo(VI) 3d3/2 of MoS2 surface plasmon, Mo(IV) 3d3/2 and Mo(IV) 3d5/2 of MoS2, respectively. The extra peak at ∼ 226.3 eV in Mo 3d XPS is referred as S 2s. The peak at 162.3 eV corresponds to Mo+ state in S 2p3/2, and the peaks at 163.3 and 169 eV are Mo2+/MoS2 surface plasmon state in S 2p1/2. The XPS results are consistent with the reported electronic structure of 2D MoS2 thin film [35].
3.2 Electrochemical Characterizations and CuRR Mechanism
Before the device demonstration of the electrochemical CuEDTA removal, electrochemical characterizations were performed to study the electrode process of CuRR on the MoS2 cathode. The catalytic activity of the prepared catalyst towards CuRR in 0.5 M Na2SO4 solution was firstly evaluated by cyclic voltammetry (CV) measurements (Fig. S5). For comparison, the voltammograms of commonly used Pt/C, Cu, carbon black (CB), and glassy carbon (GC) electrodes in electrochemical reduction territory were also tested. Compared with the CV curves recorded in the Na2EDTA solution (red curve), the redox currents were observed for MoS2 electrode, while the other electrodes showed no obvious redox currents, indicating that the MoS2 nanosheet has superior catalytic activity for CuRR.
As shown in Fig. 3a, the linear sweep voltammetry (LSV) curves further indicate that the MoS2 cathode has higher electrochemical activity for CuRR, and its reduction current exceeds those of the Pt/C, Cu, CB, and GC electrodes. Since the thermodynamic standard potential of CuEDTA reduction is lower than that of HER (Text S1), it is inevitable that the CuRR and HER will occur simultaneously. Thus, we further compared the HER and CuRR currents of the MoS2 cathode to investigate its activity and selectivity for these two competing reactions.
For the MoS2 electrode, Fig. 3b clearly shows that the reduction current of CuRR (10 mM CuEDTA) is greater than that of HER (10 mM Na2EDTA), indicating that MoS2 nanosheet cathode has a strong selectivity for CuRR over HER. In contrast, the other cathodes show different activities in CuRR and HER. As shown Fig. S6, the HER performance is excellent for Pt/C. However, the cathodic current is greatly inhibited in the presence of CuEDTA, which indicates that the Pt/C cathode has an intrinsic inferior activity of CuRR compared with HER. As for Cu cathode, the similar decrease in current density is found in the presence of CuEDTA, which may also be ascribed to the inherent lower catalytic activity for CuRR than HER. No difference is observed between the HER and CuRR currents on the CB cathode since the activity of CB cathode is low for both reactions. The above results indicate that MoS2 nanosheet has the strongest CuRR selectivity among the studied cathodes.
The limit current of CuRR on MoS2 cathode can be used to verify if the reaction is controlled by non-electron-transfer steps like mass transfer or pre-conversion steps. Hence, we carried out rotating disk electrode tests at different rotate speeds to reveal if the CuRR on MoS2 electrode was controlled by the mass transfer step. As shown in Fig. 3c, the limit current density of CuRR increases with the increased rotation speed, indicating that, in the tested potential range and rotation speed, the CuEDTA reduction reaction is controlled by the mass transfer process. Similarly, we have also carried out the rotating disk tests on the other cathodes (Fig. S6). Different from the results on MoS2 cathode, no difference was observed at various rotation speeds, indicating the non-mass-transfer controlled reaction current and their limited electrocatalytic reduction performances. The high catalytic activity and selectivity of the MoS2 cathode for CuRR can also be confirmed from the Nyquist plots (Fig. 3e), which shows smaller radius of curvature for CuRR compared with that of HER. On the other reference electrodes, there is no significant difference in the reaction resistance between HER and CuRR (Fig. S7). In addition, according to the fitting curve of the relationship between the limiting current density (jd) and the rotational angular velocity (ω1/2) in Fig. 3d, the electron transfer number is calculated to be ~ 1.9, indicating that the two-electron CuRR process is the main process in the system.
Figure 4a shows the schematic diagram of electrocatalytic reduction process of CuEDTA at the MoS2 cathode. For the electrocatalytic CuEDTA reduction, the first step is the mass transfer process of the CuEDTA to the cathode surface. Based on the above electrochemical test results, we have shown that CuRR is limited by the mass transfer on MoS2 cathode; while the CuRR on the other cathodes is limited by their inherently poor catalytic activity in the pre-conversion step under good mass transfer conditions (Text S5). In general, the vacant orbital of the central metal ion of the coordination compound is filled with lone pair electrons of the ligands; while, the existence of the vacant orbital is necessary to achieve the reduction of the central metal ion, which is the pre-conversion process. The pre-conversion process largely determines the overall efficiency of the CuRR, in which the decomplexation reaction of CuEDTA on the cathode can be expressed by the following equations:
where the numbers in parentheses represent the coordination numbers of Cu2+.
To understand how the MoS2 nanosheets catalyze the CuRR process, DFT calculation was utilized to investigate the multi-step decomplexation process in CuEDTA reduction (Text S6). The change of free energy of CuEDTA in the pre-conversion process on the MoS2 surface and graphite surface was calculated for comparison (Fig. 4c). As shown in Fig. 4b, we stipulate that the initial energy of six-coordinated Cu on the (1 0 0) crystal plane of MoS2 and the (0 0 2) crystal plane of graphite is 0 eV. Because of the Jahn–Teller effect, the energy that is needed for the CuEDTA to transform to the tetra-coordination state is decreased, which means that the transform of CuEDTA from 6 to 4 coordination is a spontaneous process. In contrast, the activation free energy of CuEDTA from four-coordinated to two-coordinated Cu is 0.821 eV for graphite and 0.114 eV for MoS2 nanosheet, respectively. This result clearly indicates that the energy required for the decomplexation of CuEDTA on the MoS2 surface is much lower than that on the graphite surface; thus, the speed of this step on the MoS2 cathode is faster than that on the carbon cathode. The DFT calculation results conform the inherent high activity of MoS2 nanosheet for the decomplexation of CuEDTA, which theoretically support that the MoS2 nanosheet cathode is suitable for electrochemical reduction removal of CuEDTA. This result also indicates that, for the electrochemical reduction removal of heavy metal complexes, the catalyst with low energy barrier for the conformation change of the complex is critical for the efficient reduction of heavy metal complexes.
3.3 CuEDTA Removal in Electrolyzer
In view of the excellent activity and selectivity of MoS2 nanosheet for CuRR, two proof-of-concept devices were constructed to investigate the practical application prospects of CuEDTA removal, which is the electrolyzer for CuEDTA removal and the CuEDTA-Zn battery (MoS2/GF, CuEDTA (SO42−)||OH−, Zn) for simultaneous Cu removal and energy output. The electroreduction removal of CuEDTA wastewater in the electrolyzer was first investigated. The CuEDTA can be directly removed by anodic oxidation at the oxygen evolution potential window according to previous report [36,37,38]. Therefore, in order to eliminate the interference of anodic electrooxidation, the two-chamber electrolyzer was used. Different cathodes including MoS2/GF, Ti, and GF were studied and compared in the electrolyzer. As shown in Fig. 5a, under good mass transfer condition by forced convection, CuEDTA can be removed fast with 84% removal rate in 10 min with the MoS2/GF cathode, which is much higher than the Ti plate (40% removal rate in 10 min) that was commonly adopted as the cathode [11, 18], and is also higher than that of the GF cathode. The high removal rate of CuEDTA by the MoS2/GF cathode further confirms that the MoS2 nanosheet has outstanding catalytic performance in CuRR.
The potentiostatic method was adopted to further study the mass-transfer controlled removal process. In the experiment, three different cathodic potentials of − 0.65, − 0.70, and − 0.75 V (vs. SCE) were applied. At these potentials, the removal rates of CuEDTA are almost the same as shown in Fig. 5b. The results match well with the electrochemical characterization results, which indicate that the mass transfer rate determines the CuRR process in the applied potential range. The current density of the cathode at three different cathodic potentials were also recorded (Fig. S8). The HER current density reaches the stable status rapidly after the transient unstable electrode process (capacitor charging current and Faraday reaction current); while the CuRR current density gradually decreases. The reason for the CuRR current drop can be understood by the following dynamic equation of mass transfer-controlled electrode process:
where C is the reactant concentration in solution, Cs is reactant concentration at electrode surface, n is the electron transfer number, F is the Faraday constant, D is the diffusion coefficient of CuEDTA, l is the thickness of the diffusion layer. As the reactant concentration, i.e., the CuEDTA concentration, decreases, the current density decreases. When the current density of CuRR becomes zero, the remaining cathode current is attributed to the HER current. It is found that the current densities are close under the applied cathodic potentials, which matches with the CuEDTA removal rates under different cathodic potentials (Fig. 5b).
The electroreduction of CuEDTA is an unstable or unsustainable process due to the coverage of the MoS2/GF cathode by Cu deposition. To evaluate the durability of the cathode, the recycling test was carried out. As shown in Fig. 5c, after 3 cycles, a degradation of the cathode performance is noticed. The SEM images of the cathode surface after the reaction confirm the deposition and coverage of Cu on the cathode (Fig. S9). The Cu-deposited electrode can be refreshed in saturated ethylene diamine tetraacetic acid, and its catalytic activity for CuEDTA removal can be fully recovered as shown in the 4th cycle. The above results show that the reported MoS2/GF cathode has good practical application potential for CuEDTA wastewater treatment.
Furtherly, we investigated the impact of coexist chemicals in real environment water on the CuEDTA removal efficiency of our system. As shown in Fig. S10, it is found that the removal efficiencies of CuEDTA in tap water and pure water are almost the same; while the removal efficiency in surface water (100% CuEDTA removal in 10 min) is even higher. The results show that the coexist chemicals in tap water and surface water have no inhibiting effect on CuEDTA removal, demonstrating the potential of the system for practical environmental application. In addition to CuEDTA, we also measured the EDTA concentration during the electrochemical reduction process (Fig. S11). The results show that the ligand EDTA in CuEDTA remains unchanged during the electrode reaction process. The ligands alone are not toxic and can be further processed through inexpensive biological processes or recycled as industrial products. These results further demonstrate the potential of the system for practical environmental applications.
By integrating the chronoamperometric curve, the FE of CuEDTA removal at different potentials was obtained (Text S4). The specific removal rate (SRR) and FE of the MoS2/GF cathode at the applied potentials are close, mainly due to the mass transfer limitation and the high selectivity for CuRR of MoS2 nanosheet (Fig. 5d). The FE of the MoS2/GF cathode in CuEDTA removal reaches 29.6% at the cathodic potential of − 0.65 V, while the highest SRR is obtained at 0.042 mol cm−2 h−1. In order to demonstrate the superiority of the MoS2/GF-based electrochemical deposition (E.D.) system, the FE and SRR values of this system were compared with other electrooxidation-based coupling systems (Fig. 5e) [3, 9, 31, 39, 40]. The electrochemical reduction system based on MoS2/GF cathode is superior to the reported coupling systems based on electrooxidation, electrodeposition, photo-electrooxidation, electrocoagulation, and Fenton combined electrodeposition. Specially, the removal efficiency of the MoS2/GF-based electrochemical deposition system is one to three orders of magnitude higher than those of the reported systems (see details in Table S1).
3.4 CuEDTA Removal in Zn-CuEDTA Battery
In another demonstrated system, we constructed a CuEDTA-Zn battery with MoS2/GF as the cathode and Zn as the anode. The galvanic cell device not only can remove the CuEDTA, but also realizes the output of electric energy. The electrode reactions involving the Zn-CuEDTA battery are shown as follows:
As shown in Fig. 6a, the as-built Zn-CuEDTA battery delivers a maximum power density (10 mM CuEDTA) of 1.05 mW cm−2 at 1.95 mA cm−2 by the MoS2/GF electrode. In contrast, only 0.50 mW cm−2 of maximum power density is achieved at 1.35 mA cm−2 by the GF electrode. The output current density of the MoS2/GF electrode with even 1 mM CuEDTA is also larger than that without CuEDTA (Fig. S12), confirming that the battery performance depends on the CuEDTA reduction reaction. The output performance of our Zn-CuEDTA battery can reach the level of Zn-NO batteries, exceeding the level of some reported Zn-CO2 and Zn-N2 batteries (Table S2).
The simultaneous CuEDTA removal and output performance of MoS2/GF and GF electrodes at 0.5 mA cm−2 current density are shown in Figs. 6b and S13, respectively. The output voltage of the battery decreases gradually for both MoS2/GF and GF electrodes along the discharge process. This decrease can be attributed to two reasons. Firstly, the concentration polarization gradually increases due to the decrease of CuEDTA concentration (removal of CuEDTA) in the battery discharge process. Secondly, the deposition of Cu on the electrode surface leads to the electrode deactivation. By integrating the voltage-charge curve, we calculated the cumulative electrical output of the Zn-CuEDTA battery. In 1 h of discharge, the battery with the MoS2/GF electrode outputs 1.9 J; while the battery with the GF electrode outputs 0.6 J only.
For the battery’s cycling test, in the first three cycles, the FE and removal efficiency of the battery with MoS2/GF electrode gradually decrease. However, by using the same regeneration method, the FE and removal efficiency of the battery can be well recovered, as show in Fig. 6c. It is noticed that the battery with MoS2/GF electrode has an outstanding FE of 77%, which is several times higher than the other reported systems in CuEDTA removal (Fig. 5e). The above results indicate that the MoS2/GF electrode has high electrical output performance in CuEDTA-Zn battery, which is attributed to the excellent catalytic performance of MoS2 nanosheet in CuRR.
To demonstrate the power output characteristic of the CuEDTA-Zn battery, a 20 mW LED light was powered by the Zn-CuEDTA battery. It is found that the bulb does not emit light when the battery is constructed with 1 mM CuEDTA electrolyte (Fig. 6d). However, by increasing the concentration of CuEDTA to 10 mM, the LED light can be lit (Fig. 6e). Through putting batteries in series, the LED light emits much stronger light (Fig. 6f). The LED light experiment further confirms the power output characteristic of the Zn-CuEDTA battery and demonstrates that the higher electrical power output can be obtained by higher CuEDTA concentration in actual CuEDTA wastewater treatment. The above results show that the prepared MoS2/GF electrode has a practical application potential in CuEDTA-Zn battery for efficient pollutant removal and simultaneous power output.
4 Conclusion
In this study, MoS2 nanosheet-based electrode was demonstrated in both electrolyzer and CuEDTA-Zn battery for highly efficient CuEDTA removal. The electrolyzer with MoS2/GF cathode has a specific removal rate up to 0.042 mol cm−2 h−1 and Faraday efficiency of 29.6%. On the other hand, the CuEDTA-Zn battery based on MoS2/GF electrode can simultaneously remove CuEDTA and deliver electric power output with a 1.05 mW cm−2 maximum energy density in 10 mM CuEDTA solution at 1.95 mA cm−2 current density. The battery with MoS2/GF cathode has a superhigh Faraday efficiency of 77% at 0.5 mA cm−2 discharge current density. Both systems achieve superior performances in terms of the Faraday efficiency and specific removal rate than those of the other reported electrooxidation-based systems. The density functional theory modeling confirms that the activation energy of CuRR on the MoS2 nanosheet surface is much lower than that of the other electrode, which explains the high activity and selectivity of MoS2 in CuRR. This study not only reports an efficient electrochemical reduction system for metal complex pollutant removal but also a potential electrocatalytic system for simultaneous metal complex pollutant removal and energy output.
References
W. Guan, B. Zhang, S. Tian, X. Zhao, The synergism between electro-Fenton and electrocoagulation process to remove Cu-EDTA. Appl. Catal. B-Environ. 227, 252–257 (2018). https://doi.org/10.1016/j.apcatb.2017.12.036
M. Pan, C. Zhang, J. Wang, J.W. Chew, G. Gao et al., Multifunctional piezoelectric heterostructure of BaTiO3@graphene: decomplexation of Cu-EDTA and recovery of Cu. Environ. Sci. Technol. 53(14), 8342–8351 (2019). https://doi.org/10.1021/acs.est.9b02355
X. Zhao, L. Guo, J. Qu, Photoelectrocatalytic oxidation of Cu-EDTA complex and electrodeposition recovery of Cu in a continuous tubular photoelectrochemical reactor. Chem. Eng. J. 239, 53–59 (2014). https://doi.org/10.1016/j.cej.2013.10.088
Y. Zhu, W. Fan, T. Zhou, X. Li, Removal of chelated heavy metals from aqueous solution: a review of current methods and mechanisms. Sci. Total Environ. 678, 253–266 (2019). https://doi.org/10.1016/j.scitotenv.2019.04.416
H. Zeng, S. Tian, H. Liu, B. Chai, X. Zhao, Photo-assisted electrolytic decomplexation of Cu-EDTA and Cu recovery enhanced by H2O2 and electro-generated active chlorine. Chem. Eng. J. 301, 371–379 (2016). https://doi.org/10.1016/j.cej.2016.04.006
T. Wang, Y. Cao, G. Qu, Q. Sun, T. Xia et al., Novel Cu(II)-EDTA decomplexation by discharge plasma oxidation and coupled Cu removal by alkaline precipitation: underneath mechanisms. Environ. Sci. Technol. 52(14), 7884–7891 (2018). https://doi.org/10.1021/acs.est.8b02039
T. Wang, Q. Wang, H. Soklun, G. Qu, T. Xia et al., A green strategy for simultaneous Cu(II)-EDTA decomplexation and Cu precipitation from water by bicarbonate-activated hydrogen peroxide/chemical precipitation. Chem. Eng. J. 370, 1298–1309 (2019). https://doi.org/10.1016/j.cej.2019.04.005
S.S. Lee, H. Bai, Z. Liu, D.D. Sun, Green approach for photocatalytic Cu(II)-EDTA degradation over TiO2: toward environmental sustainability. Environ. Sci. Technol. 49(4), 2541–2548 (2015). https://doi.org/10.1021/es504711e
H. Zeng, S. Liu, B. Chai, D. Cao, Y. Wang et al., Enhanced photoelectrocatalytic decomplexation of Cu-EDTA and Cu recovery by persulfate activated by UV and cathodic reduction. Environ. Sci. Technol. 50(12), 6459–6466 (2016). https://doi.org/10.1021/acs.est.6b00632
Y. Cao, X. Qian, Y. Zhang, G. Qu, T. Xia et al., Decomplexation of EDTA-chelated copper and removal of copper ions by non-thermal plasma oxidation/alkaline precipitation. Chem. Eng. J. 362, 487–496 (2019). https://doi.org/10.1016/j.cej.2019.01.061
X. Huang, Y. Xu, C. Shan, X. Li, W. Zhang et al., Coupled Cu(II)-EDTA degradation and Cu(II) removal from acidic wastewater by ozonation: performance, products and pathways. Chem. Eng. J. 299, 23–29 (2016). https://doi.org/10.1016/j.cej.2016.04.044
H. Rong, C. Zhang, Y. Sun, L. Wu, B. Lian et al., Electrochemical degradation of Ni-EDTA complexes in electroless plating wastewater using PbO2–Bi electrodes. Chem. Eng. J. 431, 133230 (2022). https://doi.org/10.1016/j.cej.2021.133230
Y. Sun, C. Zhang, H. Rong, L. Wu, B. Lian et al., Electrochemical Ni-EDTA degradation and Ni removal from electroless plating wastewaters using an innovative Ni-doped PbO2 anode: optimization and mechanism. J. Hazard. Mater. 424, 127655 (2022). https://doi.org/10.1016/j.jhazmat.2021.127655
Z. Xu, C. Shan, B. Xie, Y. Liu, B. Pan, Decomplexation of Cu(II)-EDTA by UV/persulfate and UV/H2O2: efficiency and mechanism. Appl. Catal. B-Environ. 200, 439–447 (2017). https://doi.org/10.1016/j.apcatb.2016.07.023
H. Qin, Z. Ye, X. Wei, X. Liu, X. Liu et al., Bifunctional electrolyzation for simultaneous organic pollutant degradation and hydrogen generation. ACS ES&T Eng. 1(9), 1360–1368 (2021). https://doi.org/10.1021/acsestengg.1c00173
H. Qin, X. Wei, Z. Ye, X. Liu, S. Mao, Promotion of phenol electro-oxidation by oxygen evolution reaction on an active electrode for efficient pollution control and hydrogen evolution. Environ. Sci. Technol. 56(9), 5753–5762 (2022). https://doi.org/10.1021/acs.est.1c08338
A. Eivazihollagh, J. Bäckström, M. Norgren, H. Edlund, Influences of the operational variables on electrochemical treatment of chelated Cu(II) in alkaline solutions using a membrane cell. J. Chem. Technol. Biotechnol. 92(6), 1436–1445 (2017). https://doi.org/10.1002/jctb.5141
A. Eivazihollagh, J. Backstrom, M. Norgren, H. Edlund, Electrochemical recovery of copper complexed by DTPA and C12-DTPA from aqueous solution using a membrane cell. J. Chem. Technol. Biotechnol. 93(5), 1421–1431 (2018). https://doi.org/10.1002/jctb.5510
R.S. Juang, L.C. Lin, Efficiencies of electrolytic treatment of complexed metal solutions in a stirred cell having a membrane separator. J. Membr. Sci. 171(1), 19–29 (2000). https://doi.org/10.1016/s0376-7388(99)00377-4
R.S. Juang, L.C. Lin, Electrochemical treatment of copper from aqueous citrate solutions using a cation-selective membrane. Sep. Purif. Technol. 22–3(1–3), 627–635 (2001). https://doi.org/10.1016/s1383-5866(00)00168-4
R.S. Juang, L.C. Lin, Treatment of complexed copper(II) solutions with electrochemical membrane processes. Water Res. 34(1), 43–50 (2000). https://doi.org/10.1016/s0043-1354(99)00112-8
M. Chhowalla, H.S. Shin, G. Eda, L.-J. Li, K.P. Loh et al., The chemistry of two-dimensional layered transition metal dichalcogenide nanosheets. Nat. Chem. 5(4), 263–275 (2013). https://doi.org/10.1038/nchem.1589
Q.H. Wang, K. Kalantar-Zadeh, A. Kis, J.N. Coleman, M.S. Strano, Electronics and optoelectronics of two-dimensional transition metal dichalcogenides. Nat. Nanotechnol. 7(11), 699–712 (2012). https://doi.org/10.1038/nnano.2012.193
M. Tursun, C. Wu, Vacancy-triggered and dopant-assisted NO electrocatalytic reduction over MoS2. Phys. Chem. Chem. Phys. 23(35), 19872–19883 (2021). https://doi.org/10.1039/d1cp02764f
L. Zhang, J. Liang, Y. Wang, T. Mou, Y. Lin et al., High-performance electrochemical NO reduction into NH3 by MoS2 nanosheet. Angew. Chem. Int. Edit. 60(48), 25263–25268 (2021). https://doi.org/10.1002/anie.202110879
X. Li, T. Li, Y. Ma, Q. Wei, W. Qiu et al., Boosted electrocatalytic N2 reduction to NH3 by defect-Rich MoS2 nanoflower. Adv. Energy Mater. 8(30), 1801357 (2018). https://doi.org/10.1002/aenm.201801357
R. Li, J. Liang, T. Li, L. Yue, Q. Liu et al., Recent advances in MoS2-based materials for electrocatalysis. Chem. Commun. 58(14), 2259–2278 (2022). https://doi.org/10.1039/d1cc04004a
T. Wang, D. Gao, J. Zhuo, Z. Zhu, P. Papakonstantinou et al., Size-dependent enhancement of electrocatalytic oxygen-reduction and hydrogen-evolution performance of MoS2 particles. Chem. Eur. J. 19(36), 11939–11948 (2013). https://doi.org/10.1002/chem.201301406
I.S. Amiinu, Z. Pu, X. Liu, K.A. Owusu, H.G.R. Monestel et al., Multifunctional Mo-N/C@MoS2 electrocatalysts for HER, OER, ORR, and Zn-Air batteries. Adv. Funct. Mater. 27(44), 1702300 (2017). https://doi.org/10.1002/adfm.201702300
J. Lee, J. Lim, C.-W. Roh, H.S. Whang, H. Lee, Electrochemical CO2 reduction using alkaline membrane electrode assembly on various metal electrodes. J. CO2 Util. 31, 244–250 (2019). https://doi.org/10.1016/j.jcou.2019.03.022
P. Song, C. Sun, J. Wang, S. Ai, S. Dong et al., Efficient removal of Cu-EDTA complexes from wastewater by combined electrooxidation and electrocoagulation process: Performance and mechanism study. Chemosphere (2022). https://doi.org/10.1016/j.chemosphere.2021.131971
Q. Xiang, J. Yu, M. Jaroniec, Synergetic effect of MoS2 and graphene as cocatalysts for enhanced photocatalytic H2 production activity of TiO2 nanoparticles. J. Am. Chem. Soc. 134(15), 6575–6578 (2012). https://doi.org/10.1021/ja302846n
L. Zhang, J. Liang, Y. Wang, T. Mou, Y. Lin et al., High-performance electrochemical NO reduction into NH3 by MoS2 nanosheet. Angew. Chem. Int. Edit. 60(48), 2110879 (2021). https://doi.org/10.1002/anie.202110879
B. Zong, Q. Li, X. Chen, C. Liu, L. Li et al., Highly enhanced gas sensing performance using a 1T/2H heterophase MoS2 field-effect transistor at room temperature. ACS Appl. Mater. Interfaces 12(45), 50610–50618 (2020). https://doi.org/10.1021/acsami.0c15162
S. Sarma, S.C. Ray, Magnetic behaviors of single crystal-MoS2 (MoS2-SC) and nanoparticle-MoS2 (MoS2-NP) and bi-layer-MoS2 thin film. J. Magn. Magn. Mater. 546, 168863 (2022). https://doi.org/10.1016/j.jmmm.2021.168863
P. Song, C. Sun, J. Wang, S. Ai, S. Dong et al., Efficient removal of Cu-EDTA complexes from wastewater by combined electrooxidation and electrocoagulation process: performance and mechanism study. Chemosphere 287, 131–971 (2022). https://doi.org/10.1016/j.chemosphere.2021.131971
J. Xie, J. Ma, S. Zhao, T.D. Waite, Flow anodic oxidation: towards high-efficiency removal of aqueous contaminants by adsorbed hydroxyl radicals at 1.5 V vs SHE. Water Res. 200(2021). https://doi.org/10.1016/j.watres.2021.117259
J. Xie, C. Zhang, T.D. Waite, Hydroxyl radicals in anodic oxidation systems: generation, identification and quantification. Water Res. 217, 118425 (2022). https://doi.org/10.1016/j.watres.2022.118425
X. Zhao, L. Guo, B. Zhang, H. Liu, J. Qu, Photoelectrocatalytic oxidation of Cu-II-EDTA at the TiO2 electrode and simultaneous recovery of Cu-II by electrodeposition. Environ. Sci. Technol. 47(9), 4480–4488 (2013). https://doi.org/10.1021/es3046982
X. Zhao, J. Zhang, J. Qu, Photoelectrocatalytic oxidation of Cu-cyanides and Cu-EDTA at TiO2 nanotube electrode. Electrochim. Acta 180, 129–137 (2015). https://doi.org/10.1016/j.electacta.2015.08.103
Acknowledgements
This work was supported by the National Key R&D Program of China (2019YFC1905400) and the Fundamental Research Funds for the Central Universities (2022-4-ZD-08).
Funding
Open access funding provided by Shanghai Jiao Tong University.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no interest conflict. They have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Qin, H., Liu, X., Liu, X. et al. Highly Selective Electrocatalytic CuEDTA Reduction by MoS2 Nanosheets for Efficient Pollutant Removal and Simultaneous Electric Power Output. Nano-Micro Lett. 15, 193 (2023). https://doi.org/10.1007/s40820-023-01166-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40820-023-01166-7