Abstract
The purpose of this work is to study the effect of anisotropic plasticity on the micro-deep drawing of the 304 stainless steel foils through a combination of experimental testing and numerical modeling. A phenomenological anisotropic model, with the Yld2004-18p yield function, is used to model the anisotropic plasticity deformation of the material. Based on the miniature tensile experimental data and Voce's hardening law, the coefficients in the Yld2004-18p function were calibrated. The FE modelling was implemented using ABAQUS to simulate the micro-deep drawing experiments. The wall thickness and height of the cylindrical cup obtained by the simulation have shown to be reasonably close to the experimental values, and the distribution of ears is the same as the experimental results. It has shown that the Yld2004-18p anisotropic yield function can accurately describe the anisotropic behavior of 304 stainless steel foils during the micro-deep drawing process.
Similar content being viewed by others
References
Persano A, Quaranta F, Taurino A, Siciliano PA, Iannacci J (2020) Thin film encapsulation for RF MEMS in 5G and modern telecommunication systems. Sensors 20(7):2133. https://doi.org/10.3390/s20072133
Tao K, Tang L, Wu J, Lye SW, Chang H, Miao J (2018) Investigation of multimodal electret-based MEMS energy harvester with impact-induced nonlinearity. J Microelectromech Syst 27:276–88. https://doi.org/10.1109/JMEMS.2018.2792686
Arbabi E, Arbabi A, Kamali SM, Horie Y, Faraji-Dana MS, Faraon A (2018) MEMS-tunable dielectric metasurface lens. Nat Commun 9(1):812. https://doi.org/10.1038/s41467-018-03155-6
Mallik S, Chowdhury D, Chttopadhyay M (2019) Development and performance analysis of a low-cost MEMS microphone-based hearing aid with three different audio amplifiers. Innov Syst Softw Eng 15:17–25. https://doi.org/10.1007/s11334-019-00325-7
Xu Q, Li X, Chan CY (2018) Enhancing localization accuracy of MEMS-INS/GPS/in-vehicle sensors integration during GPS outages. Ieee T Instrum Meas 67(8):1966–1978. https://doi.org/10.1109/TIM.2018.2805231
Shimizu T, Ogawa M, Yang M, Manabe K (2014) Plastic anisotropy of ultra-thin rolled phosphor bronze foils and its thickness strain evolution in micro-deep drawing. Mater Des 56:604–612. https://doi.org/10.1016/j.matdes.2013.11.048
Tang W, Huang S, Li D, Peng Y (2015) Mechanical anisotropy and deep drawing behaviours of AZ31 magnesium alloy sheets produced by unidirectional and cross rolling. J Mater Process Technol 215:320–326. https://doi.org/10.1016/j.jmatprotec.2014.08.020
Demin VA, Larin SN, Riskin RV, Rizkova AA (2018) Study the influence of anisotropy on the drawing cylindrical part. CIS Iron Steel Rev 16:25-28. https://doi.org/10.17580/cisisr.2018.02.05
Yoon JH, Cazacu O, Yoon JW, Dick RE (2010) Earing predictions for strongly textured aluminum sheets. Int J Mech Sci 52(12):1563–1578. https://doi.org/10.1016/j.ijmecsci.2010.07.005
Plunkett B, Cazacu O, Barlat F (2008) Orthotropic yield criteria for description of the anisotropy in tension and compression of sheet metals. Int J Plasticity 24(5):847–866. https://doi.org/10.1016/j.ijplas.2007.07.013
Banabic D, Barlat F, Cazacu O, Kuwabara T (2020) Advances in anisotropy of plastic behaviour and formability of sheet metals. Int. J. Mater 13:749–787. https://doi.org/10.1007/s12289-020-01580-x
Habraken AM, Aksen TA, Alves JL (2022) Analysis of ESAFORM 2021 cup drawing benchmark of an Al alloy, critical factors for accuracy and efficiency of FE simulations. Int. J. Mater 15(5):61. https://doi.org/10.1007/s12289-022-01672-w
Lou Y, Zhang S, Yoon JW (2019) A reduced Yld 2004 function for modeling of anisotropic plastic deformation of metals under triaxial loading. Int J Mech Sci 161:105027. https://doi.org/10.1016/j.ijmecsci.2019.105027
Rong H, Ying L, Hu P, Hou W (2021) Characterization on the thermal anisotropic behaviors of high strength AA7075 alloy with the Yld 2004–18p yield function. J Alloy Compd 877:159955. https://doi.org/10.1016/j.jallcom.2021.159955
Neto DM, Oliveira MC, Alves JL, Menezes LF (2014) Influence of the plastic anisotropy modelling in the reverse deep drawing process simulation. Mater Des 60:368–379. https://doi.org/10.1016/j.matdes.2014.04.008
Chai L, Luan B, Xiao D, Zhang M, Murty KL, Liu Q (2015) Microstructural and textural evolution of commercially pure Zr sheet rolled at room and liquid nitrogen temperatures. Mater Des 85:296–308. https://doi.org/10.1016/j.matdes.2015.06.088
He W, Li F, Zhang H, Chen H, Guo H (2019) The influence of cold rolling deformation on tensile properties and microstructures of Mn18Cr18 N austenitic stainless steel. Mat Sci Eng 764:138245. https://doi.org/10.1016/j.msea.2019.138245
Liu H, Wang Y, Li B, Ma X, Wu R, Hou L, Zhang J, Zhang M (2019) Effect of cryogenic rolling process on microstructure and mechanical properties of Mg-14Li-1Al alloy. Mater Charact 157:109903. https://doi.org/10.1016/j.matchar.2019.109903
Basak S, Panda SK, Lee MG (2020) Formability and fracture in deep drawing sheet metals: Extended studies for pre-strained anisotropic thin sheets. Int J Mech Sci 170:105346. https://doi.org/10.1016/j.ijmecsci.2019.105346
Hu P, Liu YQ, Wang JC (2001) Numerical study of the flange earring of deep-drawing sheets with stronger anisotropy. Int J Mech Sci 43(1):279–296. https://doi.org/10.1016/S0020-7403(99)00119-8
Othmen KB, Sai K, Manach PY, Elleuch K (2019) Reverse deep drawing process: material anisotropy and work-hardening effects. P I Mech Eng L-J Mat 233(4):699–713. https://doi.org/10.1177/146442071770195
Tiwari P R, Rathore A, Bodkhe M G(2022) Factors affecting the deep drawing process–A review. Mater Today: Proc 56:2902-2908. https://doi.org/10.1016/j.matpr.2021.10.189
Bruschi S, Altan T, Banabic D, Bariani PF, Brosius A, Cao J, Ghiotti A, Khraisheh M, Merklein M, Tekkaya AE (2014) Testing and modelling of material behaviour and formability in sheet metal forming. Cirp Ann-Manuf Techn 63(2):727–749. https://doi.org/10.1016/j.cirp.2014.05.005
Nachbagauer K (2014) State of the art of ANCF elements regarding geometric description, interpolation strategies, definition of elastic forces, validation and the locking phenomenon in comparison with proposed beam finite elements. Arch Comput Method Eng 21(3):293–319. https://doi.org/10.1007/s11831-014-9117-9
Yadav A D (2008) Process analysis and design in stamping and sheet hydroforming. PhD dissertation The Ohio State University:175
Tuninetti V, Oñate A, Valenzuela M (2023) Characterization approaches affect asymmetric load predictions of hexagonal close-packed alloy. J. Mater. Res. Technol. 26:5028–5036. https://doi.org/10.1016/j.jmrt.2023.08.255
Sun W, Yue Z, Wen Z, Li M (2023) An overview on material parameter inverse and its application to miniaturized testing at elevated temperature. J. Mater. Res. Technol. 22:3132–3145. https://doi.org/10.1016/j.jmrt.2022.12.159
Bouchaâla K, Ghanameh MF, Faqir M, Mada M, Essadiqi E (2021) Numerical investigation of the effect of punch corner radius and die shoulder radius on the flange earrings for AA1050 and AA1100 aluminum alloys in cylindrical deep drawing process. Heliyon 7(4). https://doi.org/10.1016/j.heliyon.2021.e06662
Cai G, Yang J, Yuan Y, Yang X, Lang L, Alexandrov S (2020) Mechanics analysis of aluminum alloy cylindrical cup during warm sheet hydromechanical deep drawing. Int. J. Mech. Sci 174:105556. https://doi.org/10.1016/j.ijmecsci.2020.105556
Zheng G, Li X, Chang Y, Wang C, Dong H (2018) A comparative study on formability of the third-generation automotive medium-Mn steel and 22MnB5 steel. J Mater Eng Perform 27:530–540. https://doi.org/10.1007/s11665-018-3183-3
Narayanasamy R, Narayanan CS (2008) Forming, fracture and wrinkling limit diagram for if steel sheets of different thickness. Mater Des 29(7):1467–1475. https://doi.org/10.1016/j.matdes.2006.09.017
Acknowledgements
The authors are grateful to the Ministry of Science and Technology of the P.R. China (G2021003007L). This work is also supported by the Modern Equipment Manufacturing Collaborative Innovation Center of Southern Hebei New District.
Author information
Authors and Affiliations
Corresponding authors
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Shang, L., Huang, S., Hu, J. et al. Anisotropic plasticity deformation during micro-deep drawing of 304 foils: An experimental and numerical investigation. Int J Mater Form 17, 21 (2024). https://doi.org/10.1007/s12289-024-01822-2
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12289-024-01822-2